Industrial Training Institute Tender

Pneumatic Trainer Kit -Each consisting of the following matching components and accessories: - 01 sets I. Single acting cylinder Max. Stroke length 50 mm, Bore dia 20 -1 No II. Double acting cylinder Max. Stroke length 100 mm, Bore dia 20 mm, magnetic type - 1 No III. 3/2-way valve manually-actuated, Normally Closed - 2 Nos IV. 3/2-way valve pneumatically-actuated, spring return - 1 No V. One-way flow control valve -2 Nos VI. 5/2-way valve with manually-operated switch -1 No VII. 5/2-way valve pneumatically-actuated, spring return -1 No VIII. 5/2-way pneumatic actuated valve double pilot -1 Nos IX. 3/2-way roller lever valve direct actuation Normally Closed -2 Nos X. Shuttle valve (OR) -1 No XI. Two-pressure valve (AND) -1 No XII. Pressure gauge 0-16 bar -1 Nos XIII. Manifold with self-closing NRV, 6-way -1 Nos XIV. Pushbutton station for electrical signal input with 3 illuminated smomentary-contact switches (1 NO + 1 NC) and 1illuminated maintained-contact switch (1 NO + 1 NC), Contact load 2A -1 No XV. Relay station with 3 ralays each with 4 contact sets (3NO+1NC or Change-over type), 5 A -1 Nos XVI. 3/2-way single solenoid valve with LED -1 Nos XVII. 5/2-way single solenoid valve with manual override and LED -1 Nos XVIII. 5/2-way double solenoid valve with manual override and LED -1 Nos XIX. Power supply unit, Input voltage 85 – 265 V AC, Output voltage: 24 V DC, Output current max. 4.5 A, short-circuit-proof. -1 Nos XX. Profile plate, Anodised Aluminium 1100x700 mm, with carriers, mounting frames and mounting accessories XXI) Cut section model for pneumatic components (To be fitted onto the pneumatic workstation) (charge of Annual Maintenance Contract (AMC) with required parts for five (05) years after expiry of Guaranty period)

Pneumatic Workstation :- with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide:(1) Work Table – Size(Approx.) L1200mmXW900mmXH900mm, with four castor wheels including two lockable wheels at the front side, (2) Drawer – Size (Approx.) – L460mmxW495mm xH158mm each, and overall size of Drawer unit (Approx.) - L470mmxW495mmxH825mm and (3) Drawer slide height (Approx.) 85mm. Mars. (charge of Annual Maintenance Contract (AMC) with required parts for five (05) years after expiry of Guaranty period)

Hydraulic Trainer Kit-Each consisting of the following matching components and accessories: I. Hydraulic Power pack with (1) external gear pump having a delivery rate of 2.5 lpm, (approx.) @1400 rpm operating pressure 60 bar, coupled to a single-phase AC motor(230 V AC) having start capacitor and ON/OFF switch and overload protection, (2) pressure relief valve adjustable from 0 – 60 bar, (3) oil reservoir, ≥5 litres capacity having sight glass, drain screw, air filter, and P and T ports. -1 No. II. Pressure relief valve pilot-operated -1 No III. Drip tray, steel size 1160 mm x 760 mm. -1 No IV. Pressure Gauge Glycerin-damped, Indication range of: 0 – 100 bar -1 No V. Four-Way distributor with five ports, equipped with a pressure gauge -1 No VI. Double acting hydraulic cylinder with a control cam, Piston diameter16 mm, Piston rod diameter10 mm, Stroke length 200 mm. -1 No VII. Suitable Weight for vertical loading of hydraulic cylinder - 1 No VIII. Mounting kit for weight for realizing pulling and pushing load -1 No IX. 3/2-way directional control valve with hand lever actuation. -1 No X. 4/2-way directional control valve with hand lever actuation. -1 No XI. 4/3-way directional control valve closed-centre position, with hand lever actuation -1 No XII. Non-return valve -1 No XIII. Pilot-operated check valve pilot to open. -1 No XIV. One-way flow control valve with integrated check valve -1 No XV. T-Connector with self sealing coupling nipples (2 Nos.) and quick coupling socket (2 No.). XVI. Profile plate, Anodized Aluminium, 1100x700 mm, with carriers, mounting frames and mounting accessories (To be fitted onto the Hydraulic workstation XVII) Hydraulic Workstation with 40 square mm aluminium profile legs, wooden work surface, and one pedestal drawer unit having 5 drawers, each with handles and individual locks, on metallic full panel drawer slide: (1) Worktable – Size (Approx.) L1200mmXW900mmXH900 mm, with four castor wheels including two lockable wheels at the front side, (2) Drawer – Size (Approx.) – L460mmxW495mm xH158mm each, and overall size of Drawer unit (Approx.) L470mmxW495mmxH825m m and (3) Drawer slide height (Approx.) 85mm. ) XVII) Cut-section models for hydraulic components (charge of Annual Maintenance Contract (AMC) with required parts for five (05) years after expiry of Guaranty period)