Municipal Corporation Tender

Anti-termitetreatmenttothejunctionofwoodwork and masonry walls with chemical emulsion by admixingchloropyrofosemulsifiableconcentrates(1% concentration) with water by weight including sprayingat thepoints of contactwith theadjoining masonry by drilling 6m. dia holes at a downward angleofabout45degreeat thejunctionofwoodwork andmasonry and squirting chemical emulsion into theseholesat therateofhalf litreperhole.Theentire workistobecarriedoutasperspecificationofCode I.S.-6313 (Part-III)-1981. The shutters are to be sprayedwith emulsion. on both sides. All wooden fixtures like almirahs, racks etc. are also to be throughly sprayed with chemical emulsion. (Payment will be made on the basis of outside measurements of doors and windows) P-8 Item No-11/d

Spot applicationfor insecticidesusingAquabase spray for pest (for bugs, cockroaches, silverfish, spider, termites,mosquitoes) towallsandceilingetc. with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight including spraying the emulsified chemical@0.5 litresper sq.m. byahandoperated pressure pump onwall surfaces, ceiling, electrical fixture,electrical lines including drilling holes in placeswhere sourceof termite is detected squirting chemical solutionintotheholesandsealingtheholes withcementgrout. (Rateispersq.m.of thefloorarea while actual work will be all walls ceiling, rack, partition and furniture). P-9 Item No-11/e

Dressed wood work in post , plate , battens . etc. fitted & fixed complete (excluding the cost of bolts only, but including the cost of nails, screws etc.) (The quantum should be corrected upto three decimals (iii) Sal : Malayasian P-135 ItemNo-1/B/iii

Supplying solid flush type doors of deluxe decorative (both side) quality, conforming to I:S 2202 timber frame consisting of top and bottom rail and side styles of well seasoned timber 65mm wide each and the entire frame fitted with 27.5mm wide battens places both ways in order to made the door of solid core and internal lipping with teak, mahogony or rose wood approved decorative veneers using phenol formaldehyde as glue etc. complete, including fitting, fixing the shutters in position but excluding the cost of hinges and other fittings in ground floor: (a) 35mm thick shutters (single leaf) P-124 Item No-12/a

Supplying, fitting and fixing boiling water resistant ply conforming to IS: 303-1989 bonded with phenol formaldehyde synthetic resin of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in-Charge.[excluding the cost of supporting frame work and teak wood batten/Lipping] In Ground Floor (ii) 6mm P-173 Item-3/ii P.W.D Building

Supplying, fitting and fixing boiling water resistant ply conforming to IS: 303-1989 bonded with phenol formaldehyde synthetic resin of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in-Charge.[excluding the cost of supporting frame work and teak wood batten/Lipping] In Ground Floor iv) 12mm P-173 Item-3/iv P.W.D Building

Supplying fitting, fixing decorative lamination conforming to IS: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on Particle/MDF / Ply Boards with recommended / approved adhesive with proper clipping the sides for better attachment as per direction of Engineer-in-charge.The rate includes the cost of labour, adhesive and all incidental charges thereof. In ground floor Glossy/Matt/Suede excluding surface texture or metallic lustre. (i) Thickness of laminate 1.5mm P-179 Item-14/i P.W.D Building

French polishing to wood work including preparing surface (ordinary gloss) (a) On new wood work P-202 Item-11/a P.W.D Building

Supplying, fitting and fixing Godrej Multi Lock or equivallent . P-147 Item No-39 P.W.D Building

Scantling upto 50mm wide and 12mm thick (chamfering or rounding) for ceiling/partion battens including fitting, fixing in position with washers, coach screws etc. complete.: Sishu / Champ / Badam / Gamar / Bhola / Mogra / Hallak P-137 Item No-7/b P.W.D Building

Supplying and laying true to lineand level vitrified tiles of approved brand (size not less than 600mmX600mmX10 mmthick) in floor, skirtingetc. set in 20mm sand cement mortar (1:4) and 2mm thick cement slurry backside of tiles using cement@2.91Kg./sq Morusing polymerised adhesive (6mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using1.75Kg of cement per sqM below mortar only, joints groutedwithadmixtureofwhite cement andcolouringpigment tomatchwithcolourof tiles / epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement,syntheticadhesiveandgroutmaterial tobesupplied by the contrr]e) I With application slurry@1.75kg/ Sq.m, 20mm sand cement mortar(1:4) &2mm thick cement slurry at backside of tiles, 0.2 kg/ Sq.mwhite cement for joint filling with pigment. Deep Colour & White P-66 Item No-36/I/A P.W.D Building

Removing old paint from blistered painted surface of steel or other metal by chipping including scraping and cleaning and exposing the original surface. p-203, Item no-3 P.W.D Building

M.F. suspended ceiling made with 12.5 mm thick Gypsum plaster board including G.I. perimeter channel of 0.55 mm flush (having two flanges 20 mm and 30 mm respectively and web 27 mm ) along with perimeter of ceiling with G.I. intermediate channel of 0.9 mm thick size 45 mmx15mm placed at 750 mm c/c with G.I. ceiling angle of size 25 mmx10mmx0.55 mm thick fixed to the ceiling with G.I. Cleat and steel expansion fastener ceiling section 0.55 mm thick of size 51.50 mmx26mm fixed to the intermediate channels with the help of connecting clip and in the direction of perpendicular to the intermediate channel of 300 mm c/c 12.5 mm thick Gypsum plastered board are to be fixed under ceiling section as above by machine screws. The oards are to be joined and finished with jointing compound, paper tape and application of top coat etc. as per the direction of Engineer-in-charge. (The rate includes of cost of all materials including taxes, cost of accessories, fittings and fixtures, scaffolding and labour charges etc. complete) In ground floor P-165 Item-17 P.W.D Building

Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface toreceive Distemper/ Acrylic emulsion paint including scrapingand preparing the surface throughly, complete as permanufacturer's specification and as per direction of the EIC. (In Ground Floor) (a) One Coat ii) Solvent based interior grade Acrylic Primer Page No-195 Item No-7/a/ii P.W.D Building

Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface. Two Coats Page No-196 Item No-10 P.W.D Building

Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized(with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer- In-Charge. (Payment will be made on finished length of the work). (A) In 10-12 Micron thickness Annodizing film I) Natural white b) 3- track sliding window i) Bottom frame P-233 Item No-1/A/b/i

Supplying profiles of required section made of Aluminium Alloy Extrusions conforming to IS: 732-1983 and IS: 1285- 1975; Annodized(with required film thickness and specified colour / natural) matt finished conforming to IS: 1868-1983 for fabrication of composit door, sliding & casement windows, partitions, formed of basic sections of any ISI embossed / certified make and brand as per direction of Engineer- In-Charge. (Payment will be made on finished length of the work). (A) In 10-12 Micron thickness Annodizing film I) Natural white b) 3- track sliding window ii) Top and side frame P-233 Item No-1/A/b/ii

d) Shutter for all track sliding window. i) Bottom & Top member. Page No-233 Item No-1/A/I/d/I P.W.D Building

d) Shutter for all track sliding window. ii) Style side member. Page No-233 Item No-1/A/I/d/ii P.W.D Building

Supplying PVC rollers for sliding windows as per direction of Engineer in charge. P-242 Item No-6 P.W.D Building

Supplying EPDM gusket of approved make and brand as per direction of Engineer in charge. For sliding windows 'U' shaped EPDM gasket for frames. P-242 Item No-8/i/b P.W.D Building

Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987. ii) 4mm thick coloured / tinted / smoke glass. p-243 Item No-9/ii P.W.D Building

(F) Supplying Zinc powered coated star lock (Natural White) Page No-244 Item No-13/f P.W.D Building

Labour charge for fabrication and installation of composite door, window , partitions made from annodized extruded alloy aluminium sections for the following units:- (A) Glazed aluminium sliding windows made of extruded and annodized alloy aluminium sectios, fabrications, including cutting to proper shape and size, drilling and aligning of window shutter frame fitted with in built locking arrangements, sliding rollers and other necessary fittings, fixture,adhesives and joineries along with extruded neoprine or EPDM gasketing in between window frame and masonry work (walls, column, beam.lintels etc.) as well as between glass and shutter frame for fixing glass and Polysulphide sealant and in between shutter and window frame where necessary including cutting to requisite size and fixing glass as per drawing, specification and direction of EIC. The rate includes the hire charge of all tools and plants, including all incidental charges, adhesive, joineries such as screw, cleat angle etc. but excluding the cost of extruded aluminium sections, glass, neoprene / EPDM gasket, locking arrangement and rollers. i ) 2 track sliding window. P-239 , Item No-2/i P.W.D Building

(b) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. p-200, Item no-1/a P.W.D Building

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary On steel or other metal surface Two coats (with any shade except white) P-200 Item-2/A/b/iv

Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: (a) With continuous plate base (Hexagonal/ Round rod) (iii) 100 mm grip x 12 mm dia rod. P-145 Item-30/a/iii

Supplying 'Godrej' mortice lock chromium plated with keys 6 levers including fitting & fixing complete. P-143 Item-16/b

Door stopper.(Brass) P-143 Item-19/i

Godrej Hydraulic door closer fitted and fixed complete. (a) Heavy type P-143 Item-23/ii/a

Anodised aluminium butt hinges of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 205/66) and fitted and fixed with cadmium plated screws: 100 x 63 x 3.2mm P-145 Item No-29/v

Supplying Mazdoor (Male) p-303 item no-3

Diaper rod with decorative holder. Market Rate

Window Curtain. Market Rate

Add @ 18% GST

Add @ 1% Labour Cess