Department Of Rural Development And Panchayats Tender

Providing, supplying and placing of 3-Seater Public Seating Chair with Cushion. SEAT SHELL :The seat shell should be a welded assembly of seat,back and side frame. The seat and back should be made of 0.12±0.013cm thk CR steel sheet with oblong perforations.They should be welded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk HR steel.The welded assembly should be powder coated ( DFT 40-60 microns ). The seat has a front water fall edge to provide popliteal clearance for comfortable seating. It also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. Clean and flat surfaces of seat and back aids in easy maintenance. * SEAT SIZE : 47.8 cm (W) x 44.6 cm (D) * BACK SIZE : 41.6 cm (W) x 23.0 cm (H) Understructure assembly consshould be ts of connecting beam and leg assembly made of M.S. E.R.W. oblong tube of size 7.5±0.03cm x 2.5±0.03cm x 0.2±0.016cm thk.The welded structure assembly should be powder coated ( DFT 40-60 microns ).The leg assembly should be fitted with shoes and levellers in Nylon. The leg structure should be designed with minimal should be a of contact close to ground providing easy access for cleaning purposes. The shoes fitted to leg assembly help in aligning the structure for back to back arrangements. Levellers take cshould be of uneven flooring.Connecting beam should be fitted with snap locking end cap.lt also aids in side-by- side understructure alignment . Armrest assembly consshould be ts of armrest frame and armrest pad . The armrest frame should be made up of size 3.175±0.05cm x 0.47±0.027cm thk HR steel and it should be powder coated ( DFT 40-60 microns ). Armrest pad should be injection molded in Nylon and should be fitted onto the armrest frame. Overall Dimensions of Chair: Seat Height - 44.1 cm. Height - 78.5 cm. Width & Depth of Chair as - Width-169.5cm and Depth-63.8 cm. The cushions for seat and back should be made up of 1.5 ± 0.1 cm thk foam on a flat MR grade ply 0.8±0.04cm thk and should be upholstered with leatherite. Quality Certification: The manufacturer should have ISO 9001:2015, ISO 50001:2018, ISO 45001:2018, ISO 14001:2015 (All ISO certificate must be from NABCB/IAF recognized accreditation body), IGBC Platinum, AIOTA certification.

Providing, Supplying & Placing of 14-seater Conference Table. Work top--Made of 25mm thick MDF-one side pre-laminate board conforming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top and having chamfered edge. Access panels provided with soft closing hinges. Understructure- The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. The product has a knock-down construction. Wire Management-Bottom cabinet with door is provided for flow of wires and cables. Cutout provision below Access flap at four locations for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is provided for mounting Audio Visual Cables (eg. HDMI,VGA-A,etc). Quality Certification: The product should have Indoor Advantage Gold, GRIHA & SVAGRIHA, Greenpro, Greenguard (by UL) certification.

Providing, Supplying & Placing of High Back Chair with Headrest. SEAT/BACK ASSEMBLY: The seat is made up of 1.5 ±0.1cm. thick hot-pressedplywood and upholstered with fabric upholstery covers and moulded Polyurethane foam.The seat has extra thick foam on front edge to give comfort to popliteal area. The Back is injection moulded in glass filled Polypropylene which is upholstered withMesh fabric.The back consist of adjustable lumbar support made of injection mouldedPolypropylene having an adjustment of 5.0 ±0.1 cm. The chair seat & back size are, SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)*MESH BACK SIZE 51.0 cm. (W) x 70.0 cm. (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane seat foam is moulded with density 45±2 kg/m³ and hardness 16±2 kgf as per IS:7888 for 25% compression. ARMRESTS :The adjustable armrest is designed with the following features :· Up-Down adjustment– 6 steps (7.2 ± 0.5cm range). Armrest top is mounted on Armrest structure made of glass filled Nylon· Armrest Top is PU moulded over glass filled Nylon insert. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism isdesigned with the following features: 360° revolving type. 3-position locking with anti shock mechanism. Tilt tension adjustment. HEADREST: The Headrest sub-assembly is made up of injection moulded glass filledPolypropylene which is upholstered with moulded HR polyurethane foam and fabric. Ithas an adjustment of 4.0 ± 0.1cm & it is assembled over Thrill mesh back chair.The complete headrest assembly is retro fit to the main chair. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment with anadjustment stroke of 9.5 ± 0.3cm. PEDESTAL ASSEMBLY : The pedestal is injection moulded in glass-filled Nylon andfitted with 5 nos. twin wheel castors. The pedestal is 66.1 ±0.5cm. pitch-center dia.(76.1 ±1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 76.1 CM. DEPTH (D): 76.1 CM. HEIGHT (H): 117.0 - 130.0 CM. SEAT HEIGHT (SH): 44.5 - 54.0 CM. Quality Certification: The product should have Greenguard (by UL) & Indoor Advantage Gold certification.

Providing, supplying and placing of revolving mesh Back Chair. SEAT/BACK ASSEMBLY: The cushioned seat assembly consists of seat base moulded in glass-filled Poly-amide, moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The Back is injection moulded in glass filled Polypropylene which is upholstered with Mesh fabric. The back consist of adjustable lumbar support made of injection moulded Polypropylene having an adjustment of 3.0 ±0.1 cm. Mesh Back Size : 45.5 cm. (W) x 54.0 cm. (H). Seat Size : 48.5 cm. (W) x 49.0 cm. (D). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam used in seat and back cushion is moulded in Density Min 48 kg/m³, and hardness load 15 ± 2 kgf as per IS:7888 for 25% compression. TILT MECHANISM, SPINES & SPINE CONNECTOR: The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during posture changes. The "S" shaped spines moulded in high strength glass-filled Poly-amide and the spine connector moulded in glass-filled Poly-amide form the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt Limit feature which is inbuilt in seat base and the tension (return force) is user weight dependent. ADJUSTABLE ARMRESTS: The assembly consists of armrest housing sliding over the armrest structure, both moulded in glass-filled Poly-amide. The height adjustment feature is button operated having adjustment of 6.6±0.5cm. The Armrest Top is made up of integral skin PU moulded over plastic inner moulded in glass-filled Poly-amide. PNEUMATIC HEIGHT ADJUSTMENT: The seating height can be adjusted with a pneumatic gas-lift having an adjustment stroke of 9.2 ± 0.3 cm. PEDESTAL ASSEMBLY: The pedestal is injection moulded in glass-filled Poly-amide and fitted with 5 nos. twin wheel castors. The pedestal is 66.0±0.5 cm. pitch centre diameter and 76.0±1.0 cm. with castors. TWIN WHEEL CASTORS: 5 nos. twin wheel castors are injection moulded in Poly-amide having 5.0±0.1cm wheel diameter and assembled to the pedestal. Quality Certification: The product should have Greenguard, Indoor Advantage Gold, BIFMA Level-2 & Greenpro Certification.

Proving, Supplying & Placing of visitor mesh back chair. SEAT ASSEMBLY: The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood , upholstered with fabric upholstery covers and moulded Polyurethane foam. SEAT SIZE: 47.0 cm. (W) x 48.0 cm. (D). BACK ASSEMBLY: The back asembly. should be made of powder coated (OFT 40-60 microns) tubular frame of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using double layer spacer mesh fabric with high tenacity yarn. BACK SIZE : 46.5 cm. (W) x 60.5cm. (H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. ARMRESTS: The one-piece armrests should be injection moulded from black Co- polymer Polypropylene. TUBULAR FRAME: The powder coated (DFT 40-60.microns) tubular frame should be cantilever type & made of Ø2.54 ±0.03cm. x 0.2 ±0.016cm thick M.S.E.R.W. Tube. Overall Dimensions of Chair: Seat Height - 46.5cm. Height - 93.5cm. Width & Depth of Chair as measured from pedestal - Width-61.0 cm and Depth-64.5 cm. Quality Certification: The product should have Greenpro, Indoor Advantage Gold, GRIHA & SVAGRIHA certification.

Providing, Supplying & Placing of steel alimirah as per the following specification. The almirah shall have an overall size of 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available. Quality Certification: The product should have Greenguard (by UL), Indoor Advantage Gold, GRIHA & SVAGRIHA & Greenpro certification.

Providing and placing of Pentagonal Manager Module type panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1467.50 including powder coated aluminium trims. Tiles on main spine: Combination of top tiles are clear glass tile. Bottom tiles - Plain metal. INTERMEDIATE BLOCKS on main spine Intermediate blocks are given in DL + DL + FABRIC finsh. Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. MODESTY PANELS WITH ASSEMBLY LEG - 25 MM THK PLB modesty has been given on the front of the main worktop which is attached to the partition on one end with gable end bkts and on the other end with metal powder coated frontier leg. Legs - metal powder coated legs at the end and shared condition. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Worksurface - Main table recta out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1500 mm w x 600 mm d and ERU table recta of size 900 mm w x 450 mm d. Pedestals with legs - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. CPU trolley - with castors. KBPT with mousetray - metal. Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring. Note 2: SPECIFICATIONS OF FLOORING FOR THE FREE STANDING PARTITION :- GRADE OF PCC SHOULD BE MINIMUM OF M20 ( MIX RATIO 1:5:5:3) OR M25 (MIX RATIO 1:1:2). THE DIMENSION OF EACH PCC SHOULD BE 450 MM L X 300 MM W X 140 TO 150 MM HT AT THE MARKED LOCATION. ( MIX RATIO OF CEMENT: SAND: STONE). ALSO ELECTRICAL TRUNKING SHOULD NOT BE LAID BELOW THESE PARTITIONS. Quality Certification: The product should have Greenguard (by UL), Indoor Advantage Gold, GRIHA & SVAGRIHA, BIFMA Level-2 & Greenpro certification.

Providing and placing Rectangular spine and fin based modular workstation, with partition thickness as 52.4 mm thk and ht - 1467.50 including powder coated aluminium trims. FIN: out of 22.5 mm thk panel formed out of blocks which are 18 mm thk PLB boards wrapped with laminate & fabric at inter/fabric magnetic and fabric tackable finish. TBottom block is finished in metal finish. Tiles on main spine: Combination of top tiles are clear glass tile. Bottom tiles - Plain metal. INTERMEDIATE BLOCKS on main spine Intermediate blocks are given in DL + DL + FABRIC finish. Wire Management through main spine- Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. Worksurface - out of 25 mm thk prelam particle board with flat pvc lipping edge banding of size 1200 mm w x 600 mm d. Pedestals with legs - Nova pedestal flat metal front, full ht free standing central locking of size 390 mm w x 435 mm d x 646 mm ht 3dr = 2box+1file. CPU trolley - with castors. KBPT with mousetray - metal. Note: All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of +/- 40 mm of uneven flooring. Quality Certification: The product should have Greenguard (by UL), Indoor Advantage Gold, GRIHA & SVAGRIHA, BIFMA Level-2 & Greenpro certification.

Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured. ; upholstered with synthetic leather over moulded High Resilience Polyurethane foam. MID BACK SIZE: 51.6 cm. (W) x 65.7 cm. (H) , SEAT SIZE: 49.0 cm. (W) x 48.8 cm. (D). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS: The adjustable armrest is designed with the following features : • Up- Down adjustment– 8 steps (8.0±0.5cm range) • Height adjustable armrest structure which is chrome plated & fitted with an armrest top. • Fixed Armrest Top is PU moulded over metal insert. FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features.• 360° revolving type. • Single point control. • Front-pivot for tilt with feet resting on ground ensuring more comfort. • Tilt tension adjustment. • 4-position locking with anti-shock feature. • Seat/back tilting ratio of 1:2. BACK HEIGHT ADJUSTABILITY: Back can be adjusted in 5 positions by manually. Stroke of height adjustable spine is 7 cm. Back height adjustability is applicable for for High back and Mid back chair. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. PEDESTAL ASSEMBLY WITH CASTORS: The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTOR: The twin wheel castors are injection moulded in black PP. OPTION OF SLIDING SEAT MECHANISM : Seat can be slide horizontaly as per user convenience. Stroke of seat slide is 5 cm. This option is available for revolving pedstal type of chair. Overall Dimensions of Chair: Seat Height - min 45.0 to max 55.0cm. Height - min 92.0 to max 110.0 cm. Width & Depth of Chair as measured from pedestal - Width-750 cm and Depth-75.0 cm. Quality Certification: The manufacturer should have ISO 9001:2015, ISO 50001:2018, ISO 45001:2018, ISO 14001:2015 (All ISO certificate must be from NABCB/IAF recognized accreditation body), IGBC Platinum, AIOTA certification.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured. ; upholstered with synthetic leather over moulded High Resilience Polyurethane foam. HIGH BACK SIZE: 51.8 cm. (W) x 75.2 cm. (H) , SEAT SIZE: 49.0 cm. (W) x 48.8 cm. (D). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =55+/-2 kg/m³ and hardness 16 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS: The adjustable armrest is designed with the following features : • Up- Down adjustment– 8 steps (8.0±0.5cm range) • Height adjustable armrest structure which is chrome plated & fitted with an armrest top. • Fixed Armrest Top is PU moulded over metal insert. FRONT PIVOT SYNCHRO MECHANISM: The adjustable tilting mechanism is designed with the following features.• 360° revolving type. • Single point control. • Front-pivot for tilt with feet resting on ground ensuring more comfort. • Tilt tension adjustment. • 4-position locking with anti-shock feature. • Seat/back tilting ratio of 1:2. BACK HEIGHT ADJUSTABILITY: Back can be adjusted in 5 positions by manually. Stroke of height adjustable spine is 7 cm. Back height adjustability is applicable for for High back and Mid back chair. PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3 cm. PEDESTAL ASSEMBLY WITH CASTORS: The pedestal is High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTOR: The twin wheel castors are injection moulded in black PP. OPTION OF SLIDING SEAT MECHANISM : Seat can be slide horizontaly as per user convenience. Stroke of seat slide is 5 cm. This option is available for revolving pedstal type of chair. Overall Dimensions of Chair: Seat Height - min 45.0 to max 55.0cm. Height - min 102.0 to max 119.0 cm. Width & Depth of Chair as measured from pedestal - Width-750 cm and Depth-75.0 cm. Quality Certification: The manufacturer should have ISO 9001:2015, ISO 50001:2018, ISO 45001:2018, ISO 14001:2015 (All ISO certificate must be from NABCB/IAF recognized accreditation body), IGBC Platinum, AIOTA certification.

Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY : The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with pure leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression.The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Pure Leather. Seat SIZE : 47.6 cm. (W) x 49.2 cm. (D), BACK SIZE : 47.5 cm. (W) x 77 cm. (D). ARMRESTS: The armrest top should be moulded from polyurethane(PU), upholstered in pure leather and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism should be designed with the following features: 360° revolving type. Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. Tilt tension adjustment can be operated in seating position. 5-position Tilt limiter giving option of variable tilt angle to the chair. Seat/back tilting ratio of 1: 2. The mechanism housing should be made up of HPDC Aluminium black powder coated. SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0±0.3 cm.. PEDESTAL ASSEMBLY The pedestal should be High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTORS:The twin wheel castors should be injection moulded in Black Polypropylene. Overall Dimensions of Chair: Seat Height -44.5 to 54.5 cm., Height -114.0-131.5 cm,.Width & Depth of Chair as measured from base - Width-76.1 cm and Depth-76.1 cm Quality Certification: The product should have Greenguard (by UL), Indoor Advantage Gold, GRIHA & SVAGRIHA, BIFMA Level-2 & Greenpro certification.

Supplying and placing in position Back unit of the following specifications.1800x500x1100 Top Panel- Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Slide Door Unit-Made of 25mm Thick Pre-laminated twin board of E1- P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves. Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening.Storage is provided with lock for security. Quality Certification: The product should have Greenguard (by UL), Indoor Advantage Gold, GRIHA & SVAGRIHA & Greenpro certification.

Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987. xiii) 12mm thick cleared toughened glass coforming to IS: 2553-1992 (Part-II)