Police Department Tender

(I) Cement concrete with graded stone ballast (40 mm size excluding shuttering) In ground floor (A) [Pakur Variety] (a) 1:3:6 proportion For foundation

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (i) Pakur Variety For Tie Beam

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge. For PCC For Steps For Tie Beam

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction (a) For works in foundation and upto roof of ground floor/upto 4 m II. Other than SAIL/ TATA/RINL

Brick work with 1st class bricks in cement mortar (1:6) (a) In foundation and plinth

Brick work with 1st class bricks in cement mortar (1:6) (b) In superstructure, ground floor For GL to Floor level Above floor level For piller For Steps

125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor.

A) Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (payment to be made on measurement of finished quantity)

Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes. For Steps For Floor

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] i) With 1:6 cement mortar (b) 20 mm thick plaster (inside plaster)

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] i) With 1:6 cement mortar (b) 20 mm thick plaster (inside plaster) (c) 15 mm thick plaster (out side plaster) For steps(side) For steps(Top)

Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m Outside of the wall For steps(side) For steps(Top) For Wall For Piller

Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4)withstonechips, laid inpanelsasdirected with topping made with ordinary or white cement (as necessary) andmarble dust in proportion (1:2) including smooth finishingand roundingoff corners including raking out jointsorrougheningofconcretesurfaceand application of cement slurrybefore flooringworksusingcement@1.75 kg/sq.m all complete including all materials and labour. In ground floor. 3mm. thick topping(Highpolishinggrindingonthis itemis not permitted with ordinary cement). Using grey cement (ii) 25 mm. Thick For Floor

(a) M.S.or W.I. Ornamental grill of approved design joints continuouslyweldedwithM.S, W.I. Flats and bars of windows, railingetc. fittedandfixedwithnecessaryscrewsandlugsinground floor. (i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr.

M.S. structural works with hollow sections (square or rectangular shape) conforming to IS: 806-1968 & IS:1161-1998) connected to one another with bracket, gusset, cleat as per design, drawing & direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. Payment to be made on the basis of calculated weight of structural memebrs of MS Holow Section as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made by adding the actual weight of such items with weight of finished structural members. The rates are considered for a hight of erection 8 m. / 2nd floor level from the ground. Add 1.5 % extra over the rate for each additional floor or 4m. beyond the initial 8 m. or part thereof. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete. i) For roof truss works a) Span up to 12 Mtr

Supplying, fitting&fixingZn-Alalloy(55%Al&45%Zn) coating of 150 grams per sq. metre (followed by colour coatedonbothside) steel sheet work havin gminimum yield strengthof550Mpaof trapizoidal profile of approved make (excluding the supporting framework) fitted and fixed with 55mm & 25mmself tapping screw, EPDM Washer16mm dia&3mmth.washeretc. complete with 150mm end lap and one corrugation minimum side lap.(Payment tobemade on area of finished work). (i) In Roof:- a) With 0.5 mm thick sheet

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC In Ground Floor: (a) One Coat

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground floor (Two Coat) a) Normal Acrylic Emulsion

Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface.Two Coats

a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc

b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (a) On timber or plastered surface : With other than hi-gloss of approved quality (iii) One coat (with any shade except white)

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface : (iv) Two coats (with any shade except white)

Sub Total

GST 18%

LWC 1%