Eastern Railway Tender

Fixing ,connection, testing and commissioning of 100 Amp 415 Volt, 50 Hz,minimum 36 KA 4 Pole microprocessor control LT MCCB with inbuilt overload , short circuit and ground fault protection with SS enclosure under voltage release (L &T Type- DN2-250D , Cat No. CM92152OOOOX1 4 or similar )with Digital type multifunction meter with RS 485 serial port & Calss -1 accuracy (L&T Cat no.- WL440011OOOO or similar) including connection through Cable entry box with gland socket and thimble for connection of cables, with proper fixing arrangement with clamps made of 50 mm x 6 mm MS flat and 14 SWG MS Sheet. MCCBs should conform to IEC:60947-2 /IS:13947-2 or latest) (make : Siemens , GE , Hager, L&T, ABB, schneider, legrand) (S=0.00, L=505.43)

Supply o f 63 Amp 415 Volt, 50 Hz,minimum 36 KA 4 Pole microprocessor control LT 5 MCCB with inbuilt overload , short circuit and ground fault protection with SS enclosure under voltage release (L &T Type- DN2-250D , Cat No. CM92153OOOOX1 or similar )with Digital type multifunction meter with RS 485 serial port & Calss -1 accuracy (L&T Cat no.- WL440011OOOO or similar) including connection through Cable entry box with gland socket and thimble for connection of cables, with proper fixing arrangement with clamps made of 50 mm x 6 mm MS flat and 14 SWG MS Sheet. MCCBs should conform to IEC:60947-2 /IS:13947-2 or latest )(make : Siemens , GE , Hager, L&T, ABB, schneider, legrand) (S=32775.00, L=0)

Fixing ,connection, testing and commissioning of 63 Amp 415 Volt, 50 Hz,minimum 36 KA 4 Pole microprocessor control LT MCCB with inbuilt overload , short circuit and ground fault protection with SS enclosure under voltage release (L &T Type- DN2-250D , Cat No. CM92153OOOOX1 6 or similar )with Digital type multifunction meter with RS 485 serial port & Calss -1 accuracy (L&T Cat no.- WL440011OOOO or similar) including connection through Cable entry box with gland socket and thimble for connection of cables, with proper fixing arrangement with clamps made of 50 mm x 6 mm MS flat and 14 SWG MS Sheet. MCCBs should conform to IEC:60947-2 /IS:13947-2 or latest) (make : Siemens , GE , Hager, L&T, ABB, schneider, legrand) (S=0, L=505.43)

Laying, jointing, connection, testing& commissioning of LT cable 1100V grade of higher 7 size (up to 95 sq.mm.) along the wall/catenary or garder truss by necessary clamping arrangement including socketing and termination with epoxy end jointing where necessary (clamp should be made of 50mm x 6mm M.S. Flat) (S=57.28, L=32.73)

Cutting of concrete and trenching drawing laying and jointing of the 1100V grade 8 cable through underground as per CEE's drawing no. E4/GPST/033/87 and refilling the trench after laying the cable including making good the damages and then smooth flooring and re-concreting (18" wide x min 3' deep) with cement , sand,& stone chips in ratio 1:2:4 and connection with switchergear along with supply of suitable size gland, socket etc as required. (S=334.26, L=286.35)

Supply , digging , insertion testing & commissioning of Earth pipe made of 2 numbers heavy guage G.I. pipe (Conforming to IS:1239 PART-1 (2004) or latest) of size 50 mm dia. 3 mtr long make TATA/JINDAL including cutting and boring of concrete floor at workshop/Colony area, construction of earth pit duly sorted by suitable length of G.I. Flat 50 mm x 6 mm including including necessary earth connection from pit to the distribution panel with 4 SWG GI wire..The earth should be 9 encashed with panel with alternate layer of salt & charcoal to be spreaded inside the pit. Eatrh pit shall be completted with necessary civil work like brick chamber, PCC Work and finally covered with medium duty cast iron hinged cover of size 400 * 400 mm2 .making good the damages with masonite flooring,heavy duty hinge C.I. pit cover along with charcoal and salt inside the earth pit including necessary earth connection from pit to the distribution panel with 4 SWG GI wire..N.B: The eatrthing should be done as per CEE/KKK's specifications . All earth value should be marked on MS Plate with date by painting work. The MS Flat , Plate should be painted by one coat of red oxide & Two coats of black Paint before execution. The marking should be done by white paint. (S=5358.00, L=5417.78)

Supply fixing , installation ,testing and commissioning of 8 Way, MCB DB 240 V , 50 HZ complete with enclosure with metal door 1 NO 40 Amp DP Isolator and 6 NOS. SP MCB 6-32 Amp (as 10 required) including connection and concealed with necessary arrangement ( MCB, DB, Isolator make: L&T, Siemens, ABB, C&S, Havells, Legrand,standard). ( MCBs should confirm to IS/IEC 60898-1 or latest & 60947-2 or latest )(Isolator should confirm to IS/IEC 60947-3 or latest) ( DB should confirm to IEC 61439-1&3 & IS 8623 -1&3 or latest with CRCE sheet steel.)(S=5174.00, L=300.00)

Supply fixing , installation ,testing and commissioning of TPN MCB DB 415 V , 50 HZ complete with enclosure & door with 12 NOS. SP 6-32 A MCB (as required)(4 nos. of MCB per phase as 11 outgoing) and one no. FP 100 amp Isolator as incoming including connection and fixing on wall with necessary clamping arrangement ( MCB, TPN DB, Isolator make: L&T, Siemens, ABB, C&S, Havells, Legrand,standard). (MCBs should confirm to IS/IEC 60898-1 or latest & 60947-2 or latest )(Isolator should confirm to IS/IEC 60947-3 or latest) (TPN DB should confirm to IEC 61439-1&3 & IS 8623 -1&3 or latest with CRCE sheet steel)(S=5995.21, L=307.96)

Supply, fixing, connection and testing of 400 mm sweep,1ph. bracket type wall mounted fan with suitable clamping arrangement (make - Crompton, Bajaj, GEC, Havells, Polar, Usha) (S=1927.76, L=80.46

Supply, Fixing & connection of 230 mm sweep metal exhaust fan with necessary masonry work ( Make Havells, Crompton, Bajaj, Usha,Polar,Orient).(S=1990.00, L=199.00)

Wiiring of submain with 2 nos. of single core HRFR/FRLSH PVC insulated stranded Copper conductor cable of size 6 sq. mm.,1100 V grade confirming to IS 694/2010 in suitable size heavy guage PVC pipe in concealed along with PVC insulated copper conductor cable of size 2.5 sq. mm for ECC.(Wire make : Finolex ,KDK, Havells, Polycab, Standard, RR Kabel)(S=143.20, L=33.10)

Wiring of light points, fan points,bracket fan points, exhaust fan point, sinage light, call bell point with 1.5 sq. mm. multi-strand single core HRFR/FRLSH PVC insulated copper conductor cable 15 1100 V grade confirming to IS 694/2010 in suitable size heavy guage PVC pipe in concealed along with PVC insulated copper conductor cable of size 1.5 sq. mm for ECC & suitable size heavy gauge PVC board, switches should be of modular type and all other accessories. (Wire make : Polycab,Havells , Finolex,KDK, KEI, RR Cable,mescab, gloster) , (5Amp switch make -Anchor, Crabtree, Legrand, L&T , HPL, standard )(S=619.77, L=63.90)

Wiring of Computer plug points with single core PVC insulated HRFR multi-strand copper conductor cable of size 4 sq. mm 1100 V grade conforming to IS:694-2010 through suitable 16 size PVC pipe (ISI marked) in concealed along with PVC insulated copper conductor cable of size 2.5 sq. mm for ECC and suitable size heavy gauge PVC board. Each board should consist of modular typr 3 nos. 5 amp socket and 3 nos.5 Amp switch with one 6 amp MCB . (Wire make : Polycab,Havells , Finolex,KDK, KEI, RR Cable,mescab, gloster) , (Switch , Plug socket make: Crabtree, Legrand, panasonic, L&T ) (MCB make Havells, legrand, simence, L&T,HPL)(S=1143.27, L=112.20)

Wiring of 6A/5 pin plug point with single core HRFR/FR-LSH PVC insulated multi-strand Copper conductor cable of size 1.5 sq. mm.,1100 V grade confirming to IS 694/2010 in suitable size 17 PVC pipe in concealed with PVC insulated copper conductor cable of size 1.5 sq. mm for ECC. & suitable size heavy gauge PVC board. switch & socket should be of Modular type .(Wire make : Polycab,Havells , Finolex,KDK, KEI, RR Cable,mescab, gloster) , (5 amp switch, socket make -Anchor, Crabtree, Legrand, L&T, HPL,standard )(S=326.44, L=42@46"41@

Wiring of 16/6 Amp 6 pin plug point with single core HRFR PVC insulated multistrand Copper conductor cable of size 4 sq. mm.,1100 V grade confirming to IS 694/2010 in suitable size PVC 18 pipe in concealed and made 16/6 Amp socket and switch along with PVC insulated copper conductor cable of size 2.5 sq. mm for ECC. & suitable size heavy gauge PVC board. Switch & socket should be of Modular type (Wire make : Polycab,Havells , Finolex,KDK, KEI, RR Cable,mescab, gloster) , (16 amp switch, socket make -Anchor, Crabtree, Legrand, L&T , HPL,standard ) (S=1044.75, L=63.90)

Supply & fabrication of Thermo -Mechanically Treated bars of grade Fe-500D or more as down rod for hanging of ceiling fan (Length of down rod and fabrication of the same as per site requriment)(S=89650.00, L=0)

Dismantalling of existing fan & refixing, connection ,testing of ceiling fan with necessary MS clamping arrangement.(S=74.01, L=24.15)

Supply ,Fixing connection , testing and commissioning of 7 Watt LED linear mirror light fitting with lamps with suitable size and shape MS clamp as required .( make, Orient,Crompton , Bajaj, Philips, Havells, Syska,Reshmi LED,Halonix)(S=1415.07, L=32.63)

Supply ,Fixing ,connection , testing and commissioning of Recess Downlighter 15 Watt 22 LED light fitting with Flicker controlled technology and with all accessories (Orient Electric Model no.- LDRER-15-C-V2-FC or equlivant) .( make, Orient,Crompton , Bajaj, Philips, Havells, Syska,Reshmi LED,Halonix)(S=827.18, L=99.50)

Supply ,Fixing ,connection , testing and commissioning of 2ft x 2ft Recess mounted 36 23 Watt LED light fitting with Flicker controlled technology and with all accessories (Orient Electric Model no.- LTRAQ-36-C-FC or equlivant) .( make, Orient,Crompton , Bajaj, Philips, Havells, Syska,Reshmi LED,Halonix)(S=1859.70, L=199.00)

Supply ,Fixing ,connection , testing and commissioning of Recess Square Downlighter 15 Watt LED light fitting with all accessories (Orient Electric Model no.- LDRNS-015-C-V1 or equlivant) . ( make, Orient,Crompton , Bajaj, Philips, Havells, Syska,Reshmi LED,Halonix)(S=973.50, L=99.50)

Supply ,Fixing ,connection , testing and commissioning of Linear Light Recess mounted 28 Watt LED light fitting with all accessories (Orient Electric Model no.- LCRDL4-28-C-50 or equlivant) . ( make, Orient,Crompton , Bajaj, Philips, Havells, Syska,Reshmi LED,Halonix)(S=3835.00, L=199.00)

CARRIAGE OF MATERIALS // By Mechanical Transport including loading,unloading 1 and stacking // Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in- charge. Per bag of 4.12 96.00 cement of 57.15 5486.40 (-) 7.00 5102.35 2

CONCRETE WORK // CEMENT CONCRETE (CAST IN SITU) // Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, 3 columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: // 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

MASONRY WORK // Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : // Cement mortar 1:6 (1 cement : 6 coarse sand)

WOOD AND P.V.C. WORK // FRAMES AND TRUSSES // Providing wood work in frames 5 of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). // Sal wood

WOOD AND P.V.C. WORK // Providing and fixing panelled or panelled and glazed 6 shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) // Kiln seasoned and chemically treated hollock wood // 35 mm thick shutters

WOOD AND P.V.C. WORK // Providing and fixing panelled or panelled and glazed 7 shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) // Float glass panes // 5.0 mm thick glass panes (weight not less than 12.50 kg/sqm).

WOOD AND P.V.C. WORK // STAINLESS STEEL FITTINGS // Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete : // 100X58X1.90 mm

WOOD AND P.V.C. WORK // GYPSUM BOARD PARTITIONS // Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing 9 of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. // 75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks)

WOOD AND P.V.C. WORK // GYPSUM BOARD PARTITIONS // Providing and fixing 10 18mm thick both sides Pre-laminated cement bonded wood particle board as per IS : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. in partitions, boxes, shelves, racks and cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of Engineer-in-charge (Note: Fittings to be paid separately). // 18 mm thick

WOOD AND P.V.C. WORK // GYPSUM BOARD PARTITIONS // Providing and fixing 11 6mm thick both sides Pre-laminated cement bonded wood particle board as per IS : 15786:2008 of approved brand and shade with suitable full threaded steel screws etc. on the backing of racks, drawer, cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of Engineer-in-charge.

STEEL WORK // Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

FLOORING // VITRIFIED FLOOR TILES // Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 13 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. // Glazed Vitrified tiles Matt/Antiskid finish of size // Size of Tile 600 x 600 mm

FLOORING // VITRIFIED FLOOR TILES // Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and 14 conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. // Size of Tile 600x600 mm

ROOFING // Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. // Providing 15 and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. // 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

ROOFING // Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. // Providing 16 and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

FINISHING // 6MM CEMENT PLASTER // 6 mm cement plaster of mix : // 1:3 (1 cement : 3 fine sand)

FINISHING // Extra for plastering: // Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

FINISHING // Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : // New work (two or more coats) over and including water thinnable priming coat with cement primer

FINISHING // Painting with oil type wood preservative of approved brand and manufacture : // New work (two or more coats)

REPAIRS TO BUILDING // Repairs to plaster of thickness 12 mm to 20 mm in patches 21 of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. // With cement mortar 1:4 (1cement: 4 coarse sand)

DISMANTLING AND DEMOLISHING // Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. // Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

DISMANTLING AND DEMOLISHING // Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. // In cement mortar

DISMANTLING AND DEMOLISHING // Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge.

DISMANTLING AND DEMOLISHING // Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. // For thickness of tiles 10 mm to 25 mm

DISMANTLING AND DEMOLISHING // Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

DISMANTLING AND DEMOLISHING // Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

SANITARY INSTALLATIONS // Providing and fixing white vitreous china battery 28 based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Outdoor & core industrial amoured OFC cable (Make-Digisol/D-link/Similar) 2

Single mode SC pigtel(Make-Digisol/D-link/Similar) 3

Simplex SM SC-SC OFC patch cord 3m (Make-Digisol/D-link/Similar) 4

Supply of UTP Cat6 cable 305m in a box (Make-Digisol/D-link/Similar) 5

25/20mm PVC pipe as per requirement (Make-ISI) 6

GST @ 18% on item no.1 to 5 of EDPM work 7

Indoor/Outdoor laying of UTP & OFC Cat6 Cable through PVC 8

OFC splicing charges 9

Overall installation, dismantle and repair charges. 10