District Magistrate Tender

Single Brick Flat Soling of picked jhama bricks including ramming anddressing bed to proper level and filling joints with local sand.PWD 14 / 1 : Rate: as per 3rd Corrigendum : Rs 322.00 / sqm Floor

Supplying and laying Polythene Sheet (150gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches

Cement Concrete with graded stone ballast (20 mm size) excluding shuttering etc. as per direction of Engineer-in-charge, complete. In 6:3:1 proportion.In foundation.

Brick work with 1st class bricks in cement mortar (1:6) (a) In foundation and plinth

Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mmnominal size) excluding shuttering and reinforcement if any, in ground flooras per relevant IS codes.(i) Pakur Variety

Hire and labour charges for shuttering with centering and necessary stagingupto 4 m using approved stout props and thick hard wood planks of approvedthickness with required bracing for concrete slabs, beams and columns,lintels curved or straight including fitting, fixing and striking out aftercompletion of works (upto roof of ground floor)(a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of

Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods, initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every inter-section, complete as per drawing and direction.(ii)JSW/JSPL/SHYAM/ SRMB/BMASL/ELECROSTEEL/SSL.

125mm thick brick work with 1st class brick in cement mortar (1:4) in ground floor

Plaster (to wall, floor, ceiling etc.) with sand and cement mortarincluding rounding off or chamfering corners as directed andraking out joints including throating, nosing and drip course,scaffolding/staging where necessary (Ground floor).(Excludingcost of chipping over concrete surface) 15 mm thick plaster in sand cement morter (1:6) to in side and out side.

Neat cement punning about 1.5mm thick in wall, dado, windowsill, floor etc.NOTE:Cement 0.152 cu.m per100 sq.m.

M.S. Structural works in roof trusses with tubular sections conforming to IS.806- 1968 & IS 1161-1998 connected to one another with bracket.gusset cleats as pewr design.direction of Engineer -in -charge completed including cutting to requisile size.fabrication with necessary metal are welding conforming to IS 816-1669 and IS 9595 uning electrodes of approved make and brand conforming to IS 814-2004.haulage . hoisting and erection all complete The rate includes the cost of rolled steel section.conumables suchas electrodes.gas and hire charge of all tools and plants and labour reqired for the work including all incidental chages such aselectricity charges.labour insuranced charges etc payment to be made on the basis of calculated weight of structuraltubular memebrs as specified in relevent IS code in finsished work Payment for gussel bracket.cleat may be made by adding the actual weight of such item with weight of finshed structural member.the rate are consider for a height of irection 8m / 2nd floor level from the ground Add 1.5% extra over the rate for each additional floor or 4m beyond the initial 8m or part there of (i) For trusses spanning upto 12.00m

Galvanised corrugated iron sheet work ( including the supporting frame work) fitted and fixed with 10mm. Dia J or L hook bolts , limpet and bitumen washers and putty complete with 100mm end lap and one corrugation minimum side lap ( payment to be made on area of finised work)( (GCI sheet to be supplyed by contructor (1) In Roof- (b) With 0.60mm thick sheet

Gllalvanised iron sheet ridging fitted with necessary bolts.screws,washers,etc complete ( 225mm end lapping ) B) 450mm lapping each way (b) With 0.63mm sheet

Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles inclu-ding roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m. (a) Area of each tile upto 0.09 Sq.m (ii) Other than Coloured decorative

M.S. or W. I. ornamental grill of approved design joints continuously welded with M.S., W.I. flats and bars for windows, railing etc fitted & fixed with necessary screws and lugs in G.F. Grill weighing 10 to 16 kg./ Sqm.

Artificial stone in floor, dado, staircase etc with cement concrete (1:2:4) with stone chips, laid in panels as directed with topping made with ordinary or white cement (asnecessary) and marble dust in proportion (1:2) includingsmooth finishing and rounding off corners including rakingout joints or roughening of concrete surface and application of cement slurry before flooring works using cement @ 1.75kg/sqm all complete including all materials and labour In ground cfloor 3mm thick topping (High polishing grinding on this item is not permitted with ordinary cement) Using grey cement (ii)25mm thick

Painting with best quality synthetic enamel paint of approved make and brand including smoothenig surface by sand papering etc. including using of approved putty etc. on the surface if necessary. With other than hi-gloss of approved quality- (iv) Two coats (with any shade except white) A) On Steel or other Metal surface

Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer's specification. In Ground floor: (iii) Two coats

Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (a) For Exposed Work PVC Pipes i) 15 mm dia. medium quality

ii) 20 mm dia. medium quality

Supplying, fitting and fixing alloy iron with brass spindle bib cock / stop cock of approved brand and make , spray painted and tested to 21 Kg per sq, cm. (i) 15 mm dia [ P- 7, I-7(g) ]

Add cost for Displayboard and photography

GST @ 18.00 %

Cess @ 1.00 %