Municipal Affairs Department Tender

Providing and laying bituminous macadam with Mobile Hot Mix Plant (Light Duty) using approved crushed aggregates of specified grading as per Table 500.7 premixed with bituminous binder , transported to site laid over a previously prepared surface at specified laying temperature by means of approved and suitable arrangements to the required grade , level and alignment and rolled with suitable power roller for break down , inter- mediate and finished rolling as per specification to achieve the desired compaction including cost and carriage of stone materials and bitumen , hire charges of machinary and equiptment , cost of fuel and lubricants and wages of operational staff , quality control complete as per Specifications for Road & Bridge Works of MoRT&H (5th Revision).

Providing, laying and rolling of Open - graded premix surfacing of 20 mm thickness composed of 13.2 mm (@ 0.018 m³ per m²) and 11.2 mm (@ 0.009 m³ per m²) size stone aggregates, including thoroughly cleaning of the surface, screening, cleaning and pre-heating stone chips and fully pre-coating the same either using viscosity grade paving bitumen or cut-back or emulsion, carrying the mixture by any suitable arrangements,laying the mixture uniformly over the surface, including line, grade and level to serve as wearing course on a previously prepared base, including mixing in Mobile Hot Mix Plant (Light Duty) and thoroughly rolling with a smooth wheeled roller 8-10 tonne capacity, finished to required level and grades including the cost and carriage of stone chips and matrix, heating the matrix, preheating the aggregates to required temperature and including the hire charges of Mobile Hot Mix Plant (Light Duty) and other machinery, pay of operators, cost of fuel and lubricants etc. complete to be followed by seal coat of either Type A or Type B as per Technical Specification Clause 508 for Rural Roads of MORD.

Providing and laying Premixed Seal Coat (Type B) with approved quality sand/grit @ 0.6 m3/ 100 m2 and bitumen binder on thoroughly cleaned black top surface coated with tack coat, including heating and mixing cleaned sand/grit (100 % passing through 2.36 mm sieve and retained on 180 micron sieve) uniformly with bitumen binder, laying and spreading the mix at an uniform rate using suitable means, brushing the surface, if necessary, to ensure uniformity, followed by rolling with power roller including the cost and carriage of binder and aggregates, cost of heating the binder and aggregates and all other incidental charges, cost of fuel and lubricants, including hire charges of machineries, tools & plants required for construction and quality control complete as per Clause 511 of Specifications for Road & Bridge Works of MoRT&H (5th Revision) By Manual Means (II) With Hot Bitumen Binder (@ 6.80 kg / 10 sqm.) Labour rate per sq.m. area a) On freshly laid premixed surface without Tack Coat Stone Grid

Ordinary cement concrete (mix1:2:4) M-15 with graded stone chips( 20mm.size)excluding shuttering and reinforcement if any,in ground floor as per IS 456-2000 a) Pakur/Chandi variety (P-12, I.no.-5(a)

Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand.

(B) Filling in foundation or plinth by fine sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. For Drain & Road :-

Brick work with 1st class bricks in cement mortar(6:1) In foundation and plinth.

Plaster ( to wall,floor,ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints or roughening of concrete surface by chamfering etc. including throating,nosing and drip course where necessary ( Ground floor): With 4 : 1 cement mortar b) 15mm. Thick plaster

Neat cement punning about 1.5 mm thick in wall,dado,window, sills, floor, drain etc.

Add 18% GST

Add 1.0% Cess