Rural Works Department Tender

Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Hot rolled twisted bars.

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete.Raj nagar plain white marble/ Udaipur green marble/ Zebra black marble8 mm thick

Providing, assembling and supplying vision glass panels (IGUs)comprising of hermetically-sealed 6-12- 6 mm insulated glass (doubleglazed) vision panel units of size and shape as required and specified,comprising of an outer heat strengthened float glass 6 mm thick, ofapproved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass6 mm thick, spacer tube 12 mm wide, dessicants, including primary sealand secondary seal (structural silicone sealant) etc. all complete for therequired performances, as per the Architectural drawings, as per theapproved shop drawings, as specified and as directed by the Engineerin- Charge. The IGUs shall be assembled in the factory/ workshop of theglass processor(Payment for fixing of IGU Panels in the curtain glazing is included in costof item No.25.2)For payment, only the actual area of glass on face # 1 of the glass panels(excluding the areas of the grooves and weather silicone sealant) providedand fixed in position, shall be measured in sqm.(i) Coloured tinted float glass 6 mm thick substrate with reflective softcoating on face # 2, + 12 mm Airgap + 6 mm Heat Strengthened clearGlass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflectionexternal 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0to 3.3 W/m2 degree K etc. The properties of performance glass shall bedecided by technical sanctioning authority as per the site requirement.

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 10.30.2 5.5 mm thick glass panes

Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/ appropriate Zsections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, includingnecessary filling up the gaps at junctions, i.e. at top, bottom and sideswith required EPDM rubber/ neoprene gasket etc. Aluminium sectionsshall be smooth, rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as perarchitectural drawings and the directions of Engineer-in(Glazing, paneling and dash fasteners to be paid for separately) :Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)21.1.2.2 Powder coated aluminium (minimum thickness of powder coating 50 micron)

12 mm cement plaster of mix. 1:6 cement and fine sand mortar.

supply and fixing of mute pro u shape baffle ceiling made .50mm thick G.I with powder coating in solid RAL colour in approved shade of size 100*50mm at spacing 150mm c/c inclusive of gi suspension system

Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanitycounters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cementmortar 1:4 (1 cement:4 coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, including rubbing, curing,moulding and polishing of edges to give high gloss finish etc. completeat all levels.Granite stone slab of colour black, Cherry/Ruby redArea of slab upto 0.50 sqm

Providing and fixing Brass 100 mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-charge

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS:3564, embossed on the body, door weight upto 35 kg and door width upto 700mm), with necessary accessories and screws etc. complete.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6graded stone aggregate 20mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

Providing and fixing Ist quality ceramic glazed wall tiles conf IS : 15622 (thickness to be specified by the manufacture ) of appr make in all colours, shades except burgundy, bottle green, black of size as approved by Engineer-in-Charge in skirting, risers of ste dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 c sand) and jointing with grey cement slurry @ 3.3kg per sqm i pointing in white cement mixed with pigment of matching sh complete.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5mm with top and bottom rail of T-iron 40x40x6mm with 40mm pulleys complete with bolts, nuts, locking arrangement, stopp handles, including applying a priming coat of approved steel prime

Finishing walls with Acrylic Smooth exterior paint of required shade :13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqmover and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

13.62 Painting with synthetic enamel paint of approved brand andmanufacture of required colour to give an even shade :13.62.1 Two or more coats on new work over an under coat ofsuitable shade with ordinary paint of approved brand and manufacture

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of sizeSize of Tile 800 x 1200 mm

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Iinternal work - Exposed on wall15 mm dia. nominal bore

Providing and fixing brass stop cock of approved quality15 mm nominal bore

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 17.10.1 Kitchen sink with drain board 17.10.1.1 510x1040 mm bowl depth 250 mm

Providing and fixing ball valve (brass) of approved quality completeHigh or low pressure with plastic floats15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene w tank ISI : 12701 marked with cover and suitable locking arrangem necessary holes for inlet, outlet and overflow pipes but without fitti base support for tank

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:893115 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15mm nominal bore.

Providing and fixing mirror of superior glass (of approv quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. with plastic moulded frame of approved make and shades with 6 mm thick hard board backing:Rectangular shape 453x357mm

Constructing brick masonry chamber for underground C.I. inspecti and bends with 75 class designation bricks in cement mortar 1:4 ( coarse sand) C.I. cover with frame (light duty) 455x610 mm intern total weight of cover with frame to be not less than 38 kg (weight and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 ceme sand : 4 graded stone aggregate 20 mm nominal size) foundation (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nomin plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 coar smooth with a floating coat of neat cement on walls and bed concr complete as per standard design :With F.P.S. bricksInside dimensions 455x610 mm and 45 cm deep for single pipe line :

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32White Vitreous China Flat back wash basin size 550x400 mm with brass pillar tap.

Providing and fixing on wall face unplasticised Rigid PVC rain water conforming to IS : 13592 Type A including jointing with seal ring c 5382 leaving 10 mm gap for thermal expansion, (i) Single sockete75 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conformingto IS : 13592 Type A, including jointing with seal ring conforming toIS : 5382, leaving 10 mm gap for thermal expansion. 12.42.1 Coupler 12.42.1.1 75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittin for unplasticised Rigid PVC rain water pipes conforming to IS : 135 including jointing with seal ring conforming to IS : 5382 leaving 10 thermal expansion.Bend 87.5°,75 mm bend

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Smooth finishing of the exposed surface of R.C.C. work with 6 mm thickcement mortar 1:3 (1 Cement : 3 fine sand).

Providing and fixing factory made Kitchen Cabinet Shutter/Partition 20 mm nominal thickness of approved shade, quality and make, made from rigid foam sheets (Single extruded) having density 600 Kg/cumand laminated on both side by laminate Sheet/PVC foil lamination. Theexposed edges shall be sealed with PVC edge beading of same shadeand colour. The shutter shall be fire retardent having necessary screwholding capacity. Shutter shall be fixed to frame using approved hinges with necessary stainless steel screws, all complete as per direction ofEngineer-in-charge

Excavation in ordinary Rock by manual means 3-8-1 Excavation in ordinary rock using manual means including loading in a truck and carrying of excavated material to embankment site with a lift upto 1.5 m and lead upto 50 m as per Technical Specification Clause 302.3.5.

Cement plum Masonry with 40% plum & 60% 1:3:6 cement concrete including supply of all material, labour, T&P etc. required for proper completion of the work. as per drawings and technical specifications Clause 802, 803, 1202 & 1203 of MORD Specifiction

Random Rubble Stone Masonry laid in 1:6 cement and sand mortar, inbreast walls, retaining walls, parapets, scuppers, etc. including supply ofall material, labour, T&P and royaltiies etc. complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203 of MORD Specifiction

Hand Packed stone filling in back of wallls including cost of all materials, royality, T&P etc. complete as per direction of Engineer-in- charge. (As per PWD Uttarakhand specifications)