Higher Education Department Tender

Page-140, Item-4(b)c: Supplying fitting and fixing M.S. clamp for fixing door and window frame made of flat bent bar, end bifurcated, with necessary screws etc by cement concrete with stone chips (1:2:4) complete as per direction. (Cost of concrete will be paid seperately) b)40mm x 6mm, 200mmLength.

Page No. 141, Item No. 8: Iron Hasp Bolt of approved quality fitted & fixed complete.

Page No. 141, Item No. 10(b): Iron Hasp Bolt of approved quality fitted & fixed complete (oxidised) with 16 mm dia rod with centre bolt and round fittings. (b) 250mm long.

Page-200; Item-1(b) a &b Priming one coat on timber, plastered or on steel or other metalled surface with synthetic enamel or oil bound primer of approved quality including smoothening surface by sand papering etc.

b) On timbered or Plastered Surface Doors & Windows

Page-176; Item-8.A.a.iv & b.iv Two coats painting with best quality synthetic enamel paint of approved make and brand (With super gloss of approved quality any shade except white) including smoothening surface by sand papering etc. A) On timbered or Plastered Surface Doors & Windows with high glosy iii) Two Coats (with any shade except white

PWD Schedule Pg No.-64, 1- 35: Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (b) Area of each tile above 0.09 Sq.m (i) Coloured decorative

Page-66; Item-36, (i); A. Supplying and laying true to line and level vitrified tiles of approved brand (size not less than 600 mm X 600 mm X 10mm thick) in floor, skirting etc. set in 20 mm sand cement mortar (1:4) and 2 mm thick cement slurry back side of tiles using cement @ 2.91Kg./sqM or using polymerised adhesive (6 mm thick layer applied directly over finished artificial stone floor/Mosaic etc without any backing course) laid after application slurry using 1.75 Kg of cement per sqM below mortar only, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles / epoxy grout materials of approved make as directed and removal of wax coating of top surface of tiles with warm water and polishing the tiles using soft and dry cloth upto mirror finish complete including the cost of materials, labour and all other incidental charges complete true to the manufacturer's specification and direction of Engineer-in-Charge. (White cement, synthetic adhesive and grout material to be supplied by the contrr]e) | (1) With application slurry @1.75 kg/ Sq.m, 20 mm sand cement mortar (1:4) & 2 mm thick cement slurry at back side of tiles, 0.2 kg/ Sq.m white cement for joint filling with pigment. (A) Deep Colour & White P-64/I-35 suppling fixing set quality

Page: 35 of 3rd corrigenda-2018, Sl: 22.B (i) With Sand Cement Mortar (1:3) 15 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (b) Area of each tile above 0.09 Sq.m (i) Coloured decorative Total = 12.00 sq.m

Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75mm X 75 mm X 75 mm wooden blocks complete. 470 mm X 280 mm X 340 mm

Section- (A)-(V), Item-2 :Supplying, fitting and fixing vitreous china best quality approved make wash basin with C.I........................... damages and painting the brackets with two coats of approved paint. a) 550 mm. x 400 mm. size

Supplying, fitting and fixing Anglo-Indian W.C. in white glazed vitreous china ware of approved make complete in position with necessary bolts, nuts etc. (a) With 'P' trap (with vent)

Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc.

Supplying, fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete.ii) C. P. Flush Pipe

Section- (A)-(V), Item- 9.iv: Supplying, fitting and fixing approved brand P.V.C.CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia .ii) 450 mm long

Section- (A)-(V), Item- 10.iii: Supplying, fitting and fixing approved brand 32 mm dia P.V.C.waste pipe, with P.V.C. coupling at one end fitted with nessary clamps .C.P. over brass nut (For Sink only) (iii) 900 mm long

Supplying fitting & fixing UPVC pipe..schedule 80 (medeable duty)necessary for exported work,50mm

Supplying, fitting and fixing PVC pipes of approved make of (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes***including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (a) For Exposed work 25mm

Page -5, Item - 7: Supplying, fitting and fixing bib cock or stop cock. (f) (i) Polythene Bib Cock / Stop Cock (HD) with metal inlet (EMCO / ATLAS or equivalent)

P.V.C Partition:Supplying,fitting and fixing the partition, frame will be made with rectangularsteel tube of size 50mm x 25mm with wall thickness not less than 1.00mm. Thevertical members duly welded to the horizontal members shall be placed between 1000mm to 1200mm apart the entire partition frame will be securedly fixed to thewall, ceiling and floor using rawlplug or wooden gutties and screws etc.the frame will be painted with synthetic paint, the section of the partition frame will then fitted with PRINTED LAMINATED P.V.C extruded hollow section of size 100mmx25mm. panel with approved quality fixed in the place by means of P.V.C extruded beading on both sides or P.V.C extruded angles (20mmx18mm) on one side and P.V.C extruded beading (9mmx9mm) on other side,angle/beading will be fixed to the steel frame by 19mm (nos.6) self tapping steel screw placed at an interval of 450mm and complete in all respect as per direction of Engineer-inCharge with all labour and materials In ground floor..

Same item as 15mm in SL-21

Supplying fitting and fixing in position approved P.V.C. door frame (Matt finish) made of extruded P.V.C. multichamber hollow section having dimensions 60mm x 50mm x 2mm (+/-0.2mm), horizontal section will be joined with vertical section by

Supplying, Fitting & Fixing 30 mm thick both side prelaminated Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” ..........