Higher Education Department Tender

Laying only Cable above 50 sqmm but not exceeding 400sqmm through existing RCC/ Hume/GI Pipe/open masonary trench for single, 2, 3, 3½ and 4 core

Fixing of Cable along the lenth of O.H. pole incl. S & F MS pole clamps fabricated from 25 mm x 6 mm MS flat incl. painting

Supplying & fixing medium gauge GI Pipe (ISI-Medium) Protection with necessary fittings and jointing materials as Required a) 40 mm dia.

b) 50 mm dia.

c) 80 mm dia.

Supplying and fixing 240 V 32 A DP MCB (Legrand/L&T/Siemens make) of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection.

Supplying and fixing 415 V Four Pole MCCB of Breaking capacity 25kA/35kA with fixed thermal and fixed magnetic / adjustable thermal and fixed magnetic setting in existing DBs / enclosure and necessary connectiona (Legrand/L&T/Siemens make) a) 63 A

b) 160 A

c) 200 A

Supplying and fixing 415V, 250A TPN on load front operated Changeover switch (Seimens/ABB/HPL/L&T make) open execution type in SS enclosure/cubical with nuts bolts etc.

Straigh through Jointing of cable of different size by compound jointing kit including S&F ferrul, tapes and jointing materials (Brand approved by EIC) a) 3½ / 4 core 50 sqmm cable

b) 3½ / 4 core 25 sqmm - 35 sqmm cable

c) 3½ / 4 core 10-16 sqmm cable

Supplying and fixing 415V, TPN SFU open execution (ABB/L&T/Siemens make) in existing SS enclosure/cubical with nuts bolts etc. incl. S & F 3 nos. DIN type HRC fuse as per rating. a) 32 A

b) 63 A

Supplying and fixing compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables as below : a) 4 Core upto 16 Sq mm

b) 3.5 Core upto 50 sq mm

c) 3.5 Core upto 95 Sq mm

e) 3.5 Core upto 150 Sq mm

Finishing the end of following XLPE/PVC armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make), tapes, anticorrosive paste & jointing materials a) 4 Core x 16 Sq mm

b) 3.5 Core x 50 Sq mm

c) 3.5 Core x 95 Sq mm

e) 3.5 Core upto 150 Sq mm

Excavation of soil for installation of Earth Electrode and filling & ramming for soft soil

Ear thing with 50 mm dia. GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia. x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below: (a) By ISI-Medium GI pipe

Extra for treatment of soil by using salt & charcoal or coke for plate electrode

Connecting the equipment’s body to earth bus bar including S & F 25 mm x 6 mm galvanised (Hot Dip) MS flat on wall/floor with GI saddles as required and connection to equipment’s incl. drilling holes, with bolts, nuts, washers etc.

Fabrication, Supply & Installation of double door outdoor type both side openable feeder pillar box. construction having crown top made of CRCA sheet (Crown top and support frame by 3mm and rest of part by 2mm) with powder coated paint, base channel or angle leg should be provided at the bottom as per the weight of feeder pillar. Well ventilation, locking arrangement, dust proof, two point of body ear-thing including fuse unit with indicator lamp, danger board, and proper support for incomer and out-going cable shall also be provided. The feeder pillar should have comprising 600 ampere or 400 amperes (as per required and approve by the EIC) copper bus-bar with separate compartment (3phase neutral shall be high conductive electrolytic copper with PVC heat shrinkable sleeves with suitable colour coding. The material shall have copper containing of 99.9%). The feeder pillar should have provision for TPN SFU / MCCB as incomer and out-going with separate compartment including supply the proper size of copper bar or copper flexible wire to interconnection with in-comer and out-going SFU / MCCB including internal wiring complete set in all respect. The feeder pillar to be install in the brick foundation including necessary plaster, neat cement and punning as per satisfaction and direction of Engineer-in-charge. a) Box size (1.2M x 0.6M x 1.4M), front size 18.08 sq. ft. with provision for 1 (one) no. (100A-160A as required) TPN MCCB as incomer and 9 (nine) Nos. (32A - 63A as required) TPN SFU/MCCB as out-going. The size of the brick foundation (4.5’ x 2.5’ x 4’)

b) Box size (1M x 0.6M x 1.2M) front size 12.91 sq. ft. provision for 1(one) No. (63A-100A as required) TPN MCCB as incomer and 3 Nos. (32A-63A as required) TPN SFU/ MCCB including 8nos. D.P MCB as out-going. The size of the brick foundation (4’ x 2.5’ x 4’)

Fabrication, supply & Installation of double door outdoor type both side openable joint box (Size of the box 500mm X 450mm X 600mm) construction having crown top made of CRCA sheet (Crown top and gland plate 3mm and body by 2mm) with powder coated paint. Angle frame and leg shall be provided. The joint box comprising of 250A TPN Aluminium bus-bar with well locking arrangement, dust proof, two point of body ear-thing and proper support for incomer and out-going cable shall also be provided. The complete joint box to be install on brick foundation (size of the foundation 2.5’ x 5.5’ x 4’ also the foundation may be varying as per the site position) including necessary plaster & neat cement punning as per the satisfaction and direction of Engineer-in-charge. front size 2.42 sq. ft.

Supply of 1.1 Kv grade XLPE/PVC armored cables ( brand approved by the EIC) a) 4 core x 16 sq mm

b) 3.5 Core x 50 Sq mm

c) 3.5 Core x 95 sq mm

d) 3.5 Core x 150 sq mm

Add GST @ 18.00 %

Add L W Cess@ 1.00%