Haldia Development Authority Tender

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (The quantum should be correted upto three decimals). (f) Sishu, Gamar, Champ, Badam, Bhola, Mogra, Hallak. Ref: Page No-114, Item No-(1),(f)

Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings. In ground floor. b) Sishu, Gamar, Champ,Badam,Bhola, Mogra, Hallak. Ref:Page No-117, Item No-(1),(ii)(b)

Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. (iii) 75mm. X 40mm. X 1.12mm. Ref:Page No - 140, Item no-(5)(iii)

(b)Priming one coat on timber or plastered surface with synthetic oil bound primer of aooroved quality including smoothening surfaces by sand papering etc. Ref: Page No-200,Item No-(1)(b) Door Windows

A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : a) On timber or plastered surface : iv) Two coats (with any shade except white) Ref: Page No-200,Item No-(2)(iv)

(b) Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. Ref: Page No-200,Item No-(1)(a)

(A) Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface With other than hi-gloss of approved quality- (iv) Two coats (with any shade except whiten Ref: Page No-200,Item No-(2)((b)(iv)

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured(matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's pecification and as per direction of the EIC.: (a) One Coat Ref: Page No-196, Item No-(8)(a) In Ground Floor: Less(Windows)

First Floor Less(Windows)

Second Floor Less(Windows)

Third Floor Parapat wall Water Tank Less (Door & Windows)

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground floor (Two Coat) c) Super Protective 100% Acrylic Emulsion Ref: Page No-197,Item No-(17)(c) In Ground Floor:

First Floor

Second Floor

Third Floor

Scraping of moss, blisters etc.thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc.(Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge) Ref: Page No-198, Item No-1 Top roof

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes. Ref:-Derived rate

(a)Applying 2 coats of bonding agent with synthetic multi functional rubber mulsion having adhesive and water proofing properties by mixing with water in proportion (1 bonding agent : 4 water : 6 cement) as per Manufacturer's specification. Ref: Page No-45,Item No-8(a)

Supplying & laying 3mm thick pre-fabricated plastomeric water proofing membrane conforming to EN 12311-1 & ASTMD 5147, manufactured with atactic poly propylene (APP) modified premium grade asphalt , specially reinforced with non-woven polyester core with polyester reinforcement @160 gms per sqm & both faces covered with thermo-fusible polyethylene film /MineraL on top face over a coat of primer @ 0.40 lit/sqm of manufacturer's specification on smooth,clean dry surface prepared wherever required.Lap joint shall be provided of 75 mm in longitudinal & 100 mm in transverse direction and fused using LPG/ Propane torch employing extra care ensuring full bondage, complete removal of entrapped air and sealing edges into grooves in appropriate manner as per direction of Engineer -in-charge all complete including materials,labour and applicable taxes. (Payment shall be made on the basis of finished surface area.). Membrane Property: Softening Point 150 deg C, Cold Flexibility -6 deg C, Tensile Strength, N/cm : 600 (longitudinal), 450 (transverse), Tearing Strength, N: 300 (longitudinal), 200 (transverse) Ref: Page No-92,Item No-4

Welding in M.S. structural work with gas or electric: (a) Tack weld Ref:Page No-84,Item No-16

Extra rate for using water proofing compound (or at manufacturer's specified rate) for concrete and plaster of various grades. Ref:Page No-39,Item No-60

Easing door and windows. Ref: Page No-108, Item No-75

Brick work with 1st class bricks in cement mortar (1:4) (b) In superstructure, ground floor Ref: Page No-15, Item No-7(b)

Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m. Ref: Page No-192, Item No-15

Uprooting and removing plants from the surface of walls parapet etc and making good damages. (Repairing of damages to be paid separately). (a) Small plant of girth of exposed stem upto 75 mm. Lift upto 6 mtr. Ref: Page No-278, Item No-10(a)

Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only). (viii) 40 mm dia Ref: Page No-(S&P)5, Item No-5(iv)

Cleaning silt of inspection pit. Ref: Page No-(S&P)96, Item No-2

Cleaning the exposed reinforcement preferably upto full diameter by wire brush, applying two coats of polymer based rust removing compound left for 24 hours, removing the coating and then applying two (2) coats of polymer modified anti corrosive protective coating formulated to inhibit the corrosion of reinforcement as per manufacturer's specification] [Mode of measurement:The affected surface area of reinforcement shall be considered for payment] Ref: Page No-45, Item No-6

Applying epoxy based reactive joining agent for joining the old concrete with fresh concrete to be applied within manufacturer's specified time as per manufacturers specification. (0.4 Kg / m² of concrete surface). Ref: Page No-45, Item No-7

Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew,reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for esories, specials. Payment for painting will be made seperately) (a) For Exposed Work PVC Pipes : Ref: Page no - 12,Item No-(19)(I)(a) 100mmm dia

Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992 Ref: Page No-[(S&P) P-68,Item No-23] 110 mm dia ix) Bend 45º

x) Bend 87.5º

xii) Door Bend (LH) & (RH)

xiv) Cross Tee with Door

Removing sludge from septic tank, soak well etc. by methor labour including disposal of the same outside the compound as directed. (b) Upto 30 users:- i) Within a lead of 150 metre Ref: Page No-[(S&P) -96,Item No-3(b)(i)

18% GST

1% CESS