Municipal Affairs Department Tender

Page No.-24, Item No.- 4(a) Ordinary cement concrete (mix 4:2:1)) with grade stone chips (20mm down excluding shuttering and reinforcement. If any in ground floor as per relevent IS Codes (a) Pakur Variety

Page No.-15, Item No.- 8 Brick work with 1st class bricks in cement mortar (1:6) (a) In foundation and plinth

Page No.-189, Item No.- 1 Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (i) With 1:6 cement mortar (a) 25 mm thick plaster

Page No.-192, Item No.- 15 Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m

Page No.-42, Item No.- 36 Hire and labour charges for shuttering with centering and necessary staging upto 4m using approved stout props and thick hard wood planks of approved thickness with required braching for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of work.(upto roof of ground floor) (f) 25 mm to 30 mm thick wooden shuttering without staging in foundation.

Page No.-103, Item No.- 8 M.S. works in brackets made from flats, angles, tees etc. to sizes specialy bent, twisted, forged; making holes drilled and fitted to rafter of trusses with necessary bolts, nuts, washer or screws etc. (length of straight not less than 230 mm)

Page No.-99, Item No.- 01 M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length,fabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section,consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. I) For structural members of specified sections weighing less than 22.5 Kg./m

Page No.-82, Item No.- 14 Supplying, fitting & fixing Zn-Al alloy (55% Al & 45% Zn) coating of 150 grams per sq. metre (followed by colour coated on both side) steel sheet work having minimum yield strength of 550 Mpa of trapizoidal profile of approved make (excluding the supporting frame work) fitted and fixed with 55 mm & 25 mm self tapping screw, EPDM Washer 16 mm dia & 3 mm th. washer etc. complete with 150 mm end lap and one corrugation minimum side lap. (Payment to be made on area of finished work). In Roof:- a) With 0.5 mm thick sheet

Page No.-200, Item No.- 1 (b) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc.

Page No.-200, Item No.- 2 (A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface : With super gloss (hi-gloss) - With other than hi-gloss of approved quality- (iv) Two coats (with any shade except white)

ADD 18 % GST

ADD 1% CESS