Uttarakhand Jal Vidyut Nigam Limited Tender

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete. Made of G.I. wire of dia 4 mm. Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Type - A, "W" : Metal Beam Crash Barrier (Providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete. Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Foundations, footings, bases of columns, etc. for mass concrete. Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand). Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm. Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand).Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Stone masonry in cement mortar for substructure complete. In 1:4 cement mortar.Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil. Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately). Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Mild steel and Medium Tensile steel bars. Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Removal of debris / waste material / rubbish on road side /dismantaled refuses/ park / dust bin and from any other location by full load tractor trolly within the specified colonies as desired by the Engineer-in-charge & safe disposal of the same out side the colony area .Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Hire charges of welding machine with single phase with welder, helper and electrodes etc. for repair and welding of gates, door, window etc. for 8 hrs. in a day complete with all material labour, T&P etc. required for proper completion of work. Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads.The finished surface to be level, uniform and free from streaks and holes). Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

PVC Traffic Cones (750 mm height): Supply of PVC Traffic Cones of 750 mm height and 3.5 kg weight with square base and 3 strips of 10 mm wide reflective sheets around the cone.Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Retro- reflectorised Traffic signs (Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign made of encapsulated lens type reflective sheeting vide, fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing.60 cm x 45 cm rectangular. Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Engaging & operation of one no.Hydraulic excavator cum loader machine (preferably JCB)having capacity 75 BHP with one operator and one helper, including cost of fule lubricants and repair maintenance etc. for removal of slip/landslide/excavation in dry and wet condition, complete in all respect as per direction of I/C. Including supply of all material, labour,T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Road Studs / Cat Eye: Providing and fixing Bi-directional Road Studs (Cat Eye) / Reflective Pavement Marker (RPM) with single body twin shank and plastic body moulded from ASA (Acrylic Styrene Acrylonitrite) or HIPS (Hi-impact Polystyrene) or ABS (Acrylonitrile Butadiene Styrene) or any othersuitable material approved by Engineer in charge (Marker must support a load of 13635 kg tested in accordance with ASTM D 4280 and Reflective lenses conforming to ASTM D 788 or equivalent) bonded or anchored within the road surface for lane marking and delineation for night time visibility. The RPM must have reflective panels with micro prismatic lens where area of each retro reflective surface shall not be less than.Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Solar Road Studs: Providing and fixing Solar Powered Road Studs (Rectangular) of size not less than 100mm x 100 mm x 10 mm or (Circular) of dia 130+/- 6mm and height 30 +/- 2mm (with 8 super bright LEDs for long visibility from distance greater than 800 m) having twin shank and body made of aluminium alloy and poly carbonate material which shall be absolutely weather resistant and strong enough to support a load of 13635 kg tested in accordance with ASTM D 4280 and water resistance , fixed to the road surface using adhesives and the procedure recommended by the manufacturer. Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Road Delineators / Vertical Guide Posts: Supply andfixingof MSdelineators 1000mm long, having a diameter of 75 mm and thickness 4mm and having atleast 3 different colour strips of 75 mm wide Type IV retroreflective tape around the black painted pole attached with 150 mm x 25 mm x 6 mm MS flats welded atbottom to be fixed in M15 concrete base as directed by the Engineer in Charge. (Recommended Practice for Road Delineators). Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Direction and Place Identification Signs upto 0.9 sqm Size Board. Providing and erecting direction and place identification sign with corrosion resistant 2mm thick Type IV retro- reflective cautionary, mandatory, informatory sign board with 7 year warranty made of high intensity sheeting fixed over ACP (Aluminium Composite Panel) 3 mm thick (including framing and bracing with fabrication, plotting, pasting, riveting, taping and nut, bolts, washers and rivets etc for fixing) with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level .Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Rumble Strips. Provision of rumble strips of premix bituminous carpet, 25 mm high at centre, 300 mm wide placed at 1 m centre-to-centre at approved locations to control speed, marked with white strips of road marking paint.Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Direction and Place Identification Signs upto 0.9 sqm Size Board. Providing and erecting direction and place identification sign with corrosion resistant 2mm thick DG Grade Type XI retro- reflective cautionary, mandatory, informatory sign board with 10 year warranty made of high intensity sheeting fixed over ACP (Aluminium Composite Panel) 3 mm thick (including framing and bracing with fabrication, plotting of letters on Electro cut film, pasting, riveting, taping and nut, bolts, washers and rivets etc for fixing), with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level . Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Direction and Place Identification Signs with size more than 0.9 sqm size Board. Providing and erecting direction and place identification sign with corrosion resistant 2mm thick DG Grade Type XI retro- reflective cautionary, mandatory, informatory sign board with 10 year warranty made of high intensity sheeting fixed over ACP (Aluminium Composite Panel) 4 mm thick (including framing and bracing with fabrication, plotting of letters on Electro cut film, pasting, riveting, taping and nut, bolts, washers and rivets etc for fixing), with area exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing. Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Overhead Signs Providing and erecting overhead signs with a corrosion resistant 2mm thick DG Grade Type XI retro- reflective sheeting with 10 year warranty made of high intensity sheeting fixed over ACP (Aluminium Composite Panel) 4 mm thick (including framing and bracing with fabrication, plotting of letters on Electro cut film, pasting, riveting, taping and nut, bolts, washers and rivets etc for fixing), installed over a designed support system of aluminium alloy or galvanised steel trestles and trusses of sections and type as per structural design requirements and approved plans issued in original by retro-reflective sheeting manufacturer having operations in India by their indian subsidary.Truss and Vertical Support. Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.

Overhead Signs Providing and erecting overhead signs with a corrosion resistant 2mm thick DG Grade Type XI retro- reflective sheeting with 10 year warranty made of high intensity sheeting fixed over ACP (Aluminium Composite Panel) 4 mm thick (including framing and bracing with fabrication, plotting of letters on Electro cut film, pasting, riveting, taping and nut, bolts, washers and rivets etc for fixing), installed over a designed support system of aluminium alloy or galvanised steel trestles and trusses of sections and type as per structural design requirements and approved plans issued in original by retro-reflective sheeting manufacturer having operations in India by their indian subsidary.Truss and Vertical Support.Type IV HIP retro- reflective sheeting for Over Head Sign.Including supply of all material, labour, T&P etc required for proper completion of the work as per direction of Engineer-in -Charge.