North Eastern Electric Power Corporation Limited Tender

Dismantling R.C. floor, roof, beans, etc. including cutting rods and removing rubbish as directed withon a lead of 75 m. includingstacking of steel bars. (b) Extra rate for each addl floor over the rate of ground floor.

Removal of rubbish, Earth etc. from The working site and disposal of the same beyond the compound, in conformity with the Municipal/ Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per diection of Engineer in charge.

Hire and labour charges for shuttering with centering and necessary staging upto 4m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works(uptp roof of ground floor) (When the height of a particular floor is more than 4m the equivalent floor height shall be taken as 4m and extra for works beyond the initial 4m ht. shall be allowed under 12(e) for every 4m or part thereof) (a) 25mm to 30 mm thick wooden shuttering as per decision & direction of Enginner-In-Charge.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessay), cutting to requisite lenght, hooking and bending to correct shape, placing in proper position and binding with 16 bending to correct shape, placing proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. (a) For works in foundation and upto roof ground floor/ upto 4m. (i) Tor steel/ Mild steel I. SAIL/TATA/RINL

Ordinary cment concrete (mix 1:1:5:3) with graded stone chips (20 mm normal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (i)Pakur Variety

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar ncluding rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/ staging where necessary (Ground floor). [ Excluding cost of chipping over concrete surface] (iii) With 1:3 cement mortar (a) 20 mm thick plaster

(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

(b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary: (a) On timber or plastered surface: With super gloss (hi-gloss)- (iv) Two coats (with any shade except white)

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary: (b) On steel or other metal surface:: With super gloss (hi-gloss)- (iv) Two coats (with any shade except white)

Applying Acrylic Emulsion Paint of approved make and brand on walls and celing including sand papering in intermediate coats including coats including putty (to be done under specific instruction of Superintending Engineer): (Two coats) ii) Luxury Quality

Dismantling artificial stone flooringupto 50 mm thick by carefullychiseling without damaging the base and removingrubbishas directed within a lead of 75 m (a) In ground floor including roof.

Supplying and laying true to line and level Anti-Skid, Full Body, Homogeneous & Granular finish Vitrified Tiles conforming to IS: 15622-2006 & is 4457-2007 and testing shall be made in accordance with IS:13630 [Non- modular sizes for tiles with Skid resistance 0.5, Mohr's hardness 5.0, Staining resistance: Class-1. Water Absorption: E 0.5%], MOR 35 N/sq.mm in Internal area of building e.g. Toilet Block, passage, Corridor, Accesible Open Terrace etc. set in 20mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sqm or using Polymerised Adhesive (6 mm thick layer applied directly over finished artificial stone floor/ Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per Sqm below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/ epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contractor). b) In Ground Floor: Sizes-600 mm x600mm x10 mm with breaking strength  1500 N

Supplying and laying true to line and level Anti-Skid, Full Body, Homogeneous & Granular finish Vitrified Tiles conforming to IS: 15622-2006 & is 4457-2007 and testing shall be made in accordance with IS:13630 [Non- modular sizes for tiles with Skid resistance 0.5, Mohr's hardness 5.0, Staining resistance: Class-1. Water Absorption: E 0.5%], MOR 35 N/sq.mm in Internal area of building e.g. Toilet Block, passage, Corridor, Accesible Open Terrace etc. set in 20mm sand cement mortar (1:4) and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sqm or using Polymerised Adhesive (6 mm thick layer applied directly over finished artificial stone floor/ Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per Sqm below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles/ epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contractor). b) In Ground Floor: Sizes-600 mm x600mm x10 mm with breaking strength  1500 N Note: Add extra for each addl, floor over the rate above Ground Floor (I) upto 4 th floor- Rs. 12-per Sq.m (II) above 4th floor -Rs. 16/- per Sq.m

Supplying and laying true to line and level High Grip, Scratch resistant, Neutral to UV rays, Full Body Virified Tiles conforming to IS:15622/2006 & IS 4457-2007 and tested in accordance with 1S: 13630 [Non-modular sizes for tiles with Skid resistance: 0.6, Mohr's hardness 7.0, Staining resistance: Class-1, Water Absorption E 0.5%] & MOR 35N/sq.mm and Breaking strength 1500 N for Outdoor area of building e.g. Gang-way, Corridor. Driveway, Parking lots, Courtyards, Sloping ramps, Entrance lobbies, Patios, Portico etc. set over necessary underlay and 2 mm thick cement slurry at back side of tiles using cement @2.91 Kg/Sqm, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles and removal of wax coating of top surface of tiles with warm water and cleaning the tiles using soft and dry cloth complete including the cost of materials, labour and all other incidental charges complete including backside slurry but excluding the cost of underlay and true to the manufacturer's specification and direction of Engineer-in- Charge. In Ground Floor: 300 mm x 300 mm x 10 mm with breaking strength1200N

Supplying, fitting and fixing shower of approved brand and make. (a)(iii)Chromium plated shower arm 240 mm long ( Equivalent to Code No. 536(A) & Model- Tropical/ Sumthing Special of ESSCO opr similar brand)

Supplying, fitting and fixing shower of approved brand and make. (a)(iv) Chromium plated Rose Shower with revolving joint and 150 mm long shower arm ( Equivalent to Code No. 5489 & Model - Florentine of Jaquar or similar brand).

Supplying profiles of required section made of Alumuium Alloy Extrusions conforming to IS: 732- 1983 and IS: 1285- 1975, Anodised ( with required film thickness and specified colour/natural) matt finished conforming to IS: 1868- 1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed/ certified make and brand as per direction of Engineer - in - Charge. ( Payment will be made on finished length of the work ). (A) In 10-12 Micron thickness Annodizing film. 1). Natural White b). 3- track sliding window i). Bottom frame

Supplying profiles of required section made of Alumuium Alloy Extrusions conforming to IS: 732- 1983 and IS: 1285- 1975, Anodised ( with required film thickness and specified colour/natural) matt finished conforming to IS: 1868- 1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed/ certified make and brand as per direction of Engineer - in - Charge. ( Payment will be made on finished length of the work ). (A) In 10-12 Micron thickness Annodizing film. 1). Natural White b). 3- track sliding window ii). Top and side frame

Supplying profiles of required section made of Alumuium Alloy Extrusions conforming to IS: 732- 1983 and IS: 1285- 1975, Anodised ( with required film thickness and specified colour/natural) matt finished conforming to IS: 1868- 1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed/ certified make and brand as per direction of Engineer - in - Charge. ( Payment will be made on finished length of the work ). (A) In 10-12 Micron thickness Annodizing film. 1). Natural White d). Shutter for all track sliding window i). Bottom & Top Member

Supplying profiles of required section made of Alumuium Alloy Extrusions conforming to IS: 732- 1983 and IS: 1285- 1975, Anodised ( with required film thickness and specified colour/natural) matt finished conforming to IS: 1868- 1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed/ certified make and brand as per direction of Engineer - in - Charge. ( Payment will be made on finished length of the work ). (A) In 10-12 Micron thickness Annodizing film. 1). Natural White d). Shutter for all track sliding window ii). Style side member

Supplying profiles of required section made of Alumuium Alloy Extrusions conforming to IS: 732- 1983 and IS: 1285- 1975, Anodised ( with required film thickness and specified colour/natural) matt finished conforming to IS: 1868- 1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed/ certified make and brand as per direction of Engineer - in - Charge. ( Payment will be made on finished length of the work ). (A) In 10-12 Micron thickness Annodizing film. 1). Natural White d). Shutter for all track sliding window iii). Interlock member

Labour charge for fabrication and installation of composite door, window, partitions made from anodised extruded alloy alumunium sections for the following units. (A). Glazed alumunium sliding windows made of extruded and anodized elloy alumunium sections, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and necessary fittings, fixture, adhesives and joineries alongwith extruded neoprine or EPDM gasketting in between window frame and masonry work ( walls, colums beam, lintels etc. ) as well as between glass and shutter frame for fixing slass and polysulphide sealent and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing , specification and direction of EIC. The rate includes the hire charge of all tools and plants, including all incidental charges adhesives, joineries such as screw, cleart angle etc. but excluding the cost of extruded alumunium sections, glass, neophrine/ EPDM gasket, locking arrangement and rollers.

Labour charge for fabrication and installation of composite door, window, partitions made from anodised extruded alloy alumunium sections for the following units. (A). Glazed alumunium sliding windows made of extruded and anodized elloy alumunium sections, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and necessary fittings, fixture, adhesives and joineries alongwith extruded neoprine or EPDM gasketting in between window frame and masonry work ( walls, colums beam, lintels etc. ) as well as between glass and shutter frame for fixing slass and polysulphide sealent and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing , specification and direction of EIC. The rate includes the hire charge of all tools and plants, including all incidental charges adhesives, joineries such as screw, cleart angle etc. but excluding the cost of extruded alumunium sections, glass, neophrine/ EPDM gasket, locking arrangement and rollers. Note : Add extra for each Addl. Floor over the rate of item 2A, 2B,2C and 2D except 2A(vi) i) Upto 4th. Floor

Supplyimg bubble free float glass of approved make and brand conforming to IS: 2835- 1987 ( A ). Clear, toughned glass conforming to IS: 2553- 1992 ( part- II) (i). 6 mm thick

Wash Basin vitreous china -- Continental Wall Hung Toilet Wash Basin with Pedestal CNS-WHT-303 & CNS-WHT-811 of make Jaquar/ Grohe/Kohler or equilavent.

Supplying, fitting and fixing pillar cock of approved make - Florentine sink cock with swinging spout(sink mounted)- FLR-CHR-5357N of make Jaquar/ Grohe/Kohler or equilavent.

Supplying, fitting and fixing towel rail with brackets- Vantage - VEN-4009 Brass Towel Rack with Hook ( Chrome, 600 mm) of make Jaquar/ Grohe/Kohler or equilavent.

Supplying, fitting and fixing E.W.C in white glazed vitreous cjinaware of approved make- Opal Rimless Single piece WC with UF soft close seat cover, hinges, dual flush cistern fitting, fixing accesspries and accessories set. Size 360 X 675 X 750 mm , S - Trap.OPS-WHT-15853S300UF -of make Jaquar/ Grohe/Kohler or equilavent.

Supplying , fitting and fixing of Wash Basin Accessories - ALD-705L130, ZPS-RB07 - f make Jaquar/ Grohe/Kohler or equilavent.

Supplying, fitting and fixing Continental wall mixer with provision for overhead shower with 115 mm long bend pipe on upper side, connecting legs & wall flanges - CON-CHR-273KNUPR.f make Jaquar/ Grohe/Kohler or equilavent.

Supplying, fitting and fixing of 15 litre Capacity Elina Manual Water Heater , 4 Star, White f make Jaquar/ Grohe/Kohler or equilavent.