Central Glass And Ceramic Research Institute Tender

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : Two or more coats on new work. New work (two or more coats) over and including water thinnable priming coat with cement primer.

Wall panelling / partition with Melamine faced 3 layered flat pressed wood particle board of approved make and brand as per direction of Engineer - in - Charge of requisite grade bonded with phenol formaldehyde synthetic resin conforming to IS: 848 - 1974 (excluding the cost of supporting frame work and teak wood battens / lipping) In GroundFloor. Prelaminated particle board conforming to IS: 3087 - 1985 and IS 12823 - 1990. Both side decorative laminated. Exteriorgrade. 9mm thick

Godrej Hydraulic door closer fitted and fixed complete. Heavy type

Providing & fixing mortice lock 4-lever narrow stile for aluminium door(sliding/openable) product code 9158 Baan code 46171598SD00419 all complete as per direction.

Laboratory Table with Granite Top Providing and placing laboratory table with Granite Top as per following specification: Table top must be rest on a frame and a middle support placed width wise. Each table to be rest on four legs. The frame and legs should be made of square MS frame of size 2" x 2" hollow type with 16 gauge sheet. The table consists of two nos. drawer with locking arrangement and cabinet with one shelf in each. Cabinet doors must open front side. Each cabinet should be separated from each other using a partition wall made of same sheet. Total structure and body of the cabinet should be epoxy powder coated (7 tanks) by grey and blue colour. 02mm rubber pad will be fitted on the top of the table along with 18mm polished granite slab (dimension must be adjusted).

Size 60" length x 36" width x 32" height

Size 48" length x 30" width x 32" height

Granite Top Providing & placing 18mm polished granite slab over existing wooden table as per direction complete.

Size: 48" length X 30" width

Size: 49" length X 36" width

Size: 93" length X 30" width

Size: 60" length X 37" width

Size: 96" length X 36" width (Granite top will be fitted in two parts)

Size: 96.5" length X 36" width (Granite top will be fitted in two parts)

Size: 96.5" length X 30" width (Granite top will be fitted in two parts)

Rates are inclusive of all taxes