Northeast Frontier Railway Tender

Supply, installation, testing & commissioning of indoor/outdoor panel (Suitable as per site) floor/ wall mounted cubicle type (Suitable as per site condition) main power panel suitable for 415v.50Hz AC supply made out of 14 SWG CRCA sheet .The panel shall be CPRI approved totally enclosed, dust & vermin proof, neoprene gasket of thickness not less than 2mm shall be used between all adjacent units & beneath all covers so that the joints are effectively dust vermin proof. The panel shall have uniform height & depth and plugged with insulated &spring loaded thumb screws. The bus bar chamber shall have three phase & neutral copper busbar of ratings not less than 500Amp. The panel shall be completely factory wired with insulated FRLSH copper wire & shall be 21 ready for connection to be equipments. The panel shall be painted with two coats of synthetic enameled grey paint over a coat of red oxide primer. Cable connection to be done by lug /socket of proper size and cable gland to be provided with proper insulation at every cable entrance and exit of panel. Necessary spreader link is to be fixed in proper location as per direction of Railway Engineer. Adequate size of rubber grommet is to be provided for incoming & outgoing of cables. The earthing system is to be done as per drawing no. PCEE/ELG/DRG/2024/1,dt. 30.09.2024 attached at annexure- D. Pre-inspection of materials by Railway Engineer should be imparted.. The panel shall consists of the followings : a) MCCB 100 A , 4P,18kA = 1 no b)MCCB 80A, 4P ,18kA = 4nos, c)MCCB 63A ,4P, 18kA = 2 no d)Digital ammeter, voltmeter with selector switch = 1 set e) Indicator lamp with toggle switch =1 set (RYB) Make : Legrand, LK, ABB, Schneider

Supply , testing, installation & commissioning of 10 HP 3 phase , (Star delta) water 44 cooled submersible pump motor set head range : 64 mtr to 29 mtr , Discharge range 20m3/hr to 50 m3/hr , internal Outlet size - 75/3 inch , External Outlet size 100/4 inch is to be fixed in proper location as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make- KSB, Crompton, Havells

Supply and erection of fencing uprights is to be done as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted.

Supply & erection of GI swaged steel tubular pole 7.5mtr , 410 SP-4 height with single header arm bracket 42.4x3.2mm thk x 0.5mtr long , with 250x250x12mm base plate is to be fixed in 14 proper location as per direction of Railway Engineer. Necessary foundation bolts is to be supplied by the firm as per site consition. Specification of the pole is given below : Bottom : 114.3 x3.65 mm thickness x4.5 Mtr Long Middle : 88.9x3.25mm thickness x1.5 Mtr long TOP : 76.1x3.25mm thickness x1.5 Mtr long Pre- inspection of materials by RITES should be imparted. Make- Utkarsh , Crompton, Bajaj

Supply & fixing of modular plug point 16A, 6 pin is same as item no.26, except the line 30 shall be drawn by single core stranded FRLSH insulated 2.5sqmm, 1100 volt grade copper cable. 16A, 6 pin socket and 16A separate flush type modular switch to be fixed with platinum white plate on MS board as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make- P-Socket/ Modular Switch- Legrand, Crabtree, LK, Anchor

Supply & fixing 120W LED flood light luminaries with secondary optics made with 19 pressure die- cast housing and heat sink in alluminium extrusion with IP: 66 is to be fixed in proper location as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make : Philips, Bajaj, Crompton, Havells

Gravel spreading is to be done as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted.

Supply & fixing 30W LED street light with pressure die- cast housing along with 15 prismatic polycarbonate diffuser and LEDs with secondary optics and IP 65 protection is to be fixed in proper location as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make : Philips, Bajaj, Crompton, Havells

Supply , testing, installation & commissioning of 5 HP 3 phase , DOL water cooled 45 submersible pump motor set head range : 70 mtr to 23 mtr , Discharge range 9m3/hr to 24 m3/hr , Outlet size - 65mm is to be fixed in proper location as per direction of Railway Engineer. Pre- inspection of materials by Railway Engineer should be imparted. Make- KSB, Crompton, Havells

Supply & fixing 200W LED flood light luminaries with secondary optics made with pressure die- cast housing and heat sink in alluminium extrusion with IP: 66 is to be fixed in proper location as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make : Philips, Bajaj, Crompton, Havells

Supply & erection of CI pipe 80 mm dia LA type complete with boring below the track by 90 mm dia hole at a depth of 1.5 m below GL by turning pointed instrument as per direction of 51 Railway engineer. The CI pipe below the track is required for laying of cable. The cabling work is to be done as per drawing no. PCEE/ELG/DRG/2024/2, dt. 04.10.2024 attached at annexure-C. Pre- inspection of materials by Railway Engineer should be imparted. Make - ELECTRO STEEL CASTING LTD, KESHORAM SPUN.

Supply & erection of HDPE pipe 50mm dia of pressure rating 6.0 kgf/ cm2 (PN -6.0) 7 are to be laid along the pole/ beam/brackets by 25x5 mm MS clamp with required nut, bolt/ washer and under the ground by digging trench of depth 1mtr if necessary. Necessary compression socket and short radius compression bend has to be provided as per direction of Railway Engineer. Pre- inspection of materials by Railway Engineer should be imparted. Make- AJAPLAS, SWASTIK, Prime

Supply, installation, testing & commissioning of distribution board 8way is to be commissioned as per direction of Railway Engineer. The switch is to be provided on suitable place being observing IE rules & other safety measures. Cable connection to be done by lug /socket of proper size and cable gland to be provided with proper insulation at every cable entrance and exit of distribution board where necessary. Pre-inspection of materials by Railway Engineer should be imparted. The board comprising with C series MCCB/MCB's with the following items: a)DP MCB 32A = 1no, b)SP MCB 20A = 2no c)SP MCB 10A = 4 no Make : Legrand, LK, ABB, Schneider

Earthing complete with 50mm dia, 3.6mm thickness , B class GI pipe of 3000 mm length to be erected inside an earth pit is to be filled by alternate layers of salt (2) & charcoal (3) of width 50 cm each from the bottom and the rest by earth. The GI strip should be welded with the earth pipe. The pipe is provided with a tapered casing at the lower end in order to facilitate the driving. A 49 funnel with perforated plate to be provided at the top of the pipe for pouring water during dry season to have an effective earth value. The earth fill shall be of homogeneous layer of common earth soil. Where soil resistivity is high, earth resistivity enhancing materials may be used , Bentonite or similar earth enhancing materials may be used in rocky soil. Earth box to be pre casted RCC. The entire earthing system is to be done as per drawing no. PCEE/ELG/DRG/2024/1, dt. 30.09.2024 attached at annexure-D. The distance of earth electrode form building/other earthing system to be maintained by observing IE rules. Earth electrode to be procured from RDSO/Core approved source.

Installation, testing & commissioning of Water cooler with all necessary associated items for successful commissioning of water coolers is to be fixed in proper location as per direction of Railway Engineer. (water cooler will be procured through Store).

Installation, testing & commissioning of 100 KVA transformer with all necessary associated items for successful commissioning of transformer is to be fixed in proper location as per direction of Railway Engineer. (100 KVA Transformer will be procured through store)

Supply, erection, testing & commissioning of signages of size 625 sqinch photo frame type, rectangular/square shape, linear LED module mounted on PCB with fully integrated heat sink 38 mechanism as per Railway commercial code with both side visibilities to be provided including power connection. Proper mounting / hanging arrangement should be provided by the contractor for proper commissioning of the signages. All the petty items for commissioning also to be provided by the contractor. Pre-inspection of materials by Railway Engineer should be imparted. (Sample approval from Divisional in-charge is to be taken prior execution)

RCC foundation as per M25 grade with minimum cement concrete of 330kg/cum, providing & laying in position ready mixed or site batched design mixed cement concrete or reinforce cement concrete work, using coarse aggregate and fine aggregate derived from natural sources, 24 Portland pozzolana /ordinary /Portland /Portland slag cement , admixtures in recommended proportions as per IS: 9103 to accelerate/retard setting of concrete , to improve durability and workability without impairing strength; including pumping of concrete to site of lying, curing, carriage for all leads; shuttering work is also involve. The work is to be done as per direction of Railway engineer.

Supply & fixing of changeover switch 100A, 4P with enclosure is to be fixed in proper location as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make : Legrand, LK, ABB, Schneider

Installation, testing & commissioning of RAC with all necessary associated items like cu pipe for successful commissioning of RAC is to be fixed in proper location as per direction of Railway Engineer. (RAC will be procured through store).

Supply, installation, testing & commissioning of High Mast Tower 16mtr long including 120 watt LED luminaries , carriage , panel complete with erection with all accessories being fulfilling 1 the necessary criteria- dynamic loading , proper foundation, lantern carriage, head frame, winch power tool , earthing cables including luminaries as per specification of Annexure-A. Pre-inspection of materials by RITES should be imparted. Make - High Mast Tower - Utkarsh , Bajaj, Crompton, Valmont Luminaries - Bajaj , Philips, Crompton, Havells

Supply & laying of 16sqmm 4core alluminium armoured LT XLPE cable is to be laid 5 through HDPE pipe as per direction of Railway Engineer. Marking (without embossing) on saddle/ clamp/Cable/ HDPE pipe to be done mentioning the name of feed. Pre-inspection of materials by Railway Engineer should be imparted. Cable laying should be done as per drawing no. PCEE/ELG/DRG/2024/2, dt.04.10.2024 enclosed at Annexure-C. (Necessary lug and other petty items should be supplied by contractor for successful commissioning). Make- Finolex, Havells , Polycab, KEI

Supply & fixing 150W LED flood light luminaries with secondary optics made with 18 pressure die- cast housing and heat sink in alluminium extrusion with IP: 66 is to be fixed in proper location as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make : Philips, Bajaj, Crompton, Havells

Supply & laying of FRLSH PVC insulated 4sqmm single core multi-stranded copper 32 cable IS:694 to be laid concealed through suitable size alkathene pipe including 1sqmm single core FRLSH IS:694 multi stranded copper wire is to be used as per direction of Railway Engineer where necessary. Pre-inspection of materials by Railway Engineer should be imparted. Make - Finolex, Havells, KEI, Polycab

Supply & fixing of wall bracket fan point (Concealed modular) is same as item no. 26. Pre-inspection of materials by Railway Engineer should be imparted.

Supply & fixing of indoor LED fitting including T8 LED tube of 18-20watt is to be provided as per direction of Railway Engineer. Connection of fitting is to be done by 1.5sq.mm FRLHS 31 s/core copper cable. Pre-inspection of materials by Railway Engineer should be imparted. (Test certificate, guarantee/warranty certificate from manufacturer for 3 years from the date of commissioning & purchase documents from the manufacturer is to be produced by the contractor at the time of supply of materials) Make- Philips, Crompton, Bajaj, Havells

Supply & fixing of cable PVC loop box of 4way terminal (IP: 66) for suitable entry of 11 cable is to be fixed as per direction of Railway Engineer. (Necessary petty items required for successful commissioning of loop box is to be supplied by contractor). Pre-inspection of materials by Railway Engineer should be imparted. Make- Hensel, Rittel, OBO, Schneider

Supply , testing, installation & commissioning of 5 HP 3 phase , DOL water cooled 46 submersible pump motor set head range : 70 mtr to 23 mtr , Discharge range 9m3/hr to 24 m3/hr , Outlet size - 65mm is to be fixed in proper location as per direction of Railway Engineer. Pre- inspection of materials by Railway Engineer should be imparted. Make- KSB, Crompton, Havells

Supply & laying of 50sqmm 4core alluminium armoured LT XLPE cable is to be laid through HDPE pipe as per direction of Railway Engineer. Marking (without embossing) on saddle/ 3 clamp/Cable/ HDPE pipe to be done mentioning the name of feed. Pre-inspection of materials by Railway Engineer should be imparted. Cable laying should be done as per drawing no. PCEE/ELG/DRG/2024/2, dt.04.10.2024 enclosed at Annexure-C. (Necessary lug and other petty items should be supplied by contractor for successful commissioning). Make- Finolex, Havells , Polycab, KEI

Supply of steel reinforcement for RCC work is to be done as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted.

Supply & fixing of BLDC exhaust fan 250 mm sweep, including louver shutter input 35 voltage 220-240, RPM 1300 is to be fixed in proper location as per direction of Railway Engineer. Pre- inspection of materials by Railway Engineer should be imparted. Make - Philips, Crompton, Bajaj, Havells

Supply and erection of anticlimbing device for Switching stations is to be done as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted.

Supply & fixing of GI Pipe 80mm dia medium class as per IS : 1239 part-1 dated, 3rd April'2025 is to be fixed in proper location as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make- TATA, BANSAL, JINDAL

Supply & fixing of industrial socket with plug 63A outdoor type with MCB DP 63A with PVC enclosure is to be fixed in proper location as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make : Legrand, LK, ABB, Schneider

Supply & fixing of ceiling fan point (concealed modular) is same as item no.26, 28 including supply & fixing of modular type step electronic fan regulator 100W as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make - Regulator - Crabtree, LK, Legrand, Anchor

Muffing of existing Rail pole with cement concrete mixture in a ratio of 1:2:4 by cement, sand and 19 mm down stone chips from bottom of the rail to 30 cm above the ground level & as per direction of Railway Engineer.

Supply & fixing of 100A, 18kA 4P MCCB with suitable enclosure is to be fixed in proper location as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make : Legrand, LK, ABB, Schneider

Supply & fixing of pole to pole GI 8 SWG earth continuity wire covered with PVC alkathene pipe is to be fixed in proper location as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted.

Supply , testing, installation & commissioning of 12.5 HP 3 phase , (Star delta) water 43 cooled submersible pump motor set head range : 74 mtr to 34 mtr , Discharge range 20m3/hr to 50 m3/hr , internal Outlet size - 75/3 inch , External Outlet size 100/4 inch is to be fixed in proper location as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make- KSB, Crompton, Havells

Reinforced concrete for foundation and plinth in other than hard soil & rock (Grade M- 20) is to be done as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted.

Supply & laying of 70sqmm 4core alluminium armoured LT XLPE cable is to be laid through HDPE pipe as per direction of Railway Engineer. Marking (without embossing) on saddle/ 2 clamp/Cable/ HDPE pipe to be done mentioning the name of feed. Pre-inspection of materials by RITES should be imparted. Cable laying should be done as per drawing no. PCEE/ELG/DRG/2024/2, dt. 04.10.2024 enclosed at Annexure-C. (Necessary lug and other petty items should be supplied by contractor for successful commissioning). Make- Finolex, Havells , Polycab, KEI

Supply & fixing of 6A, 5 pin modular plug point is same as item no-26. The modular 29 plug socket to be fixed with platinum white plate on MS board as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make- P-Socket/ Modular Switch- Legrand, Crabtree, LK, Anchor

Supply and erection of fencing panels at switching stations is to be done as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted.

Supply & fixing of direct online starter of 5HP, 3.7kW, over load relay range 6A-9A, 48 conforms to IS/IEC 60947-4-4, provided with protection degree IP :54 is to be fixed in proper location as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make- LK , Havells, Crompton, Schneider

Machine boaring is to be done where necessary through HDPE pipe 150mm dia (PN-8) with horizontal boaring of hole across Rly embankment at a depth of 2 mtr below GL by HDD 50 machine. The entire work is to be executed as per direction of Railway Engineer. (The detailed sketch plan consisting location, depth of boaring and route layout diagram of machine boaring is need to be submitted and it should be approve by the competent authority before execution of the work. The cabling work is to be done as per drawing no. PCEE/ELG/DRG/2024/2, dt. 04.10.2024 attached at annexure-A. HDPE pipe Make- AJAPLAS, FINOLEX, SWASTIK

Supply, installation, testing and commissioning of outdoor feeder pillar box double door including Cu busbar (IP-66) is to be fixed on 48inchx36inchx48inch foundation. The CC foundation is to be done M-15 grade pain cement concrete (Cement content considered @ 240kg/cum). The design and drawing of the foundation should be approved by the competent 23 authority before the execution of the work. The feeder pillar shall be painted with two coats of synthetic enameled grey paint over a coat of red oxide primer. Suitable spreader link should be provided with the protection switches of the feeder pillar. Adequate size of rubber grommet is to be provided for incoming & outgoing of cables. Pre-inspection of materials by Railway Engineer should be imparted. The feeder pillar shall consists of the followings: a)MCB 4P 32A-01no, B) MCCB 4P 63A- 01 C) Cu busbar = set Make : Legrand, LK, ABB, Schneider

Supply, installation, testing & commissioning of 25A AC starter is to be fixed in proper location as per direction of Railway Engineer. Connection is to be drawn by single core stranded FRLSH insulate 4sqmm, 1100 volt grade copper cable confirming to IS-694 through alkathene pipe of 40 suitable size to be fixed inside wall by having final plastering with necessary coupler /elbow /Tee / 4way etc. The point to be terminated by modular type 25A AC starter on suitable size modular G.I.box& platinum white plate at one end and by 25A DP MCB on MCB Distribution Boards with 1sqmm single core IS : 694 multi stranded FRLSH copper wire as earth continuity at the other end as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make- Starter - Legrand, Crabtree, Anchor, LK

Supply & fixing of BLDC bracket fan 400 mm sweep, input voltage 165-285, RPM 1500 is to be fixed in proper location as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make - Philips, Crompton, Bajaj, Havells

Supply & fixing of fully automatic motor starter 10HP, 7.5kW, overload relay range 8.0A-12A, conforms to IS/IEC 60947-4-4, provided with protection degree IP :54 is to be fixed in proper location as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make- LK , Havells, Crompton, Schneider

Supply & laying of FRLSH PVC insulated 2.5sqmm single core multi-stranded copper 33 cable IS:694 to be laid concealed through suitable size alkathene pipe including 1sqmm single core FRLSH IS:694 multi stranded copper wire is to be used as per direction of Railway Engineer where necessary. Pre-inspection of materials by Railway Engineer should be imparted. Make - Finolex, Havells, KEI, Polycab

Supply & fixing 30W LED street light with pressure die- cast housing along with 16 prismatic polycarbonate diffuser and LEDs with secondary optics and IP 65 protection is to be fixed in proper location as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make : Philips, Bajaj, Crompton, Havells

Fixing of BLDC Ceiling Fan 1200 mm sweep is to be fixed in proper location as per direction of Railway Engineer. (BLDC Ceiling fan will be procured through store).

Supply, installation, testing & commissioning of light point/exhaust fan point (concealed modular) for to be drawn by single core stranded FRLSH insulated 1.5 mm2, 1100 volt grade copper cable conforming to IS:694 through alkathene pipe of suitable size to be fixed inside 26 wall by having final plastering with necessary coupler /elbow /Tee / 4way etc. The point to be terminated by modular type 6A flush type controlling switch on suitable size full/half flash GI board & platinum white plate at one end and by ceiling rose with 1sqmm single core IS : 694 multi-stranded FRLSH copper wire as earth continuity at the other end as per direction of Railway Engineer. Pre- inspection of materials by Railway Engineer should be imparted. Make - Cable- Finolex, Havells, KEI, Polycab C/Rose & Switch - Crabtree, LK, Legrand, Anchor

Supply & fixing of 8 SWG G.I. wire for earthing is to be laid as per direction of Railway Engineer. Pre-inspection of materials by Railway Engineer should be imparted. Make - GI wire : TATA, JINDAL, BANSAL

Supply & erection of HDPE pipe 110mm dia of pressure rating 6.0 kgf/ cm2 (PN -6.0) 6 are to be laid along the pole/ beam/brackets by 25x5 mm MS clamp with required nut, bolt/ washer and under the ground by digging trench of depth 1mtr if necessary. Necessary compression socket and short radius compression bend has to be provided as per direction of Railway Engineer. Pre- inspection of materials by RITES should be imparted. Make- AJAPLAS, SWASTIK, Prime