Public Health Engineering Department Tender

100 mm Cast Iron Wafer type butterfly valve as per BS-5155, having body of cast iron as per IS 210 gr FG-260 disc of SS Gr CF-8, Shaft of Stainless Steel AISI-410, "O" ring for shaft seal of Nitrile rubber,valves are suitable for PN 1.0 Rating Valves are operated by suitable rotork range (three phase 415 V) multi turn electrical actuator without starter.

200 mm Cast iron doubled flanged non rising spindle sluice valve conforming to IS 14846 having body door/dome/bonnet and cover of cast iron Gr FG 260, outside screen rising Spindle of IS 6603 Gr-12 cr-13 , spindle nut and seat rings are Gunmetal as per IS:318 LTB 2. Flanges flat faced and drilled to IS:1538 Part IV and VI , Valves are suitable for maximum working pressure of 16 Kg/sqcm (seat test) and body tested to 15/24 Kg/cmsq .

Supply, delivery & fabrication at site of MS Pipe with delivery pipe of 100 mm (DN 100 medium class thickness 4.50 mm and length 15 mtr) & common header of 200 mm (DN 200 medium class thickness 4.775 mm and length 15 mtr) by providing all required materials to complete the pipe line as per NIT Specification.

Supply Delivery and strorage at site bourdon type syphone arrangement Compound gauges 150 mm dia cast Aluminium Dial with, SS internal, DN 15 GI impulse line with three way cock as per NIT Compound gauges for pump suction line for clear water Pumps. (1) Range +1 to -1 KSCG.

Painting of the installation by two coats of enamel paints (colour to be decided by purchaser) over a coat of primer as per NIT specification & direction of EIC.

Installation of all items including erection materials, MS fabricated pipe supports, valve supports etc. as required for installation of Pumping Machinery up to the entire satisfaction of EIC in compliance with NIT specification. (Cost includes hire charges of generator, welding set, fuels, lubricants etc. for completion of work)

Supplying and fixing 415V,160A TPN SFU with sheet steel enclosure on /angle iron frame on wall with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating.

Supply, Delivery and Installation of 2 mm. thick CRCA Sheet Steel Enclosed Cubical type Indoor Floor Mounted 415 Volt PDB Panel having Required No. of Feeders Supply of necessary items(For Intake Point)

Supply, Delivery and Installation, Testing & Commissioning of Outdoor type LT LPBS for motor on off .

Supply, Delivery and storage at site 70 sqmm. 3½ Core1.1 KV Grade XLPE insulated Al. Armoured Power Cable .(From Main Switch to L.T Panel via voltage stabillizer for Intake site)

Supply, Delivery and storage at site 25 sqmm. 3 Core1.1 KV Grade XLPE insulated Al. Armoured Power Cable.(From L.T Panel to Intake Pump Motor)

Supply, Delivery and storage at site 6 sqmm. 2 Core1.1 KV Grade XLPE insulated Al. Armoured Power Cable..(From L.T Panel to intake light)

Supply, Delivery and storage at site 2.5 sqmm. 8 Core1.1 KV Grade XLPE insulated Cu Armoured Control Cable.(From L.T Panel to LPBS )

Supply, Delivery and storage at site 3 core flat submersible cable 10 sq mm ,1.1 KV grade ,copper conductor

Laying of two cables upto 35 sqmm in an underground trench in single tier formation (horizontal), the trench size : 680 mm x 760 mm average depth, with brick protection on the top of each cable 8 (eight) Nos. bricks per Mtr. and 4 (four) Nos. bricks per Mtr. as separator between the bricks and cables and also trench to be filled up with shifted soil, levelling up and restoring surface duly rammed

Laying of one No. cable upto 35 sqmm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed

Laying of cable upto 3/4 core 25 sqmm on wall/surface including S & F MS clams with earthing attachment in 2 x 10 SWG GI (Hot Dip) Wire, making hole etc. as necy., mending good damages and painting

Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables as below :

3.5 core 70 sqmm cable

3core 25 sqmm cable

2core 6sqmm cable

Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials :

3.5 core 70 sqmm cable

3core 25 sqmm cable

2core 6sqmm cable

Making Earthing Arrangement

Earthing with 80 mm dia GI pipe (TATA-Medium)x 3.0 Mts long and 1 x 19/8 stranded GI (Hot Dip) wire (4 Mts. long), 25mm dia x 150 mm long galvanized bolt, double nuts, double washers including socketing at both ends of stranded GI (Hot Dip) wire by crimping sockets/ thimbles and S & F 40 mm dia GI pipe (ISI-Medium) protection (3 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level to an average depth of 3.65 Mts

Extra for providing masonery enclosure on the top of the earthelectrode of overall size 86.36 cm x 86.36 cm x 46 cm deep(below Ground level) complete with cemented brick work(1:6)of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm withlocking arrangement, GI reducer including drilling of 46 nos.12 mm dia holes on the GI pipe

Extra for treatment of soil by using salt & charcoal or coke for plate electrode.

Connecting the equipments body to earth busbar including S&F 25 mm x 6 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl.drilling holes, with bolts, nuts, washers etc.

Supplying and fitting-fixing of earth busbar of galvanized (Hot dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolt,nuts,washers,spacing isolator set etc.as required Length of busbar

Supply & delivery of moulded Chair as per directon of EIC.

Supply & delivery of moulded Table as per directon of EIC.

Making internal wiring/electrification of the Meter house by (2x 22/0.3 (1.5 sqmm) + 1x 22/0.3 (1.5 sqmm) single core PVC insulated multistrand FRLSH Grade flexible copper wire through 20 mm PVC conduit pipe/casing by supplying required module PVC Board & piano key type switch. (ave. run 6 mtr). i) LED Tube set point-2 nos., Lamp light point- 2 no., 5 pin 6 Amps. Plug point- 2 no., with necy. earthing arrangement & one fan point (Total point 5 nos. points) including drawing power by suitable gauge (2.5 mm² of copper wire from Mcc panel to DB and for 3nos external lighting arrangement through 20 mm PVC casing capping (precision make) as per direction of EIC wiring should be with continuous earthing arrangement and 20W Two nos. 4 ft long LED tube light sets,9W 2nos. LED lamp , one no. 0-4 step fan with regulator (Humfree) etc to be supplied by agency and 1no 74watt LED fixture with arm bracket at outside.

Supply delivery at site and storage of safety equipment like Fire Extinguisher, shock treatment chart and first aid box,11000 volt danger board complete

Supply and delivery at site of 75KVA, 3 phase oil cooled type Servo Motor operated copper wound line voltage corrector conforming to IS-9815 (Pt.-1)-1994 suitable for un-balanced input voltage with following specification including first filling oil as per IS-335 where applicable.(Make: Approve make of P.H.E. Dte.) a) Input Voltage:- 3 phase, Main supply may or may not be balanced with respect to Phase to Phase 250V.-500V.Phase to Neutral-145V.-290V. b) Out put voltage:- 3 phase balanced out put voltage. Phase to Phase 400V.or 415V.± 1% ,Phase to Neutral- 230V.-240V.±1% ( Provision should be made to adjust the Variation of out put voltage per phase by a variable pot oil within ± 5% of out put). c) Line regulation:- Out put voltage should remain well with ±1% of set voltage ( From Minimum to Maximum i.e. either 400V. or 415V. supply variation). d) Load regulation : Out put voltage should remain neutral well within ±1% of set voltage be (From no load to full load ) i.e. either 400V. or 415V. e) Correction speed:- Better than 35 Volt / Second. f) Efficiency:- Better than 95% on full load. g) Cut off limit for ( minimum & maximum ) by limit switch with Audio & Visual. h) Metering Indication:- By Selector switch provision should be made available to measure input mains supply and out put voltage other stabilizer for load current measurement an Ammeter with selector switch should be available. i) Lamp Indication :- For Input & Output should be provided. ( 3 lamps per side ). j) MCB Protection: For Input side. k) Load protection : HRC Fuse on each out put phase should be available. l) Output over shoot:- Beyond 210V to . 255V /phase in case of “ MANUAL MODE” & voltage protection :AUTO MODE” operation.(Manufacturing test certificate should be provided at the time of delivery) m) VISUAL Indication for under voltage & over voltage of output. n) Manual Mode:- Up & Down correction with O / P voltage over shoot protection. Beyond 210 V-255 V. per phase. o) Nature of cooling:- Oil/ air cooled system . p) Electric current over load protection . q) Circuit for delay out put . r) Input high voltage cut - off above 500 V. s) Mode of Operation:- AUTO/MANUAL with a provision to restore the normal working of the unit “STANDBY OPERATION” should be available increase of any Electronic failure in auto mode. t) Auto Mode:- Normal * Standby.( Manufacturing test certificate should be Provided at the time of delivery)

Supply and delivery of following materials

i) Supplying and fixing 125A,415V,FP on load front Changeover switch with Sheet Steel enclosure on flat iron frame on wall with nuts bolts etc

ii) Supplying and fixing 415V, 125A TPN SFU with sheet steel enclosure on /angle iron frame on wall with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating.

iii) Supplying & fixing 125A,415V,4 Barsheet metal (16 SWG) Iron Clad Busbar chambers on angle iron frame on wall, incl. earthing attachment and painting as required – ( As per Drawing no. 470 of PWD Specification Book – May 1991)(4 X 15 X 3 mm, Box - 500mm X 150 mm) per direction of the EIC.

Making brick built foundation with supplying of all required materials suitable for the above Voltage stabilizer by (4:1) cement mortar including holding down foundation bolts(If required) and plaster with neat cement finish as per direction of E.I.C.

Installation of the above voltage stabilizer of item on the foundation including all connection complete as per direction of E.I.C.

Making Earthing Arrangement-

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts.long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above groundlevel driven to an average depth of 3.65 Mts. below the ground level as below: By ISI-Medium GI pipe .

Extra for providing masonery enclosure on the top of the earthelectrode of overall size 86.36 cm x 86.36 cm x 46 cm deep(below Ground level) complete with cemented brick work(1:6)of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm withlocking arrangement, GI reducer including drilling of 46 nos.12 mm dia holes on the GI pipe

Extra for treatment of soil by using salt & charcoal or coke forplate electrode.

Connecting the equipments body to earth busbar including S&F 20 mm x 3 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipments incl.drilling holes, with bolts, nuts, washers etc.

Supplying and fitting-fixing of earth busbar of galvanized (Hot dip) MSflat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolt,nuts,washers,spacing isolator set etc.as required Length of busbar is 0.5mtr.

Compound Light

Supply & delivery at site of 9mtrs long steel tubular pole(410 SP-26)( Bottom- 114.3 X 4.5)(Middle- 88.9 x4.05)(Top - 76.1 x 3.25)(Asper PWD Schedule) including supply & fixing of single arm header of 40 mm dia and 1.5 m long .CI base plate , CI cap etc.

Erection of 9Mtr Single Steel tubular pole of length as given below with sole plate & Cap etc. in CC foundation (Proportion and dimension indicated below), having 600x600x750 mm thick CC (4:2:1) base block below sole plate/pole with hard jhama metal including CC (6:3:1) muffing 0.30 mts. dia and 0.30 mts. above ground level including 3 mm thick neat cemented finish and GI earth bolt and earthing arrangement by 8SWG GI Wire,after making drilled holes etc. on pole including filling up the excavated earth pit with shifted soil and ramming properly.

Extra on items 2 above, for providing CC (6:3:1) base block (around the pole) dimension 0.45x0.45x0.60 mt. above ground level, neatly cemented finish (3 mm thick), at the base pole (in lieu of CC muffing) suitable for alkathene/ polythene pipe entry as directed for street light wiring, incl. S & F 20cmx15cmx10cm GI Loop box, 16SWG & incl. drilled hole in pole

Supply and fitting-fixing of 150 watt LED fixtures (Model- BRP360 LED 213 CW HO SLC S1 PSU GR of Philips / similar spec of other approved make ) on the top of the pole.It includes the cost of hiring of ladder and making necessary interconnection complete by supplying of suitable gauge Cu wire as per direction of EIC

Earthing with 1 no. of G.I. earth spike ( 20 mm dia X 1.5 mtre. Long ) driven into the ground upto 2 mtr. Drawing earth lone with separate 6 SWG . G.I. Wires providiing 15 mm dia G.I. pipe protection from earth spike feeder bos / junction box / poles andfixing to the same by suitable nuts & bolts all comete as per direction of EIC.

Painting of Steel Tubular Pole of lengths and no. of coats of paint, as given below with ready mixed paint/primer of approved make, and brand incl. preparation of surface by sand paper/emery paper, cleaning etc. for receiving fresh coat of paint

A) 1st coat of aluminium paint over RO priming

B) 2nd coat of aluminium paint over 1st coat

Testing & Commissioning the Voltage Stabilizer along with other electrical equipment’s to ensure performance of the newly procured / installed equipment’s in running satisfactorily as per direction of E.I.C.

Trial operation & maintenance of the above installation on 24 hours basis including guarding after commissioning.

Supply, delivery and storage at site of wall mounted vacuum operated gaseous chlorinator, capacity 0 - 1 kg/hr with all equipment, instrument and accssories including 4 (Four) nos. 100 Kg cylinders (2W+2S) and Neutralisation Pit arrangement as per NIeT specification Make : Wallace & Tiernan (Evoqua) / Capital Control / CAPCO TC & GC to be submitted during delivery of materials. [Make and drawing to be approved from E.I.C before placement of order ]

Installation the components as described in sl. No. 1.00 as per technical specification including supply of all erection materials, providing dosing point on the rising main by making required size of hole, clamping the dosing unit including drawing power line to booster pumps and leak detector with necessary earthing as per I.E. rules upto the satisfaction of E.I.C.

Construction of neutralization pit having size (2mtrX1.5mtr.X1.5mtr)

Supply, delivery and storage at site of Caustic Soda Flakes as per IS-252-2013 (@300 kg/site)

Supply, delivery at site of 1 no 100 Amp. T.P.N. Main switch with re-wireable Fuse system with iron frame and fixing the same on wall by supplying necessary fixing materials for receiving 3 phase power connection from Pump house along with supplying and drawing of 4 core, 25 sq mm Al. Armoured cable from 100 amp Main Switch to control panel (approx 15 mtr.) as required.

Making internal wiring/electrification of the chlorine room by ( 1.5sqmm X 2 + 1.5mm. X 1 ECC) single core PVC insulated multistrand FR Grade flexible cu. wire through 20 mm dia rigid PVC conduit pipe by supplying one 240/415 V, 16 Amp DP MCB of Breaking capacity 10kA & C characteristics with MCB SS enclosure with IP-20/30 protection, PVC Board & piano key type switch. (avg. run 5 mtr)- 18watt wall mounted LED Batten- 3 nos, 9W LED lamp-2 nos, 36 W LED luminarie (BRP 046) OR equivalent and same techinal specification, 5pin 5Amp Plug point, 240V 48"(1200mm) sweep BEE 3 star rating(minimum) AC ceiling fan with electronic step regulator-1 no., Two no Exhaust fan point (Total point 7nos. with one plug point) including drawing power by suitable gauge Cu.wire from panel board to DP MCB as per direction of EIC (fittings should be of Philips make & rising should be with continuous earthing arrangement)

Excavation of soil for installation of Earth Electrode and filling & ramming for soft soil

Earthing with 50 mm dia GI pipe (TATA-Medium)x 3.0 Mts. long and 1 x 19/8 stranded GI (Hot Dip) wire (4 Mts. long), 25 mm dia x 150 mm long galvanized bolt, double nuts, double washers including socketing at both ends of stranded GI (Hot Dip) wire by crimping sockets/ thimbles and S & F 40 mm dia GI pipe (ISI-Medium) protection (3 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level to an average depth of 3.65 Mts.

Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work(1:6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm with locking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe

Extra for treatment of soil by using salt & charcoal or coke for pipe electrode

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 50 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required.

Connecting the equipments to earth busbar including S & F GI (Hot Dip) wire of Solid GI wire (8 SWG) on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages.

Supply and Delivery at site Moulded Table. Make : Supreme ( Model- Arjun)/Nilkamal ( Model – Marvel)/Any other make approved by EIC

Supply and Delivery at site Moulded Chair. Make : Supreme ( Model- Dream)/Make : Nilkamal (Model – HR-4002)/Any other make approved by EIC.

Trial operation, maintanance of the entire system by engaging 2 nos. operating personnel for 3(three) months. (Wages to be given to the operator on prevealing rate i.e. (Rs. 404/- + 8.33% bonus)/day as on the day of operation icluding bonus.)

[Make: As per departmental approved vendor list]

Add GST @18%

Add Labour Welfare Cess @ 1%