Municipal Affairs Department Tender

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. (a)    Pakur/Chandil variety. (P.No.26 T/10(i)), 3rd corrigenda,

Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. (P-11, T/10))

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course,scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] Page No.189,Item No.-1 (ii) With 1:6 cement mortar (A) 10 mm thick plaster (Inside plaster)

With 1:6 cement mortar (a) 15 mm thick plaster (Outside plaster)

With 1:6 cement mortar (a) 20 mm thick plaster (Inside plaster)

Scraping of moss, blisters etc.thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc.(Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge) (P.No.198, T/1)

(a) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. (P-200,I. T/1 a)

(b) Priming one coat on timber or plastered surface with synthetic oilbound primer of approved quality including smoothening surfaces by sandpapering etc.

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. Including using of approved putty etc. on the surface, if necessary : (P-200, T/2 b, iv) (b) On steel or other metal surface : With super gloss (hi-gloss) - (iv) Two coats (with any shade except white)

(A) Painting with best quality synthetic enamel paint of approved makeand brand including smoothening surface by sand papering etc. includingusing of approved putty etc. on the surface, if necessary : (P-200, T/2 a, iv) (a) On timber or plastered surface : With super gloss (hi-gloss) - (iv) Two coats (with any shade except white)

Applying Interior grade Acrylic Primer of approved quality and brandon plastered or cencrete surface old or new surface to receiveDistemper/ Acrylic emulsion paint including scraping and preparingthe surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor) i) Water based interior grade Acrylic Primer one coat (P.195, T/7 (i))

Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer's specification) including cleaning and smoothning of surface. (P-196, T/10)

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. In Ground Floor: (a) One Coat (P-196, T/8(a))

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. Two Coats In Ground floor (Two Coat) a) Normal Acrylic Emulsion (P-19, T/17(a))

M.S. structural works with hollow sections (square or rectangularshape) conforming to IS: 806-1968 & IS:1161-1998) connected toone another with bracket, gusset, cleat as per design, drawing &direction of Engineer-in-Charge complete including cutting to requisite shape & size, fabrication including metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting anderection all complete. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools and plants and labour reqired for execution and all incidental chages (such as electricity, labour insurance) etc. complete.Payment to be made on the basis of calculated weight of structuralmemebrs of MS Holow Section as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made byadding the actual weight of such items with weight of finishedstructural members. The rates are considered for a hight of erection 8 m. / 2nd floor level from the ground. Add 1.5 % extra over the ratefor each additional floor or 4m. beyond the initial 8 m. or part thereof. additional floor or 4m. eyond the initial 8 m. or part thereof. (P.No.100, T/2 ) i) For trusses spanning up to 12.00 m 60 mm.X 60 mm X 4 mm

40 mm.X 40 mm X 4 mm

Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work)(GCI sheet to be supplied by contractor) (P.No.81, T/9 (i), (b) b) With 0.63 mm thick sheet

Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, alamoid /Bitumen /M-Seal etc) complete. (P-212, T/21 a, c, d ii) Plumbing & Sanitary Schedule 2017 A) UPVC Pipes: (ii) 75 mm. Dia.

B) UPVC Fittings: c) Bend 87.5 degree (i) 75 mm. Dia.

d) Shoe (ii) 110 mm. Dia.

Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. bIn ground floor. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement). Using grey cement (Add extra @1.5% for each addl. floor upto 4th floor and @1.75% for each additional floor above 4th floor for item. No.5 and 6 of subhead A). (ii) 25 mm. thick , page no -48,item-6/ii

M.S. structural works in columns, beams etc. with simple rolledstructural members (e.g. joists, angle, channel sections conformingto IS: 226, IS: 808 & SP (6)- 1964 connected to one another withbracket, gussets, cleats as per design, direction of Engineer-inchargecomplete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming toIS: 816- 1969 & IS: 1995 using electrodes of approved make andbrand conforming to IS:814- 2004, haulage, hoisting and erectionall complete. The rate includes the cost of rolled steel section,consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including allincidentalchages such as electricity charges, labour insurance charges etc.Payment to be made on the basis of calculated weight of structural members only in finished work as per IS specified weight. Paymentfor gusset, bracket, cleat, rivets, bolts and nuts may be make byadding the actual weight of such items with the weight of finishedstructural members or 7% of weight for finished structural membersweighing not less than 22.5 Kg. / m. or 15 % of weight for finishedstructal members weighing less than 22.5 Kg. / m. may be increasedallow for bracket, cleat, rivet, bolts and nuts etc. and no seperatepayment being made for these items, as per direction of Engineer InCharge. The rates are considered for a height of erection 8m. / 2nd floor level from the ground. Add 1.5% extra over the ratefor each additional floor or 4m. beyond initiial 8m. or part thereof.I) For structural members of specified sections weighing less than 22.5 Kg./m (P.No. 99,T/1) 3RD CORRIGENDAM M.S ANGLE (40mm X 40mm X 5mm)

Square or hexagonal mesh netting made with 18 B.W.G. galvanised wire, fittedand fixed complete as per design (excluding the supporting framework but including local sal wood battens of size 37.5mmx25mm). In ground floor. (a) 19mm mesh. (P.138, T/10/a)

(a) Supplying, fitting galvanised 3 ply 12 gauge / 4 points line ofbarbed wire in fencing (holes already made in the body of the post)or fixed by staples tightening and fixing the wires in taut conditionwith straining bolts including the cost of cutting and of lappingjoints in the wire as necessary but excluding the cost of galvanised staples,straining bolt and binding wire where necessary. (P.219, T/2/a)

Drilling holes of requisite diameter in R.S. joists channels, tees.Plates etc. (a) (I) Dia. Upto 12mm and depth upto 10 mm. (P.102, T/4(a))

Supplying, fitting, fixing bolts with nuts, washer: (i) 10 to 16 mm dia: (a) Length up to 75 mm (P.103, T/7i(a)

Supplying and laying chequered tiles of any shade & of approved quality with (1:1½:3) cement concrete laid in panelsor patterns as directed in pavement, footpath etc. includingnecessary underlay 25 mm thick [avg] cement mortar (1:3)complete in all respect with all labour and materials. [Usingcement slurry @ 4.4 kg/Sq.m at back side and @2.4 kg/Sq.m for joint filling] Red Variety ; ii) 30 mm. thick (P.74, T/46)

Installation of Falak 600 mm x 600 mm Quoted Rate

Add GST @ 18%

Add Cess 1%