Jadavpur University Tender

iii) Glazing clip.

Labour charge for fabrication and installation of composite door,window, partitions made from annodized extruded alloy aluminium sections for the following units:- iv) Fixed glazing [Item 2 iv Page No 239]

Wall panelling / partition with Melamine faced 3 layered flat pressed wood particle board of approved make and brand as per direction of EIC of requisite grade bonded with phenol formaldehyde synthetic resin conforming to IS: 848 - 1974 (excluding the cost of supporting frame work and teak wood battens / lipping) 12mm thick [Item 1/B/ii/a Page No 172]

k) Movable door shutter. i) Door frame. (Top & sides). [Item 1/A/i/k/I Page No 236]

ii) Shutter ………... PCS [Item 1/A/1/k/ii page- 235

Top rail.

Bottom rail.

Lock rail

Door vertical.

Glazing cleap.Plaster (to wall ,floor, ceiling etc.) with sand cement….where necessary(ground floor) (a) 20 mm thick plaster PCS [Item - 1 page -189

Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units:-ii)openable/ Casement window PCS-I [Item 1(A)(I)(K)(i) ] page 235

Supplying EPDM gusket of approved make and brand as per direction of Engineer in charge. i) For sliding windows [Item No. 8/a/iii Page No. 242]

i) For sliding windows b) 'U' shaped EPDM gasket for frames.

iii) weather gasket / wool pile for door vertical.

Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987; (A) clear, toughened glass conforming to IS: 2553-1992 (part-II) (ii)8 mm thick PCS [Item- 24(A) page-249

Supplying heavy duty hydraulic double action floor spring along with top pin/set of pivots conforming to IS: 6315 or any approved make as per direction of EIC. PCS item 3 page 242

fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300mm c/c. The Main Runners to be placed @ 1200 mm. The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm X 600mm. Additional Cross Tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600 mm X 600 mm. Grid of module size 600 mm X 600 mm shall be supported by 6 mm dia G.I. wire from purlins / soffit. 15mm thick OW Acoustic Board (Mineral Fiber Acoustic Ceiling Tiles) of approved patern and size 595mm X 595mm with NRC value 0.65 should be placed in he Grid module to form a False Ceiling. All complete as per the drawing & directions of Engineer-in-charge. In ground floor. a) Acoustic False Ceiling (with 15mm thick OW Acoustic Board and E-Grid U- 1520). PCS Item 1 , Page - 162

Rendering the surface of wall & ceiling with white cement based wall putty. Page 204/5,b

(B) Supplying 125 mm. Dia acrylic handle for aluminium door as per approved make & brand. (a) Natural Colour page 244/13/B/a

Supplying 4 lever mortice lock or any approved make and brand as per direction of the Engineer- in -Charge. i) 150 mm PCS item 12/i page 243

(A) Supplying Aluminium casted body hydraulic door closer as per I.S.I. PCS Item 13A , Page - 244

(E) Supplying 250mm long Heavy Type Aluminium window Peg Stay (Natural White) PCS [Item 13/E ] page-244

Applying Acrylic Emulsion Paint of approved make & brand on walls & ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) i) Standard Quality PCS [Item 4/i page- 201

(b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. PCS [Item 1/b page- 200

Supplying Santars PCS [Item 13 page- 303

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] (ii) With 1:4 cement mortar (a) 20 mm thick plaster PCS [Item 1] page- 189

Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600 mm X 600 mm X 10 mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tiles using cement @ 2.91Kg./sqM or using polymerised adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles / epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contrr]e) (I) With application slurry @1.75 kg/ Sq.m, 20 mm sand cement mortar (1:4) & 2 mm thick cement slurry at back side of tiles, 0.2 kg/ Sq.m white cement for joint filling with igment. (A) Deep Colour & White PCS [Item 36/A ] page- 66

Supplying fitting &fixing Vatical blind inculding rail. [Rate taking by C-79/A 2007-2008]

Partition of teak veneer [1 mm] as per design fitted and fixed complete (excluding the supporting frame work & necessary teak wood battens): In ground floor (i) 4mm thick commercial quality Page -180 Item-18

French polishing to wood work including preparing surface (ordinary gloss) (a) On new wood work Page -180 Item-18

Collapsible gate with 40mm x 40mm x 6mm Tee as top and bottom guide rail, 20mm x 10mm x 2mm vertical channels 100mm apart in fully stretched position 20mm x 5mm M.S. flats as collapsible bracings properly rivetted and washered including 38mm steel rollers including locking arrangements, fitted and fixed in position with lugs set in cement concrete and including cutting necessary holes, chasing etc. in walls, floors etc. and making good damages complete. Page -180 Item-18