Haldia Development Authority Tender

Hire and labour charges for shoring work (including necessary close plank walling, framing, Eucalyptus/Jhou bulla piling, strutting etc) complete as per direction of the Engineer-incharge for foundation excavation (vertical surface are in contact with supported earth is to be measured.) (This item should be executed on specific direction of the Enginner in charge). Depth upto 1.5 m. Ref:- PWD(B)-2017,Item No-6(a), Page No-3.

(a)For additional depth beyond 1.5 m. and upto 3.00 m. Ref:- PWD(B)-2017,Item No-6(b), Page No-3.

Supplying and laying Polythene Sheet (150 gm / sqm) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. Ref:- PWD(B)-2017,Item No-3, Page No-47.

Cement concrete with graded stone ballast (40 mm size excluding shuttering). In ground floor. (A) [Pakur Variety]. 1:3:6 proportion. Ref:- PWD(B)-2017,Item No-22(I)(A)(a), Page No-34.

Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor). (c) Steel shuttering or 9 to 12 mm thick approved quality ply board shuttering in any concrete work. Ref:- PWD(B)2017, Page No-42, Item No-36(C).

Controlled Cement concrete with well graded stone chips (20 mm graded nominal size) excluding shuttering and reinforcement with complete design of concrete as per IS : 456 and relevant special publications, submission of job mix formula after preliminary mix design after testing of concrete cubes as per direction of Engineer-in charge. Consumption of cement will not be less than 300 Kg of cement with Super plasticiser per cubic meter of controlled concrete but actual consumption will be determined on the basis of preliminary test and job mix foumula. In ground floor and foundation. [using concrete mixture] (a) M 25 Grade. Pakur Variety. In Foundation. Ref:- Rate Analysed.

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge annealed wire / welded for pile cage at every intersection, complete as per drawing and direction. Tor steel/Mild Steel SAIL/TATA/RINL. In Foundation. Ref:- Rate Analysed.

Brick work with 1st class bricks in cement mortar (1:6) (a) In foundation and plinth. Ref:- Rate Analysed.

Brick work with 1st class bricks in cement mortar (1:6) (a) In superstructure, ground floor. Ref:- Rate Analysed.

40 mm. thick damp proof course with cement concrete (1:1.5:3) (with graded stone chips 20 mm nominal size) with water proofing compound of approved brand @ 0.2% weight of cement including cost of materials over two coats of non toxic acrylic polymer modified cementitious waterproofing slurry coat complete [cost of water proofing compound and non toxic paint to be paid seperately) for underground water retaining structures. Ref:- PWD(B)2017, Page No-47, Item No-4

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary. (i) With 1:6 cement mortar. (c) 15 mm thick plaster. Ref:- Rate Analysed.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course,scaffolding/staging where necessary. (ii) With 1:4 cement mortar. (c) 10 mm thick plaster. Ref:- Rate Analysed.

Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary. (i) With 1:6 cement mortar. (b) 20 mm thick plaster. Ref:- Rate Analysed.

Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE:Cement 0.152 cu.m per100 sq.m. Ref:- Ref:- Rate Analysed.

Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (as necessary) and marble dust in proportion (1:2) including smooth finishing and rounding off corners including raking out joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75 kg/sq.m all complete including all materials and labour. In ground floor. 3 mm. thick topping (High polishing grinding on this item is not permitted with ordinary cement). Using grey cement. (iii) 35 mm. thick. Ref:- PWD(B)2017, Corrigenda 3, Page No-48, Item No-6(iii)

Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (a) One Coat. (ii) Solvent based interior grade Acrylic Primer. Ref:- PWD(B)2017, Page No-195, Item No-7(a)(ii).

Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty. (Two coats). (ii) Luxury Quality. Ref:- PWD(B)2017, Page No-201, Item No-4(ii).

Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (b) Two Coats. Ref:- PWD(B)2017, Page No-196, Item No-8(b).

Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.(Two Coat). (c) Super Protective 100% Acrylic Emulsion. Ref:- PWD(B)2017, Page No-197, Item No-17 (C).

Supplying, fitting & fixing UPVC pipes A Type and fittings conforming to IS:13592- 1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete. 110mm dia pipes. Ref:- PWD(B)-2017, Page No-213,Item No-21(A)(ii)

a)UPVC Fittings: Bend 87.5degree Ref:- PWD(B)-2017, Page No-213,Item No-21(B)

b)UPVC Fittings: Shoe. Ref:- PWD(B)-2017, Page No-213,Item no-21(B)

supply & delivery of submersible pumping machinery directly coupled with wet winding type submersible Motor having following specification. Discharge -10 m3 / hour, Head -45 mtr., Impeller-SS /GM/Noryl, Shaft-SS, Outlet- 50 mm dia, Motor single phase 220 Volt+5% wet winding type submersible motor, Mode of startng-DOI, Make-KSB / Pluga / Texmo / BG/ Kirlosker / Any approved make. N.B. - Majufacturer test certificate along with curve shart should be submitted at the time of delivery. Ref:- Rate cosidered in referencee to approved estimate for submersible pump of EE,Medinipur Mechanical Division PHE Dte. Vide Memo No 1351/4 dated 12.07.2012, Item No. 1.

Supplying, fitting and fixing PVC pipes for underground work of approved make of Schedule 80 (medium duty) conforming to ASTMD -1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted including cost of all materials ,jointing materials, cutting pipes, making threads ,cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories, specials.). PVC Pipes. (i) 50mm dia. Ref:- PWD SOR(S&P) 2017, Page No-13, Item No-19(II).

Supplying, fitting and fixing in position R.C.C. Manhole/ pit cover of approved make with rim of approved make (Heavy type) (ii) 560 mm dia. Ref:- PWD SOR(S&P) 2017, Page No-91, Item No-7(ii).

Applying 2 coats of Non-Toxic Acrylic Polymer modified Paint having adhesive & waterproofing properties by mixing in proportion (1 liquid: 4cementitious material) or as per manufacturer's specification for water proofing layer in water tank etc. Ref:- PWD(B)2017, Page No-45, Item No-8(b).

Supplying,fitting & fixing of 2-Track / 3-Track Aluminium sliding Window of all Aluminium sections viz. window frame (top,bottom & side frame), shutter (top, bottom, side & interlock member) made of aluminium alloy extrusions conforming to IS 733-1983 & IS 1285-1975, annodised conforming to IS 1868-1983, fitted with all other accessories viz. PVC roller, EPDM gasket, maruti lock, screws etc. including labour charges for fitting & fixing of aluminium 2-track/3-track sliding window with fixing of glass (excluding cost of glass) all complete as per architectural drawings and direction of Engineer-in-charge. 10-12 Micron thickness Annodizing film. Natural white. Ref:-PWD(B)2017, Page No-245, Item No-15.

Wood work in door and window frame fitted and fixed in position complete including a protective coat of painting at the contact surface of the frame exluding cost of concrete, Iron Butt Hinges and M.S clamps. (e) Sal : Malayasian. Ref:- PWD(B)2017, Page No-114, Item No-1(e).

Z-batten shutters of door and window as per design havings tongued and groovehalf lap jointed as per direction of the Engineer-in-Charge including fitting and fixing shutter in position, but excluding the cost of hinges and other fittings in ground floor. (A) Shutter with 25mm thick planks, 19mm thick battens. (ii) Sal : Malayasian. Ref:- PWD(B)2017, Page No-123, Item No-10(A)(ii).

Supplying, fitting and fixing M.S. clamps for door and window frame made of flat bent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as per direction. (b) 40mm X 6mm, 200mm Length. Ref:- PWD(B)2017, Page No-140, Item No-4(b).

Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. (vi) 100mm. X 50mm. X 1.25mm. Ref:- PWD(B)2017, Page No-140, Item No-5(vi).

Anodised aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws: (vi) 200mm long x 10mm dia. bolt. Ref:- PWD(B)2017, Page No-144, Item No-26(vi).

Anodised aluminium Aldrop / Sliding bolts of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 2681/66) fitted and fixed complete. (iv) 300mm x 19mm dia. bolt. Ref:- PWD(B)2017, Page No-145, Item No-28(iv).

Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: (a) With continuous plate base (Hexagonal/ Round rod). (vii) 150 mm grip x 12 mm dia rod. Ref:- PWD(B)2017, Page No-146, Item No-30(a)(vii).

(a) M.S.or W.I. Ornamental grill of approved design joints continuously welded with M.S, W.I. Flats and bars of windows, railing etc. fitted and fixed with necessary screws and lugs in ground floor. (i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr. Ref:- PWD(B)2017, Page No-104, Item No-13(i).

Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. Ref:- PWD(B)-2017, Page No-200, Item No-1(a).

Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. Ref:- PWD(B)-2017, Page No-200 Item No-1(b)

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary: a) On timber or plastered surface: (iv) Two coats (with any shade except white). Ref:- PWD(B)-2017, Page No-200, Item No-2(A)a(iv)

Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : b) On steel or other metal surface: (iv) Two coats (with any shade except white). Ref:- PWD(B)-2017, Pg-201 It-2(A)b(iv).

Commissing and Trial run of the whole fire portection and alarm system and obtaining NOC from Fire Department, Government of West Bengal. Ref:- Vetted by KMDA.

WET RISER SYSTEM, FIRE HYDRANT SYSTEM Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 300 lpm at 70 m Head. Ref:- CPWD, DSR & AOR Page No-02 ,Item No-3.2

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads. 1620 lpm at 70 m Head. Ref:- CPWD, DSR & AOR Page No-01 ,Item No-1.8

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable forautomatic operation and consisting of following,complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. 1620 lpm at 70 m Head. Ref:- CPWD, DSR & AOR Page No-02 ,Item No-2.8

VALVES & INSTRUMENTS Supplying, fixing, testing and commissioning of butterflyvalve of PN 1.6 rating with bronze /gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : Ref:- CPWD, DSR & AOR Page No-11 ,Item No-11.2 &11.6 a) 150mm dia

b)50 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : Ref:- CPWD, DSR & AOR Page No-12 ,Item No-14.2 &14.7 a)150 mm dia

b)50 mm dia

SITC of Foot Valve with flanges, nuts and bolts, gasket etc. Ref:-Rate Analysed. a)150 mm dia

b)80 mm dia

SITC of INDFOSS make pressure switches for cut-out and cut in pressure with cock & ball valve. Ref:-Rate Analysed.

SITC of 100 mm dia dial type pressure gauge complete with ball valve and cock. Ref:-Rate Analysed.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : a)150 mm dia Ref:- CPWD, DSR & AOR Page No-10 ,Item No-7.8

b)100mm dia Ref:- CPWD, DSR & AOR Page No-10 ,Item No: 7.7

c)80 mm dia Ref:- CPWD, DSR & AOR Page No-10 ,Item No-7.6

d)50 mm dia Ref:-CPWD, DSR & AOR Page No-10 ,Item No-7.4

e)25 mm dia Ref:-CPWD, DSR & AOR Page No-10 ,Item No-7.1

ACCESSORIES Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required. Ref:- CPWD, DSR & AOR Page No-12, Item No-13

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30 m Ref:- CPWD, DSR & AOR Page No-13 ,Item No-17

SITC of M.S. hose box with lockable arrangements to accommodate 1 RRL hose of 15 m length and one branch pipe. Ref:- Rate Analysed.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required: Gun Metal Ref:- CPWD, DSR & AOR Page No-13, Item No-16

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required: Gun metal Ref:- CPWD, DSR & AOR Page No-13, Item No-18.1

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required: 4 way - 150 mm dia M.S. Pipe. Ref:- CPWD, DSR & AOR Page No-13, Item No-19.2.

SITC of Air Release Valve-20mm size Ref:- Rate Analysed.

Supplying, fitting and fixing CPVC (Chlorinated Polyviny Chloride) pipes of approved make conforming to IS-15778: 2007 . with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials in any position above ground. (Payment will be made on the centre line measurements oftotal pipe line including all specials. No separate payment will be made for accesories, specials. Q) 25mm size ball valve (S.S.) Ref:- PWD,SOR S&P Page No-34 ,Item No: 1 (P)

SITC of 15mm gate valve (S.S.) Ref:- Rate Analysed.

AUTOMATIC SPRINKLER SYSTEM Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: a) 80 mm dia Ref:- CPWD, DSR & AOR Page No-10, Item No-7.6

b) 50 mm dia Ref:- CPWD, DSR & AOR Page No-10, Item No-7.4

c) 25 mm dia Ref:- CPWD, DSR & AOR Page No-10, Item No-7.1

Sprinkler operating at 68 degree centigrade standard response, standard coverage 15mm BPST, K56 UL listed and FM approved. 68 degree centigrade Pendant Sprinkler Ref:- CPWD, DSR & AOR Page No-85 ,Item Code No-4214

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/ sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasketetc of follwing sizes as required: 80 mm dia. Ref:-CPWD, DSR & AOR Page No-14 ,Item No-24.1.

ELECTRICAL WORKS : Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect,suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required : INCOMING 250A, 50kA 4 Pole MCCB, Ics=100% Icu rating Digital Voltmeter 0-500V with selector switch Digital Ammeter (0-250 A) with selector swtich & CTs etc. LED type RYB phase indicating lamps, ON, OFF, trip indicating lamps Set of Copper Bus Bar 300A OUTGOING ( Note : All outgoing feeders for pumps should have digital Ammeter with selector switches, and LED type ON, OFF, trip indicating lamps) Main Fire Pump 125 A, 50kA TPN MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable for 60 HP pump with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation. Jockey Pump 63 A, 50kA TPN MCCB, Ics=100% Icu, with suitable HP fully automatic Star/Delta starter with overload protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote, auto/manual/OFF operation. DIESEL ENGINE CONTROL Control for diesel engine comprising - Automatic/Manual selctor switch & 3 attempts starting device, timers and relays as required, push buttons, start/stop in manual mode Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on indication Battery charger suitbale for 12V/24 V DC with boost and trickle selector switch, 0-30 V DC volt meter, and 0- 20 A DC Ammeter. All standard relays and accessories for automatic operation of diesel engine System Controller Designing, Supply, Installation, Testing and commissioning of system controller to control operation of main electric fire pump, diesel pump, Pressurization pump, Terrace pump in sequence as per specification consisting of relays, timers. Sensors, annunciation window for fault indication, complete as per specification

Supply and delivery of 4 C X 70 Sq mm XLPE insulated and PVC sheathed aluminum armored Cable. As per IS 7098 Part -1 with latest amendment if any. The cable should have ISI mark.(Make-KEI,Havells,Gloster or equivalent)

Supply and delivery of 3 C X 50 Sq mm XLPE insulated and PVC sheathed aluminum armored Cable. As per IS 7098 Part -1 with latest amendment if any. The cable should have ISI mark.(Make-KEI,Havells,Gloster or equivalent)

Supply and delivery of 3 C X 10 Sq mm XLPE insulated and PVC sheathed aluminum armored Cable. As per IS 7098 Part -1 with latest amendment if any. The cable should have ISI mark.(Make-KEI,Havells,Gloster or equivalent)

Supply and delivery of 3 C X 1.5 Sq mm PVC insulated and FR PVC Round sheathed copper conductor (flexible) industrial Cable. The cable should have ISI mark.(Make-KEI,Havells,Gloster or equivalent)

Supply and delivery of 2 C X 1.5 Sq mm PVC insulated and FR PVC Round sheathed copper conductor (flexible) industrial Cable. The cable should have ISI mark.(Make-KEI,Havells,Gloster or equivalent)

Laying of one No. cable above 35 sqmm and upto 185 sqmm in underground trench 460mm wide x 760mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per Mtr. including filling the space between the bricks and cable and also the trenchwith shifted soil, leveling up and restoring surface duly rammed

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below:(a) By ISI-Medium GI pipe

Extra for providing masonery enclosure on the top of the earth electrode of overall size 86.36 cm x 86.36 cm x 46 cm deep (below Ground level) complete with cemented brick work (1:6) of 25 cm width duly plastered with cement morter (inside) CI hinged inspection cover of size 36.56 cm x 35.56 cm with locking arrangement, GI reducer including drilling of 46 nos. 12 mm dia holes on the GI pipe.

Excavation of soil for installation of Earth Electrode and filling & ramming.

Supplying & fixing earth busbar of galvanized (Hot Dip) MS flat 25 mm x 6 mm on wall having clearance of 6 mm from wall including providing drilled holes on the busbar complete with GI bolts, nuts, washers, spacing insulators etc. as required

Supply & fixing of GI (Hot Dip) strips 20 mm x 3 mm thick for vertical run on wall with GI saddles spaced not exceeding 1000 mm apart incl. mending good damages to building work

Connecting the equipments to earth busbar including S & F GI (Hot Dip) wire of size as below on wall/floor with staples buried inside wall/floor as required and making connection to equipments with bolts, nuts, washers, cable lugs etc. as required and mending good damages.6 SWG

Supplying & fixing medium gauge GI Pipe ( ISI-Medium) Protection with necessary fittings and jointing metarials as required.e) 50 mm dia

Supplying and fixing PVC Rigid Conduit 'FR' [Precision Make] on wall, ceiling with saddles and other accessories as required and mending good damages to building works a) 20mm size

FIRE ALARM SYSTEM Supplying, installation, testing & commissioningof Fire Alarm panel Single loop, intelligent analogue panel

Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.

Supplying, installation, testing & commissioning of heat detector operating at 54ºC/57ºC with rate of rise cum fixed temperature (dual thermistor) type with mounting base complete with all connection etc. as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as required.

Supplying, installation, testing & commissioning of Electronic Hooter-cum Sounder.

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required.

Supplying, installation, testing & commissioning of addressable beam detector with short circuit isolator (inbuilt or seperate) complete with emitter and receiver including connections with remote test features etc complete as required.

Supplying, installation, testing & commissioning of FDA panel for operation Beam Detector.

Supplying, installation, testing & commissioning of PA panel with one way addressable arrangement by microphone.

FIRE EXTINGUISHERS Supply Delivery and installation of ABC Powder type fire extinguishers (stored pressure) HSN code-84241000 conforming to IS:15683 and complete in all respect as per direction of EICD) 06 Kg with ISI marked Mono Ammonium Phosphate base Each 3721.00 ABC power conforming to IS:14609 and pressurized with nitrogen gas. Suitable for operating between (-)30ºC to (+)55ºC. Fire rating -2A & 21B

4.5 Kg capacity with ISI marked Co2 type fire extinguisher squeeze grip type conforming to IS:15683:2006 made from seamless cylinder conforming to IS:7285 duly approved by Chief controller of explosive, Nagpur, fitted with ISI marked controller of explosive, Nagpur, fittet withISI marked controlled valve conforming to IS:3224, high pressure 1 mtr. long discharge hose and horn completewith initial gas charged with carrying handle and wall mounting bracket suitable for operating between (-)30ºCto (+)55ºC. Fire rating -13B.

Supply, Delivery and installation of Co2 type fire extinguishers: HSN code-84241000 9 Kg capacity with ISI marked Co2 type fire extinguisher squeeze grip type conforming to IS:15683:2006 made from seamless cylinder conforming to IS:7285 duly approved by Chief controller of explosive, Nagpur, fitted with ISI marked controller of explosive, Nagpur, fittet with ISI marked controlled valve conforming to IS:3224, high pressure 1 mtr. long discharge hose and horn completewith initial gas charged mounted on trolley wheels.

1% CESS