Eastern Coalfields Limited Tender

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Demolishing brick work manually/ by mechanical means including stacking ofserviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge In cement mortar (.415 ROOM)

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and fxing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fxing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fxing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of pqwder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shuttersand partitions etc. with EPDM rubber / neoprene gasket etc. complete as perthe architectural drawings and the directions of engineer-in-charge . (Cost ofaluminium snap beading shall be paid in basic item): With float glass panes of4 mm thickness (weight not less than 10.kg/sqm)

Providing and fixing glazing in aluminium door, window, ventilator shuttersand partitions etc. with EPDM rubber / neoprene gasket etc. complete as perthe architectural drawings and the directions of engineer-in-charge . (Cost ofaluminium snap beading shall be paid in basic item): 5mmWith float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) geology deprt showcase

Providing and fixing glazing in aluminium door, window, ventilator shuttersand partitions etc. with EPDM rubber / neoprene gasket etc. complete as perthe architectural drawings and the directions of engineer-in-charge . (Cost ofaluminium snap beading shall be paid in basic item): With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)for base show case

Providing and fixing two track aluminium channel for sliding shutter showcase

Providing fixing sliding shutter lock for showcase

Providing and laying vitrified floor tiles in different sizes (thickness to bespecified by the manufacturer) with water absorption less than 0.08% andconforming to IS: 15622, of approved make, in all colours and shades, laid on20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with greycement slurry @ 3.3 kg/ sqm including grouting the joints with white cementand matching pigments etc., complete.eThe tiles must be cut with thezero chipping diamond cutter only . Laying of tiles will be done with the notchtrowel, plier, wedge, clips of required thickness, leveling system and rubbermallet for placing the tiles gently and easily.Double charge vitrified tile polished finish of size.Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness to be specifiedby anufacturer), with water absorption less than 0.08 % and conforming toI.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps,over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointingwith grey cement slurry @ 3.3 kg/ sqm including grouting the joint with whitecement & matching pigments etc. complete.Size of Tile 600x600 mm

Providing and fixing bright finished 100 mm mortice lock with 6 leverswithout pair of handles of approved quality for aluminium door, withnecessary screws etc complete as per direction of Engineer- in-charge

Providing and fixing 150 mm bright finished floor brass door stopper withrubber cushion, necessary brass screws etc. to suit shutter thickness complete

Removing dry or oil bound distemper, water proofing cement paint and thelike by scrapping, sand papering and preparing the surface smooth includingnecessary repairs to scratches etc. complete.

Providing and applying white cement based putty of average thickness 1 mm,of approved brand and manufacturer, over the plastered wall surface to preparethe surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand andmanufacture on wall surface : Water thinnable cement primer

Wall painting with acrylic emulsion paint of approved brand and manufactureto give an even shade :Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture togive an even shade :One or more coats on old work door

Providing and fixing plain lining with necessary screws/nuts & bolts/ nailsincluding a coat of approved primer on one face, and fixed on wooden /steelframe work, complete as per direction of Engineer-in- charge (Frame workshall be paid for separately)12 mm thick century or equivelent BWP ply

Providing & Fixing 1 mm thick premium quality decorative high pressure laminated sheet of TEXTURE-LN/AL/LO/PK/UL/UM ,including cost of adhesive of approved qualitycomplete as per direction of Engineer-in-charge.

Providing and fixing 19mm thick green or its equivelent BWP grade marine ply as per IS 710 of approved brand boxes ,shelves, racks almirah, cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of Engineer-in-charge.

Providing & Fixing 1 mm thick premium quality SOLID COLOUR / SUEDE FINISH / MATTE FINISH / COMBINATIONS / WOODGRAINSlaminated sheet of ,including cost of adhesive of approved qualitycomplete as per direction of Engineer-in-charge.

Providing and fixing chromium plated brass 50 mm cupboard or wardrobe knobs with nuts complete.

Providing and fixing chromium plated brass handles with necessary screwsetc. complete:125 mm

Providing and fixing ISI marked aluminium butt hinges anodised (anodiccoating not less than grade AC 10 as per IS: 1868) transparent or dyed torequired colour or shade with necessary screws etc. complete75x63x4 mm

Carriage of MaterialsBy Mechanical Transport including loading,unloading and stackingLime, moorum, building rubbish Lead - 5 km

Total impact of GST for the purpose of CTC