Department Of Rural Development And Panchayats Tender

Providing and fixing of false ceiling with powder coated exposed G.I. grid suspension system (E-Grid U-1520 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200mm c/c ) consisting of Main Runner 3600 mm long, Cross Tee 1200 mm / 600 mm long and Wall Angle. The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300mm c/c. The Main Runners to be placed @ 1200 mm. The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm X 600mm. Additional Cross Tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600 mm X 600 mm. Grid of module size 600 mm X 600 mm shall be supported by 6 mm dia G.I. wire from purlins / soffit. 15mm thick OW Acoustic Board (Mineral Fiber Acoustic Ceiling Tiles) of approved patern and size 595mm X 595mm with NRC value 0.65 should be placed in the Grid module to form a False Ceiling. All complete as per the drawing & directions of Engineer-in-charge. In First floor. a) Acoustic False Ceiling (with 15mm thick OW Acoustic Board and E-Grid U- 1520).

Supplying, fitting and fixing boiling water resistant ply conforming to IS: 303-1989 bonded with phenol formaldehyde synthetic resin of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in Charge.[excluding the cost of supporting frame work and teak wood batten/Lipping] In Ground Floor (ii) 6mm

Supplying fitting, fixing decorative lamination conforming to IS: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on Particle/MDF / Ply Boards with recommended / approved adhesive with proper clipping the sides for better attachment as per direction of Engineer-in charge.The rate includes the cost of labour, adhesive and all incidental charges thereof. In ground floor Glossy/Matt/Suede excluding surface texture or metallic lustre. (i) Thickness of laminate 1.5mm

Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor) (b) Two Coats ii) Solvent based interior grade Acrylic Primer

Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) ii) Luxury Quality

Tile Carpet Flooring : Providing and laying Tile Carpet, nylon of pile content 100%, 6-7mm total thickness and bitumin backing with anti-static, thermal resistance, sound insulation & sound absorbtion properties. Carpet to have fire resistance of Cfl-s1 (with adhesion) and suitable for allergies. Rate includes complete installation as per direction of the EIC.

Window Blinds : Providing and fixing of Roller Blinds with black-out fabric, all complete as approved by the Architect.

Supplying and placing in position Main table of the following specifications. The Main table shall be of size 1800 Width mm x 900 mm Depth x 750 mm height. Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and final coating of PU. The Main desk should contain in built key board pull out tray for keeping keyboard of computer. The front modesty panel of the table shall be made up of MDF board of size 1640 mm x 600 mm x 16mm which shall also be duly finished with Veener and PU coating. For personal storage one mobile pedestal (3 drawer unit) shall be provided of size 510 mm Width x 635 mm Height and 445 mm Depth. The storage pedestal shall also be made up of MDF duly finished with veener & final coating of PU. The Side shall be of size 1200mm Width x 445mm Depth x 660 mm Height. The side unit shall be made up of MDF board duly finshed with Veneer and final finish by PU Coating. The design of the side unit shall be such that it can be placed on either side of the main table. The side unit shall contain open space for keeping cpu in extreme right side, one closed storage shutter at extreme left end & open space in the middle with one shelf for keeping files. The thickness of the top of the side unit shall be 25mm. Quality Certification: The manufacturer should have ISO 9001:2015, ISO 50001:2018, ISO 45001:2018, ISO 14001:2015 (all ISO must be from IAF recognised accreditation body), BIFMA (membership), AIOTA, Greenguard (by UL), GRIHA, Indian Design Mark, BIFMA Level-2, Indoor air quality certification.

Providing, supplying and placing of High Back Chair. SEAT ASSEMBLY: The seat is made up of 1.5±0.1 cm thick hot-pressed plywood upholstered with fabric and moulded polyurethane foam. SEAT SIZE: 51.8cm (W) x 49.7cm (D). BACK ASSEMBLY: The Back is injection moulded in glass filled Polypropylene which is 2 upholstered with Mesh fabric. The back consist of adjustable Lumbar support made of injection moulded Polypropylene having an adjustment of 5.0 10.1 cm. BACK SIZE: 47.9 cm(W) x 66.9 cm (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45+/-2 kg/m and hardness 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS (ADJUSTABLE):The height adjustable armrest is made of Polypropylene and can be adjusted to 6.010.1cm height it also has swivel and To and Fro adjustment with moulded PU armtop. ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features: 360° revolving type, Front-pivot for tilt with feet resting on ground & continuous lumber support ensuring more comfort, Till tension adjustment can be operated in seating position, 5-position Tilt limiter giving option of variable sit angle to the chair. Seat/back tilting ratio of 1:2. The mechanism housing is made up of HPDC Aluminium & black powder coated (DFT 40 to 60 micron). HEADREST: The Headrest sub-assembly is made up of injection moulded glass filed Polypropylene which is upholstered with moulded HR polyurethane loam and fabric has an adjustment of 3.00.1cm & it is assembled over GRETA 20F The complete headrest assembly is retro fic to the main chair. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with an adjustment stroke of 10.0±0.3cm. PEDESTAL ASSEMBLY: The pedestal is injection moulded in black 30% glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 166.1±0.5 cm.(76.1 ± 1.0 cm. with castors). TWIN WHEEL CASTORS: The twin wheel castors are Injection moulded in black Polyamide having 6.01 0.1cm wheel Diameter. WIDTH (W) - 76.0cm. DEPTH (D) - 76.0cm, HEIGHT (H) - 114.0 cm- 123.5cm, SEAT HEIGHT - 43.5 - 54.0cm. Quality Certification: The manufacturer should have ISO 9001:2015, ISO 50001:2018, ISO 45001:2018, ISO 14001:2015 (all ISO must be from IAF recognised accreditation body), BIFMA (membership), AIOTA, Greenguard (by UL), GRIHA, Indian Design Mark, BIFMA Level-2, Indoor air quality certification.

Supplying and placing in position Back unit of the following specifications. The Size of the Back unit shall be 1000 mm width x 480 mm Depth x 2035 mm height. The back unit shall be made up of MDF board duly finished with veneer & final finish by PU coating. The mobile unit can be bought in multiples.PU coating hardness 1.5H. Quality Certification: The manufacturer should have ISO 9001:2015, ISO 50001:2018, ISO 45001:2018, ISO 14001:2015 (all ISO must be from IAF recognised accreditation body), BIFMA (membership), AIOTA, Greenguard (by UL), GRIHA, Indian Design Mark, BIFMA Level-2, Indoor air quality certification.

Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987. v) 6mm thick clear glass.

Supplying, fitting and fixing boiling water proof block board conforming to IS:1659-1990 conforming to IS:848-1974 of approved make and brand, fitted and fixed as per design as per direction of Engineer-in-charge. [Excluding the cost of supporting frame work and teak wood batten / Lipping]. (ii) 19mm (For preparation of Foot Rest)

GST @ 18%

LWC @1%