Municipal Affairs Department Tender

Laminate finished Storage / Side Unit etc. made with BWR quality Block Board and Ply and inside complete with french polish. All the edges over teak wood bead and as per direction of Engineering In Charge. (mode of measurement - length X height)

Supply, fitting, fixing multiple Wooden seating arrangement with continuous Desk made with Teak wood frame structure and molding bead in all the edges / sal wood in supporting members and corners covered with veneer over BWR ply. Seats are with best quality upholstery with approved fabric as per design radially start to end in a block having pull out writing desk and all complete with hi-gloss French polish as per direction of Engineering in Charge.

Decorative work in Front partition over veneer made with Teak Wood batten , molding bead , ply , veneer and finally finished with high gloss french polish as per direction of Engineering in Charge

Supply, fitting, fixing multiple Wooden seating arrangement made with Teak wood and sal wood in supporting members. Seats are with best quality upholstery with approved fabric as per design radially start to end (approx. 3M long bench type with back rest) and all complete with hi-gloss French polish as per direction of Engineering in Charge. (in Council Hall)

Supply of Wooden Decorative Chair made with Teak Wood, with two nos Hand rest. Seat and back covered with high density rubber and foam wrapping complete with quality fabric after polish finish complete in all respect as per direction of Engineering In Charge. (for Councill Hall 4)

High Back Wooden decorative Chair with arm and best quality upholstery with quality fabric after polish finish complete in all respect as per direction of Engineering In Charge. (for Councill Hall - 3 & Chairman - 1)

Supply of Single Seater manual Recliner Sofa (Size - 0.86 W X 0.92)

Throne chair - made with Mahogany Wood having wood curved design, with two nos. Hand rest. Seat and back covered with hi density rubber and foam wraping complete with approved fabric after polish finish cpmplete in all respect as per direction of Engineering In Charge

Revolving chair (High Back) with PU padded adjustable Armrest for Officers - Seat Cushion with Molded PU Foam with Leatherette backrest with Wt Sensitive multi position locking as per direction of EIC

Three seater Sofa with Soft PVC upholstery over high density Foam as per direction of Engineering In Charge. (For Chairman's Room only)

Single seater Sofa with Soft PVC upholstery over high density Foam as per direction of Engineering In Charge. (For Chairman's Room only)

Wooden Designer Center Table polish finished complete as per direction of Engineering In Charge. (Council Hall Lounge -2 and Chairman's Chamber-1)

Wooden Side Table/ Corner Table (0.45 X 0.45) polish finished complete as per direction of Engineering In Charge. (in Councillor Lounge)

Wooden Designer Side Table/ Corner Table (0.6 X 0.6) polish finished complete as per direction of Engineering In Charge.

Visitor's Chair - Strong SS tubular Metal frame chair with PP Armrest, PVC upholstered Seat and Back as per direction of EIC. (Councillor Lounge - 30 and Chamber - 5)

Perforated Stainless Steel chair - Three in a Set in Lobby

Carpet - Supplying and Fixing of MADE IN INDIA broadloom carpet of WELSPUN MAKE,100% Nylon LOOP Pile, Printed, Pile Height 7 mm (± 1 mm),Total Height 9 mm (± 1 mm),Stitch / 10 cm 39 (± 2% ), Pile Weight Net less Than 590 GSM (± 5% ), Total Weight 1381 GSM (± 5% ), Secondry Backing PP Mesh, Gauge 1/8 Cut Pile, Latex Natural Rubber, Color fastness to LightTest Method: AATCC 16 (20 AFU) ≥ 4.0 at 80 Hours , Static Electricity Test Method: AATCC 134 Less than 3.5 KV, Hexapod test Method: ASTM D 5252 ≥ 4,Flammability (Radiant Panel) Test Method: ASTM E 648 ≥ 0.45 (Class I) , complete as per drawing , specifications of the architect. The carpet and Underlay (min 6 mm) will be installed with standard Adhesives and as per direction of Engineering-In-Charge

Supplying, fitting and fixing 8 mm thick Laminated wooden Flooring Work conforming to EN13329:2006 with plank size not Iess than 1200mmX 190 mm (with unilin/tongue-groove locking arrangement) having 0.2mm thk top abrasive layer over a decorative layer followed by a High-density fibreboard (HDF) having density 940 kg/m3 substrate core over a rasin saturated backing layer and installing through unilin or tongue- groove system (having locking strength not less than 1000 kg/m) over a 2 mm thk underlayer polyurethene foam on polythene sheet 250 micron, over a smooth, flat, hard subfloor free from moisture ( 8%), grease etc. complete in all respect with requisite accessories like end profile, transition profile, reducer 'T' profile etc. wherever required and preparation of base including all other incidental works as per direction & satisfaction of Engineer in charge. Cost of Laminate Floor Accessories only (Skirting,End edge, T- moulding,Reducer) shall have to be added separately, wherever required

Supplying Laminate Floor Accessories (Skirting, End edge, Tmoulding, Reducer ) to 8mm thick Laminated wooden Flooring Work conforming to EN13329:2006 with plank size not Iess than 1200mmX 190 mm (with unilin/tongue-groove locking arrangement) having 0.2mm thk top abrasive layer over a decorative layer followed by a High-density fibreboard (HDF) having density 840 kg/m3 substrate core over a rasin saturated backing layer and installing through unilin or tongue- groove system (having locking strength not less than 1000 kg/m) over a 2 mm thk underlayer polyurethene foam on polythene sheet 250 micron, over a smooth, flat, hard subfloor free from moisture ( 8%), grease etc. complete in all respect as per direction & satisfaction of Engineer in charge. Cost of labour charge for fitting & fixing of Laminate Floor Accessories only (Skirting,End edge, T- moulding,Reducer) shall have to be added separately, wherever required. (Note: This work should not be executed without specific permission of Superintending Engineer)

Podium - Supply, fixing Wooden Podium made with 19 mm BWR ply covered with Veneer and finished with Hi gloss french polish as per direction of Engineer In Charge. (Council Hall - 2 nos & Councillor Lounge - 1)

Tables on Dias in Council Hall - Supply, fixing Wooden Table made with Teak wood frame structure with 4 nos decorative Leg and molding bead in all the edges and corners covered with BWR ply and approved veneer as per design complete with french polsh as per Direction of Engineering In Charge. a) Size - (1.8 X 1.1)

Tables on Dias in Council Hall - Supply, fixing Wooden Table made with Teak wood frame structure with 4 nos decorative Leg and molding bead in all the edges and corners covered with BWR ply and approved veneer as per design complete with french polsh as per Direction of Engineering In Charge.b) Size - (1.8 X 1.2)

Tables on Dias in Council Hall - Supply, fixing Wooden Table made with Teak wood frame structure with 4 nos decorative Leg and molding bead in all the edges and corners covered with BWR ply and approved veneer as per design complete with french polsh as per Direction of Engineering In Charge.c) Size - (2.7 X 0.75)

Tables on Dias in Council Hall - Supply, fixing Wooden Table made with Teak wood frame structure with 4 nos decorative Leg and molding bead in all the edges and corners covered with BWR ply and approved veneer as per design complete with french polsh as per Direction of Engineering In Charge.d) Size - (0.5 X 0.9)