Indian Institute Of Science Education And Research Tender

Laying of one number XLPE insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of 3.5Cx 240 sqmm size in the existing cable tray OR existing masonary duct OR wall surface with suitable arrangemen of clamp/saddle as required.

Horizontal Installation of pipe 100 mm GI pipe as per BS1387 below the road at a depth of minimum 600 mm as per soil condition for crossing the cable and back filling of excavated area with cement concreteof Grade 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) complete with leveling, finishing etc. as per the direction of the Engineer-in-charge. Cement: Ultratek, Birla, ACC, Ambuja or equivalent GI Pipe Make :-Shyam steel/SRMB/Jai Balaji/Electrosteel or equivalent Bidders may note that if any other services like pipe line of Chiller,water pipe,HT/LT cable get dammage due to this moling work,same will be repaired/changed by the bidder. Quotated rates must be inclusive of cutting of horizotal trench in the both side of road for smooth crossing of pipe below the road and refilling of that cutting /damaged( inclusive cutting at the both adjacent side of road) area of the road with proper dressing will be totally under Bidder's scope without any additional price involvement.

Supply of following size 1.1 KV grade XLPE insulated insulated and PVC sheathed Armoured Aluminium power cable(A2XFY) of following technical Data sheet : 1.1 kV (A.C) & 1.5 kV (D.C ) to Earth AL conductor, XLPE insulated, galvanised steel strip / wire armoured Cables as per IS 7098 Part -1. Conductor : AL stranded compact shaped conductor as per Cl. 2, IS 8130. Insulation : Crosslinked polyethylene (XLPE) Phase Core Color : Red, yellow, blue Neutral Core Color : Black Inner Sheath : PVC / PVC tape as per IS 7098 (P - 1) Armouring : Single armouring of galvanised steel strip / wire Outer Sheath : PVC Type ST - 2 as per IS 5831. ( FRLS Type) Cable Color : Black Bidder should note that sample of the cable should be approved prior to the delivery at site form the same drum and athe cables will be supplied along with Factory Routuinee & type test cerificates for that perticular drum Make: Finolex, Polycab, Havells,KEI

3 X 16 sq. mm

3.5 X 240 sq mm

Supplying and making end termination with brass double compression gland for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. Make: Comet, Dowells,Connectwell

3 X 16 sq. mm (25mm)

3½C X 240 sq. mm

Supplying and making aluminum Lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. Make: Comet, Dowells,Connectwell

Aluminium lugs for 240 sq. mm cable (Crimp/ring Type Long Barrel)

Aluminium lugs for 16 sq. mm cable (Crimp/ring Type Long Barrel)

Supplying & commissioning of Jointing Termination kit of following size of LT Cable with outdoor type Heat-shrinkable LT Cable straight through joint betwen same size of LT cable, termination kit with necessary hardware fittings complete as required. Make: Raychem, 3M, Multipressing

Straight through jointing kit for 3.5CX240 sq. mm Armoured Aluminium LT power cable

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required. Make-Reputed

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc.with charcoal/ coke and salt as required. Make-Reputed

Supply, installation testing and commissioning of Outdoor Double Door Kiosk type weather proof distribution feeder pillar box of sutable size with a tapered at top (for protection from rain water) and made out of not less than 2.0 mm thick for load bearing members & 1.6 mm thick for doors, compartmentalized,IP 65, epoxy powder coated treated in 7 tank process finish with following items, front and back both side openable, duly hinged doors with locking arrangement by providing both sides hold drafts and all hardware for fabrication of box. The cubical panel should be mounted with hardware on angle iron frame long legs duly primered and black painted. Frame be grouted with cement concrete 1:3:6 ratio and providing brick masonry along angle iron frame above ground level complete with connecting strips, Bakelite sheet, earth stud etc. cable entry from bottom suitable for 3.5Cx 240/120/70 Sq.mm I/c & O/g respectively. The panel should comprise of as per following (Panel shall be fabricated in CPRI approved panel builder with approval of the Deptt.. Drawing of the feeder pillar shall be submitted for approval prior to fabrication) Make: As per approval of Engineer-in-charge of IISER-K INCOMER 400 A ,4P,36 KA Change Over(C/O) Switch (Make:- Havells,L&T,C&S) - 1No. 400 A, 4P, 36 KA TM Release MCCB with rotary handle - 1 No. (Make: Havells, ABB, Siemens, L&T) 400 A, TPN Aluminum bus bar. OUTGOING (Make: Havells, ABB, Siemens, L&T) 250 A 4P 36 KA TM ReleaseMCCB rotary handle- 3 Nos. 100 A 4P 36 KA TM Release MCCB rotary handle- 1 Nos Digitol multifunction meter- I set LED- RYB indicator lamps- 1 set CT-400/5A, Class-1, 15 VA - 3nos Control circuit with 6 A MCB

SITC of vintage look decorative pole with double arm swan bracket of 5 (five) Meter height ( measured without the height of Arm bracket) made of grooved mild steel pipe (inner core) having bottom dia min 114 x 5 mm thick and top section 88 mm Dia x 4mm thick. Outer section covered with vintage designed cast iron square/polygonal cast iron embellishments (min 160 mm cross section x 1000 mm Height) on the bottom section and designer embellishments in middle/top sections and also in joint areas as per the design approved by the Institute. The artistically curved bracket arm made of MS pipe spruced up with MS Scroll with gravity die cast aluminium floral and decorative CI embellishment is firmly held to the stem by way of cast iron clamps and the arm bears cast iron knobs at one end and other end to facilitate the luminaries from the vertical axis of the bracket stem crowned at top with a gravity die cast aluminium tomb of proportionate height. Mild steel mounting plate minimum 300 mm Square x 20 mm thick Steel of grade E250 to IS 2062 : 2011 with 4 elongated holes suit M20 x 600mm anchor (J)bolts of grade 4.6 at CC180. The base plate should have a cable entry hole at the centre. The pole is coated with pure polyester powder coating or epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint (coating thickness 60-80 microns). The Pole shall be provided with Graphite grey / Antique Copper as standard colour options. (Minimum Weight 170 Kg±10% Note: Cost of pole foundation is not included in this item but supply of foundation bolts/nuts as mentioned in covered under this item. Make- Bajaj/K-Lite/Orient

SITC of classic look LED post top /pendent type luminaire (as approved by department) of rating 100W (nominal), Color temperature 3000K(WW)/5700K(CW) (as per instruction of EIC), Color rendering index(CRI) =70. Fixture should be designed with a classic look and heritage touch. Housing should be elegantly designed pressure die casted heat sink for efficient thermal management and sturdiness with IP-66 protection rating. Luminaire should be with PC lens to ensure better uniformity of light distribution. High efficiency long life LED module with wide angle to ensure better uniformity. Nominal Luminous Efficacy 120 Lumen/watt,Fixture should be THD=10%, Power Factor0.95, Fixture driver should be - Built-in potted electronic LED driver with APFC , over Voltage protection, Surge Voltage Protection upto 10kV With Built In SPD Circuit NOTE: Rate should inclusive onsite warranty for a period of 2 years from date of supply of LED Luminaries. Make:- Bajaj/Crompton/Havells/Philips/K-Lite/orient as approved by Engineer-in-charge

FOUNDATION OF POLE Foundation with RCC(Gr.M20,PCC(1:3:6),12mm dia rod of size 600 mmx 600 mm x 1200 mm depth in ground with help of 4 Nos Foundation Bolt 20 mm Dia 750 Long hot dipped "L" Shaped duly finished with cement plaster, type bolt as per approved drawing. with Pole earthing by 25X6 mm 600 mm long GI Strip gruoting. Height of the foundation is to be min 450 mm above ground level Ordinary Portland Cement Grade 43: Ultratek, Birla, ACC, Ambuja TMT/Steel Sections: Shyam steel/SRMB/Jai Balaji/Electrosteel or equivalent