Health And Family Welfare Department Tender

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. In Gr.Fl

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. Gr.Fl i) Tor steel/Mild Steel,( Sail/Tata)

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and (upto roof of ground floor)

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfer ing corners as directed , Gr.Fl (i) With 1:6 cement mortar (c) 15 mm thick plaster, In side

Labour for taking out door and window frame including shutter for repair or replacement of different parts of the frame & refixing the same including mending good all damaes complete. (Concrete and brick work for mending damage will be paid separately)

Supplying and fixing Frames for Lead Lined FD120 Fire Rated Door System as per the IS: 3614-1992 Part-II and BS:476-1987 Part - 20 & 22 with 1st Class Malayasian Hardwood densified and pressure treated with fire retardent chemicals in vacuam inpregnation vessels under 160 PSI pressure as pe IS:401 and kiln seasoned to moisture below 15% as per IS:1141 of section 120mm x 70 mm and shielding the frame with 3 mm thick & 45 mm wide 2 (two) protective lead covering conforming to ASTM B749-03 for reducing the radiation level to 2 mrem in 1 hour as stipulated by code of Federal Regulation (CFR), placed parallel each other staggeredly with an lateral over lap of 20mm at the region of discontinuity and fixed inside along the the frame, spray coated with 2 coats of enamel paint after 1 coat of white wood primer of minimum 200 micron,with single row of Brush- Type intumescent strip (equivalent to ASTROFLAME ) of size 10 mm x 4 mm affixed in the slit of the Frame for fire and smoke sealing, etc. including all incidental charges complete in all respect as per direction of Engineer-in-Charge. [Note : Specific permission of the Superintending Engineer is required for execution of this item. ]

Supplying & fitting of 55mm thick asbestos free - fire, heat and smoke resistant composite Fire check Door Shutter complying with fire performance-FD120 as per IS:3614 (part -II)-comprising of 2x8 mm Calcium Silicate boards over Chemically treated (with Fire retardant chemicals in pressure impregnation vessels under 160 psi pressure as per IS:401 and kiln seasoned to moisture below 15% as per IS:1141) internal timber (Malaysian Hard Wood, densified to 810 kg/cum) frame work of 100 mm x 32 mm with 32mm thick infill of ceramic fiber (density 128Kg/cum), vermaculite mix faced with 3 mm Fire retardant High Density fire board on outerside & similar one over 3 mm thick protective lead covering conforming to ASTM B749-03 for reducing the radiation level to 2 mrem in 1 hour as stipulated by code of Federal Regulation (CFR), internally lipped with hardwood beading, and pasted in Hydraulic Press under 25 MPa, spray coated with 2 coats of in-tumescent paint of minimum 300 micron, and with single row of Brush- Type intumescent strip of size 10 mm x 4 mm affixed on peripheral slit on all edges of shutter except bottom for fire and smoke sealing, without any external lipping including fitting, fixing shutters in position but excluding the cost of hinges & other fittings as per direction of Engineer-in- Charge complete in all respect in Ground Floor. [Note : Specific permission of the Superintending Engineer is required for execution of this item. ]

GST 18%

cess 1%