Kalyani University Tender

CPU trolley - with castors

KBPT with mousetray - Metal

PENTA + RECTA WORKSTATIONS - 1500 X 1500 X 600 & 900X 600 Providing and placing "UPBEAT"desk based modular workstation with System ht - 1050 mm. PARTIAL SCREENS: Fabric T- mould, 19mm thk Screen of 300mm ht.,mounted on Studs. LEGS: Providing metal powder coated Dfine Plus leg. Legs are for standard workstation height of 750mm. UNDERSTRUCTURE: Comprising of metal powder coated cross connectors between legs and legs. Made up of metal powder coated finish and the entire assemply is fixed to the worktop. WIRE MANAGEMENT: For 750 high workstations- For vertical wiremenagement, Shared legs with cover are considere. For horizontal wiremanagement - Wire Tray with integrated power box. Access flap will be provided. Switch plate of (8+3 Anchor Roma) module is considered for Power and Data points. WORKSURFACE - Out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500X1500X600 & 900X600 MODESTY : Metal modesty: Lazer cut perforated Metal modesty Metal and wooden modesty are mounted on the worktop with the help of the modesty mounting brackets Modesty terminates at 400 mm from ground.

Pedestals with legs - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file.

CPU trolley - with castors

KBPT with mousetray - Metal

LAB BENCH SYSTEM in Research Lab Room 1st Floor Providing D-Frames manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout.Horizontal Members are made from square pipes of 1.6 mm thickness. Cross-sectional dimensions of the pipe should be 30 x 30mm with a minimum of 1.6 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two D-Frames together as shown using C-clamps/U-clamps. Together with the D-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent D-Frames. They should be available in various widths of 450, 600, 1050, 1200, and 1500 (i) TABLE ADDON 1200W-750D-900H

(ii) TABLE ADDON 1500W-750D-900H

(iii) TABLE ADDON 600W-750D-900H

(iv) TABLE MAIN 1050W-750D-900H

(v) TABLE MAIN 1200W-750D-900H

Providing Under bench cabinets which are Pure epoxy powder coated with thickness of 40-60 microns and will be suspended from tubular structure. The cabinet will have a corrosion resistance magnetic strip as shutter catch, shutter and drawer are to be equipped with 180 degree cam lock. PP constructed semi recessed handle to be screw fitted to the shutters. Hinges are of SS-304 knuckle overlay type with 270 degree opening and 2 nos of hinges are to be screw fitted to each shutter and cabinet. Unit Construction : It will be Welded body construction with load bearing members such as top, bottom and stiffeners should have a minimum thickness of 0.8 mm and drawer separator should be of 1.2mm thick. Shelf : Will be made of 0.8mm thickness which should be adjustable to 6 steps of 50mm. Shutter will be over-closing type. It has a sandwich door construction with shutter front & shutter cover with 1.2mm thick hinge stiffener. Empty gap should with filled with 15mm thick paper honeycomb for sound dampening. Drawer: Will be welded single piece construction with over-closing sandwich drawer front filled with 15mm thick paper honeycomb for sound dampening. Units will be in 450mm and 600mm widths. (i) UNDERBENCH CABINET 450W-450D-674H 1S 1D LH

(ii) UNDERBENCH CABINET 600W-450D-674H 2S 1D

Providing and supply of Welded Top Units :Over head cabinets are Pure epoxy powder coated with thickness of 40-60 microns and should be fixed on the wall. The cabinet will have a corrosion resistance magnetic strip as shutter catch, shutters are to be equipped with 180 degree cam lock. PP constructed semi recessed handle to be screw fitted to the shutters. Hinges are of SS-304 knuckle overlay type with 270 degree opening and 2 nos of hinges are to be screw fitted to each shutter and cabinet. Unit Construction : It will be Welded body construction with load bearing members such as top, bottom and stiffeners should have a minimum thickness of 0.8 mm. Shelf : will be made of 0.8mm thickness which should be adjustable to 6 steps of 50mm. Shutter will be over-closing type. It has a sandwich door construction with shutter front & shutter cover with 1.2mm thick hinge stiffener. Empty gap should with filled with 15mm thick paper honeycomb for sound dampening. Units will be in 450mm and 600mm widths. (i) WALL CABINET 450W-320D-674H 1S LH

(ii) WALL CABINET 600W-320D-674H 2S

All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating (i) LEG SPACE PANEL SET 600W-900H

(ii) LEG SPACE PANEL SET 900W-900H

All leg-space panels, rear cover panels, island side panels etc. should be made from CRCA MS panels of minimum 0.8mm thickness with pure epoxy powder coating (i) REAR SIDE PANEL SET 750D-900H

Providing D-Frames manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout.Horizontal Members are made from square pipes of 1.6 mm thickness. Cross-sectional dimensions of the pipe should be 30 x 30mm with a minimum of 1.6 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two D-Frames together as shown using C-clamps/U-clamps. Together with the D-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent D-Frames. They should be available in various widths of 450, 600, 1050, 1200, and 1500 (i) CORNER TABLE DOOR FRAME 900H

(ii) CORNER TABLE CABINET FILLER PANEL FOR CABINET 900H

(iii) CORNER TABLE PIPE FRAME 750D-900H

Providing and supply of electrical trunking: Using for housing electrical switches and sockets, its top panel, bottom panel of the trunking should be made from minimum of 0.8mm thick body. It should be available in both, single sided and double-sided configurations. It should be made from CRCA MS with pure epoxy powder coating. The front surface that houses the electrical points should have a slope. (i) Table Mounted Trunking

Providing D-Frames manufactured from standard hollow metal sections; confirming to I.S. Code 7138:1973 (Indian Standard specification for steel tubes for furniture) and all sheet metal components should be of CRCA confirming to IS Code 513:1994. The suspended under-bench welded units should be supported on heavy-duty steel frames fully carrying the load of worktops. Its superior strength combined with aesthetically appealing end caps shall give maximum flexibility and modularity while making a layout.Horizontal Members are made from square pipes of 1.6 mm thickness. Cross-sectional dimensions of the pipe should be 30 x 30mm with a minimum of 1.6 mm. They should be made of CRCA MS and coated with pure epoxy powder. These connect two D-Frames together as shown using C-clamps/U-clamps. Together with the D-Frames and Horizontal Members connected together, the skeletal structure of the work-bench is formed on which the worktop can be placed and the hanging-type storage cabinets can be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent D-Frames. They should be available in various widths of 450, 600, 1050, 1200, and 1500 (i) SIDE PANEL FOR SINK UNIT

(ii) INLINE SINK UNIT 750W x 750D x 900H

Providing and supply of Sink, Faucets & Accessories: Polypropylene moulded sinks are made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Standard bowl size (L x W x D) is 500 x 400 x 300 mm. Faucet shall be 3-way or 1-way type faucet of approved make. Service fittings are of laboratory grade, and water faucets and valve bodies are of cast red brass alloy or bronze forgings, all fittings are of powder plated unless specified otherwise. (i) Pp Drop-In Sink Model S 06 560 Mm (W) X 355 Mm (D)

Providing and supply of Sink, Faucets & Accessories: Polypropylene moulded sinks are made up of 5 mm thick high density and elastic poly propylene with good resistance to organic solvents. Standard bowl size (L x W x D) is 500 x 400 x 300 mm. Faucet shall be 3-way or 1-way type faucet of approved make. Service fittings are of laboratory grade, and water faucets and valve bodies are of cast red brass alloy or bronze forgings, all fittings are of powder plated unless specified otherwise. (i) 3 Way Water Faucet Bench Mounted, 8"" Swing Gooseneck Model No. 100/32

Providing and supply of Granite Work Top : It shall be 19mm (+/- 2mm) thick Jet Black Granite worktop. The exposed edges of the worktop shall be chamfered and smoothened. The bottom of the worktop shall be polished and there shall be a V-groove throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30 mm at the sides. The backing material used is a neoprene mat of 6 mm thickness. (i) Jet Black Granite (Sq.Mt.) 20 (±2) Mm Thk

(i) 6 MM Self Adhesive Natural Rubber Strip

(ii) Silicon Sealant - Black

(iii) Masking Tape

(iv) 16A, 1 Way Switch - Model No: M0130

(v) Anti-Siphon Bottle Trap Model : S 04 Make: Premier

(vi) Flexible/F Serated Connector Model : Hp 01 Make: Premier

Providing and supply of Electrical accessories 6/16A, 6 Pin Shutter Socket - Model No: M1332