Sashastra Seema Bal Tender

Painting on G.S Sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: New work (two or more coats0 including a coat of approved steel primer but excluding a coat of mordant solution

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-ChargeWith cement mortar 1:4 (1 cement : 4 fine sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level: 1:4:8 (1 cement : 4 coarse sand (zone-III) derived from natural source :8 grade stone aggregate 40mm nominal size derived from natural sources.

Providing and laying ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in colours such as white, ivory, grey, fume red brown laid on 20mm thick cement mortar 1:4 (1 cement:4 coarse sand ), jointing with grey cement slurry @3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. complete.

Providing & fixing water closet squatting pan 9Indian type W.C. pan) with 100 mm sand cast iron P or S trap, 10 litre low level white PVC flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to 15 7231 with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White vitreous china orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing bright finished brass handles with screws etc. complete: 125 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 15 mm nominal dia Pipes

20 mm nominal dia Pipes

25 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 100 mm nominal dia Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 20 mm nominal bore

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 15 mm nominal bore

25 mm nominal bore

Providing & fixing unplasticised PVC connection pipe with brass unions; 30cm long 15mm nominal bore

Providing and fixing PTMT pillar cock of approved quality and colour. 15mm nominal bore, 107mm long weighing not less than 110gms

Providing & fixing PVC waste pipe for sink or wash basin including PVC waste fitting complete. Flexible pipe 40 mm dia.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity - White

Providing & fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour; 450mm long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 1170gms.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap

Renewing glass panes, with putty and nails where ever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10 kg/sqm)

Providing & fixing false ceiling at all height including providing & fixing of all framework made of special section, power pressed from M.S. sheets and galvenised with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleat of size 25mm wide X 1.6mm thick with flanges of 27mm and 37mm, at 1200 mm c/c, one flanged fixed to the ceiling with dash fastener 12.5 mm dia X 50mm long with 6mm dia volts, other flange of leat fixed to the angle hangers of 25 x10 x0.50 mm of required length with nuts & volts of required size and other end of angle hanger fixed with internediate G.I. channel 45x15x0.90 mm running at spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.5 mm at 450mm c/c shall be fixed in a direction perpendicular to G.I. intermediate channel, with connecting clip made out of 2.64 mm dia x 230mm long G.I. wire at every juctionincluding fixing perimeter channels including 050 mm thick 27 mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to the wall/partition with the help of rawl plugs at 450mm centre with 25 mm long dry wall screw @230mm interval, including fixing of calcium silicate board to ceiling section and perimeter channels with the help of dry wall screw of size 3.5x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes with jointing compounds in three layer covering upto 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitable fixed, all complete as per drawings specifications and direction of the Engineer in charge but excluding the cost of painting with: 8 mm thick calcium silicate board made with calcareous & siliceous materials reinforced with cellulose fiber manufactured through autoclaving process

35 mm thick factory made Solid panel PVC Door shutter, made out of single piece extruded soild PVC profiles, 5 mm (± 0.2 mm) thick, having styles & rails (except lock rail) of size 95 mmx 35 mm x 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered (on both side), having one side thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20 mm x 1 mm, joints of styles & rails to be mitered cut & joint with the help of PVC solvent cement, self driven self tapping screws & M.S. rectangular pipes bracket of size 190 mm X 100 mm of cross section size 35 mm x 17 mm x 1 mm at each corner. Single piece extruded 5 mm thick solid PVC Lock rail of size 115 mm x 35 mm, out of which 75 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles & rails with the help of solvent and self driven self tapping screws of 125 mm x 11 mm, including providing 5 mm Single piece solid PVC extruded sheet inserted in the door as panel, all complete as per manufacturer's specification and direction of Engineerin-charge. Non decorative finish (matt finish)

ELECTRICAL WORK

Supplying & fixing piano type switch/socket on the existing switch/box cover including connections etc. as required. 5/6 amps switch

3 pin 5/6 A socket outlet

Supplying & fixing brass batten/ angle holder including connection etc. as required.

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surfaced /recessed steel/pvc conduit as required 1x1.5 sqmm

2x2.5 sqmm

2x4 sqmm

2x6 sqmm

15/16 A switch

Add Cost Index @8.41% on SR&DR