Hooghly River Bridge Commissioners Tender

Supplying and laying in the specified pattern of Interlocking Concrete Block Pavements (ICBP) with concrete blocks (with concrete grade as specified as per Table 1 of IS 15658:2006) manufactured in steel mould clamped to a vibrating table by hydrualic pressure (as per cl. no. 6.30 of IRC:SP:63(2018), from BIS licensee manufacturer, with spacer nib (Small protruding profiles on the vertical face of a paver block used as a device for keeping minimum joint gap in between the paving blocks, as per Cl. No. 3.26 of IS:15658) and of specified size and shape with aspect ratio (The ratio of length to thickness of a paver block, as per Cl.No.3.3 of IS:15658) as per Table 2 of IS:15658 with flexural strength/breaking load as per Annexure G of IS:15658, on the prepared base course of specified CBR as per Table 1 of IRC SP 63 (2018) or else as mentioned in design and drawing with a cushion of compacted bedding sand of 25-35mm thick (grading of the bedding sand as per clause 6.5.1 of IRC SP 63) and filling up the gaps in between paver blocks with joints filling sand (the grading of the joint filling sand will be as per clause 6.5.2 of IRC SP 63) and completing the edges with cut blocks as per Cl. No. 8.7 of IRC SP-63(2018) with proper confinement of bedding and joint filling sand, compaction, levelling and filling up of the edge gap. 80mm thick

Open Graded Premix Surfacing with Cationic Bitumen Emulsion using 13.2 mm (@ 0.018 m3/m2) and 11.2 mm (@ 0.009 m3/m2) size stone aggregates, premixed with Cationic Bituminous Emulsion (M.S. grade) conforming to IS : 8887-1970 @21.5 kg per 10 m² of surface, including cleaning, moistening the surface, applying tack coat with cationic bitumen emulsion, screening, cleaning and washing the stone chips, intimately mixing with emulsion using Concrete Mixer, laying the mixture uniformly over the surface and rolling with power roller after hand packing and pinning adequately to ensure a compact surface all complete as per specification and direction of the Engineer-in-charge including cost and carriage of stone materials and emulsion, including cost of labour, hire and running charges of road roller and other tools and plants and cost of all other incidental charges including hire charges and cost of fuel and lubricants of machineries and equipment for construction and quality control as per Technical Specification Clause 508.2 for Rural Roads of MORD.

Seal Coat B. Providing and laying Premixed Seal Coat (Type B) with approved quality sand/grit @ 0.6 m3/ 100 m2 and bitumen binder on thoroughly cleaned black top surface coated with tack coat, including heating and mixing cleaned sand/grit (100 % passing through 2.36 mm sieve and retained on 180 micron sieve) uniformly with bitumen binder, laying and spreading the mix at an uniform rate using suitable means, brushing the surface, if necessary, to ensure uniformity, followed by rolling with power roller including the cost and carriage of binder and aggregates, cost of heating the binder and aggregates and all other incidental charges, cost of fuel and lubricants, including hire charges of machineries, tools & plants required for construction and quality control complete as per Clause 511 of Specifications for Road & Bridge Works of MoRT&H (5th Revision). I. By Mechanical Means With Cationic Bitumen Emulsion (@ 10.50 kg / 10 sqm.)

Bituminous Macadam using Mobile Hot Mix Plant (Light Duty) Providing and laying bituminous macadam with Mobile Hot Mix Plant (Light Duty) using approved crushed aggregates of specified grading as per Table 500.7 premixed with bituminous binder, transported to site laid over a previously prepared surface at specified laying temperature by means of approved and suitable arrangements to the required grade, level and alignment and rolled with suitable power roller for break down, inter-mediate and finished rolling as per specification to achieve the desired compaction including cost and carriage of stone materials and bitumen, hire charges of machinery and equipment, cost of fuel and lubricants and wages of operational staff, quality control complete as per Specifications for Road & Bridge Works of MoRT&H (5th Revision). For Grading 2 (19 mm nominal size, 50-75 mm thick.)

Flagman: Positioning of a smart flagman with a yellow vest and a yellow cap and a red flag 600 x 600 mm securely fastened to a staff 1 m in length for guiding the traffic .

Portable Barricade in Construction Zone Installation of a steel portable barricade with horizontal rail 300mm wide, 2.5 m in length fitted on a 'A' frame made with 45 x 45 x 5 mm angle iron section, 1.5 m in height, horizontal rail painted (2 coats) with yellow and white stripes, 150 mm in width at an angle of 450, 'A' frame painted with 2 coats of yellow paint, complete as per IRC:SP:55-2001.