Power Transmission Corporation Of Uttarakhand Limited Tender
View complete overview of Uttarakhand PTCUL Tender
Power Transmission Corporation Of Uttarakhand Limited - PTCUL Tender
Civil And Construction
Building Construction
Eprocure
Opening Date16 Mar 2024
Closing DateCancelled
Tender AmountRefer Documents
Costs
EMD
₹ 75,000Document Cost
₹ 1,180Tender Fee
Refer Documents
Summary
Annual Mandr Works Yamuana Colony
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_PTCU8_71424_1Tender No
48_SEC_OandM_PTCULTender Authority
Power Transmission Corporation Of Uttarakhand Limited ViewPurchaser Address
-Website
http://https://www.ptcul.org
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
10
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)
20
-
-
Providing and laying cement concrete in kerbs, steps and the like at or near ground level excluding the cost of centering, shuttering and finishing.1:1½:3 (1 Cement: 1½ coarse sand(zone-III) derived from
natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
2
-
-
Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from
natural sources)
50
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
2.5
-
-
Reinforced cement concrete work in walls (any thickness), includingattached pilasters, buttresses, plinth and string courses, fillets, columns,pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost ofcentering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from naturalsources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources)
2.5
-
-
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).
2.5
-
-
Centering and shuttering including strutting,propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete.
30
-
-
Centering and shuttering including strutting propping etc. and removal of form for:Walls(any Thickness) including attached pillasters, butteresses plinth and string courses etc.
20
-
-
Centering and shuttering including strutting propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platform.
50
-
-
Centering and shuttering including strutting propping etc. and removal of form for: Shelves Cast in situ
10
-
-
Centering and shuttering including strutting propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts
10
-
-
Centering and shuttering including strutting propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases
10
-
-
Centering and shuttering including strutting propping etc. and removal of form for Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like
10
-
-
Centering and shuttering including strutting, propping etc. and removal of form for Edges of slabs and breaks in floors and walls Under 20 cm wide
10
-
-
Centering and shuttering including strutting propping etc. and removal of form for: Weather Shade, Chajjas,Corbeles etc. including edges.
20
-
-
Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits.40 mm thick
10
-
-
Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level. Mild steel and Medium Tensile steel bars
100
-
-
Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete above plinth level. Mild steel and Medium Tensile steel bars
100
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 ( 1 cement : 6 coarse sand)
2.5
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level inall shapes and sizes in :6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand)
5
-
-
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 ( 1 cement : 4 coarse sand)
20
-
-
Providing and fixing 18 mm thick gang saw cut,mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble.Area of slab upto 0.50 sqm.
1
-
-
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby red Area of slab upto 0.50 sqm
1
-
-
Providing edge moulding to 18 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge (Marble work)
2
-
-
Providing edge moulding to 18 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge (Granite work)
5
-
-
Providing and fixing expandable fasteners of specified size with necessary plastic sleeves and galvanised M.S. screws including drilling holes in masonry work /CC/ R.C.C. and making good etc. complete. (40 mm long) -
15
-
-
8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
20
-
-
Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).: (Sal wood)
0.25
-
-
Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S.Pressed butt hinges bright finished of required size with necessary screws.Second class teak wood (35 mm thick)
2.5
-
-
Providing and fixing 25 mm thick shutters for cup board etc. :Panelled or panelled & glazed shutters :Second class teak wood including ISI marked anodised aluminium butt hinges with necessary screws.
2.5
-
-
Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: (35 mm thick including ISI marked Stainles steel butt hinges with necessary screws.)
10
-
-
Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :with ISI marked M.S. pressed butt hinges bright finished of required size(Second class teak wood)
5
-
-
Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete.2nd class teak wood (50x12mm )
20
-
-
Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete.2nd class teak wood (50x20mm)
5
-
-
Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : 20 mm dia ( heavy type)
10
-
-
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding
20
-
-
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etc.
20
-
-
Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wiregauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete.With 2nd class teak wood beading 62X19 mm
15
-
-
Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wiregauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete With 12 mm mild steel U beading .
5
-
-
Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size)..
25
-
-
Providing and fixing ISI marked IS : 1341 M.S. pressed butt hinges bright finished with necessary screws etc. complete :125x65x2.12 mm
20
-
-
Providing and fixing ISI marked IS : 1341 M.S. pressed butt hinges bright finished with necessary screws etc. complete : 100x58x1.90 mm
50
-
-
Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete: (75 x 47x1.70mm)
20
-
-
Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : (copper oxidized as per IS: 1378) 300x16 mm
20
-
-
Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : (copper oxidized as per IS: 1378) 250x16 mm
25
-
-
Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : (copper oxidized as per IS: 1378) (250x10mm)
15
-
-
Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : (copper oxidized as per IS 1378)200x10 mm
15
-
-
Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete. (150x10mm)
10
-
-
Providing and fixing ISi marked oxidised M.S. door latches conforming to IS:5930 with screws etc. complete : (copper oxidized as per IS:1378) 300x20x6 mm
5
-
-
Providing and fixing ISi marked oxidised M.S. door latches conforming to IS:5930 with screws etc. complete : (copper oxidized as per IS:1378) 250x20x6 mm
5
-
-
Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : (copper oxidized as per IS: 1378)125 mm
10
-
-
Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : (copper oxidized as per IS: 1378)75 mm
5
-
-
Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.
5
-
-
Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.
2
-
-
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :300x10 mm
2
-
-
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :250x10 mm
2
-
-
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :200x10 mm
2
-
-
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm
2
-
-
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :75 mm
2
-
-
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Single rubber stopper
2
-
-
Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat.Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.
15
-
-
Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protectivesurface layer and reverse side of adhesive bonding quality conforming
to IS : 2046 Type S, including cost of adhesive of approved quality 1.0 mm thick
15
-
-
Providing and fixing factory made Fiberglass Reinforced plastics (F.R.P.) chajja 4 mm thick of required colour, size and design made by Resin Transfer Moulding (RTM) Machine Technology, resulting in void free compact laminate in single piece, having smooth gradual slope curvature for easy drainage of water and duly reinforced by 2 nos vertically and 1 nos horizontally 50x2 mm thick M.S. flat with 12 mm in uilt hole for grouting on the existing wall along with the 50 mm flanges duly inserted and sealed in the wall complete in one single piece casted monolithically, including all necessary fittings . The FRP Chajja should be manufactured using unsaturated Polyester resin as per IS: 6746, duly reinforced with fibre glass chopped strand mat (CSM) as per IS: 11551 complete with protective Gel coat U/V coating on Top for complete resistance from the extreme of temperature, weather & sunlight (Only plan area of chajjas shall be measured for making payment)
2
-
-
Providing and fixing in wall lining medium density fibre board IS:
14587:1998 marked, Pre-laminated one side decorative lamination and
other side balancing lamination, with necessary fixing arrangement and
screws etc. complete 18 mm thick.
5
-
-
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position andapplying a priming coat of approved steel primer all complete.
150
-
-
Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using flats 30x6mm for diagonal braces and central cross piece
5
-
-
Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means,including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Profile B Fixing with adjustable lugs with split end tail to each jamb
50
-
-
Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means,including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Profile C
Fixing with adjustable lugs with split end tail to each jamb
25
-
-
Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means,including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Profile E Fixing with adjustable lugs with split end tail to each jamb
15
-
-
Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse
sand : 6 graded stone aggregate 20 mm nominal size)
25
-
-
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
Hot finished welded type tubes
50
-
-
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works
45
-
-
Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.M.S. tube
25
-
-
Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. G.I. pipes
50
-
-
Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides
15
-
-
Providing & fixing glass panes with putty and glazing clips in steel doors,windows, clerestory windows, all complete with :4.0 mm thick glass panes (weights not less than 10 kg/ sqm)
10
-
-
Providing and fixing angle iron frames for doors, windows and ventilators of mild steel angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge.
50
-
-
Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks:1:6 (1cement : 6 coarse sand)
10
-
-
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. (40 mm thick with 20mm nominal size stone aggregate).
20
-
-
Cement concrete pavement with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete.
0.5
-
-
Providing and fixing glass strips in joints of terrazo/ cement concrete floors.40 mm wide and 4 mm thick
20
-
-
Tile work in skirting, risers of steps and dado up to 2 m height over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm, including pointing in
white cement mixed with pigment of matching shade complete.Marble tiles (polished) Raj Nagar 8 mm thick
1
-
-
Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with :Udaipur green marble
1
-
-
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick
1
-
-
Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
0.5
-
-
Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey,Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc.,complete.
10
-
-
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Double charge vitrified tile polished finish of size Size of Tile 600 x 600 mm
50
-
-
Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : (in 75x75mm deep chase)
5
-
-
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter
20
-
-
Providing & fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss
members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work
shall be paid separately).0.71 mm, Aluminium Color coated troughed profile with center to center pitch of 200 mm, depth of 32 mm, overall profile width1092 mm, cover width 1000mm.
20
-
-
12mm cement plaster of mix: 1:6 (1cement : 6coarse sand) )
100
-
-
15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1cement : 6coarse sand) )
50
-
-
6 mm cement plaster 1:3 (1 cement : 3 fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams.
50
-
-
Neat cement punning
15
-
-
Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete..
800
-
-
Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water thinnable priming coat with cement primer
150
-
-
Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work
300
-
-
Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable Cement primer
100
-
-
Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)) :
100
-
-
Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
500
-
-
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : :Two or more coats on new work :
300
-
-
Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete
150
-
-
Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade :Old work (one or more coats).
100
-
-
Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.
100
-
-
Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work.
100
-
-
Distempering with 1st quality acrylic distemper (ready made) having VOC content less than 50 gm per ltr. of approved manufacturer and of required shade and colour complete. as per manufacturer's
specification. One or more coats on old work
100
-
-
Finishing walls with water profing cement paint of required shade: Old work (one or more coats aplied @ 2.20kg/10sqm) over priming coat of primer applied @ 0.80 ltrs/10sqm. Complete including cost of priming coat.
100
-
-
Finishing walls with Acrylic Smooth exterior paint of required shade :Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface).DSR-
100
-
-
Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)
10
-
-
Renewal of old putty of glass panes (length)
50
-
-
Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete
8
-
-
Providing and fixing bright finished brass helical door spring (superior quality).
8
-
-
Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscocity 70 - 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical
parameters of the membrane shall be as under : Joint strength in
longitudinal and transverse direction at 23°C as 350/300 N/5 cm.
Tear strength in longitudinal and transverse direction as 60/80N.
Softening point of membrane not less than 150°C. Cold flexibility
shall be upto -2°C when tested in accordance with ASTM, D - 5147.
The laying of membrane shall be got done through the authorised
applicator of the manufacturer of membrane :
3 mm thick
25
-
-
14.92 Extra for covering top of membrane with Geotextile, 120 gsm non woven, 100% polyester of thickness 1 to 1.25 mm bonded to the membrane with intermittent touch by heating the membrane by Butane Torch as per manufactures recommendation.
25
-
-
Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)
1
-
-
Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.
0.25
-
-
Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. (In cement mortar ).
1
-
-
Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : : Of area 3 sq. metres and below
1
-
-
Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.
100
-
-
Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used..With G.I Barbed wire.
10
-
-
Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked black solid plastic seat and lid.
5
-
-
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:: White Vitreous china Flat back wash basin size 550x400mm with Single 15mm C.P. brass pillar tap.
10
-
-
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board 610x 510 mm bowl depth 200 mm..
2
-
-
Providing and fixing white vitreous china water closet squatting pan (Indian type ) Orissa pattern W.C. pan of size 580x440mm
5
-
-
Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 10 litre capacity-White
5
-
-
Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : Flat back wash basin of size 550 x 400 mm
10
-
-
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fitttings complete. Flexible pipe 32mm.dia
20
-
-
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
5
-
-
Providing and fixing soil, waste and vent pipes: 100mm dia( Sand cast iron S&S pipe as per IS:1729)DSR-
10
-
-
Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm dia Sand cast iron S&S as per IS - 1729
10
-
-
Providing and fixing plain bend of required degree. 100 mm dia Sand cast iron S&S as per IS - 1729
10
-
-
Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100mm inlet and 75 mm outlet Sand cast iron S&S as per IS - 1729
5
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge:20 mm nominal dia Pipes
50
-
-
Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc. Internal work -Exposed on wall 15 mm dia nominal bore
15
-
-
Providing and fixing G.I. pipes complete with G.I. fittings and clamps,i/c cutting and making good the walls etc. Internal work -Exposed on wall. 20 mm dia. nominal bore)
15
-
-
Providing and fixing G.I. pipes complete with G.I. fittings and clamps including cutting and making good the walls etc. Internal work -Exposed on wall. 25 mm dia. nominal bore)
15
-
-
Providing and fixing G.I. pipes complete with G.I. fittings including trenching & refilling etc. External work 15 mm dia. nominal bore)
30
-
-
Providing and fixing G.I. pipes complete with G.I. fittings including trenching & refilling etc. External work 20 mm dia. nominal bore)
15
-
-
Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 25mm dia nominal bore
15
-
-
Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 50 mm dia nominal bore
15
-
-
Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 65 mm dia nominal bore
15
-
-
Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 80 mm dia nominal bore
15
-
-
Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore .
5
-
-
Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee. Including cutting and threading the pipe etc. complete: 50mm to 80mm nominal bore .
5
-
-
Providing and fixing ball valve (brass ) of approved quality High or low pressure, with plastic floats complete: 15mm nominal bore
10
-
-
Providing and fixing Unplasticised PVC connection Pipe with brass unions. 45 cm length :15 mm nominal bore
15
-
-
Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 15mm nominal bore.
20
-
-
Providing and fixing G.I. Union in G.I. Pipe , including cutting and threading the pipe and making long screws etc. complete (new work): 20 mm nominal bore.
10
-
-
Providing and fixing G.I. Union in G.I. Pipe , including cutting and threading the pipe and making long screws etc. complete (new work): 50 mm nominal bore.
2
-
-
Providing and fixing G.I. Union in G.I. Pipe , including cutting and threading the pipe and making long screws etc. complete (new work): 80 mm nominal bore.
2
-
-
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow
pipes but without fittings and the base support for tank
2000
-
-
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:15mm nominal bore
45
-
-
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore
45
-
-
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore
3
-
-
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm nominal bore
10
-
-
Supplying and fixing C.I. cover without frame for manholes 455x610 mm rectangular C.I. cover (light duty) the weight of the cover to be not less than 23 kg
4
-
-
Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Rectangular shape 600x450 mm internal dimensions
1
-
-
Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Square shape 450 mm internal dimensions
1
-
-
Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Circular shape 450 mm internal diameter
1
-
-
Providing and fixing 12mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring
type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in charge (Door handle, lock and stopper etc. to be paid separately)
2.5
-
-
Providing and fixing 15 mm thick false ceiling tiles at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity 0.043 W/m K as per ASTM 518:1991,in true horizontal level on the
existing frame work consisting of T-sections and Lsections suitably fixed according to tile size as per direction of Engineer-in-charge.
10
-
-
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.Group B.
20
-
-
PWiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
100
-
-
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire.
150
-
-
Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required.Group B
50
-
-
Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. 2x1.5 sq. mm.
75
-
-
Supplying and drawing following sizes of FRLS PVC insulated copper conductor single core cable in the existing surface/recessed steel/PVC conduit as required (2x 4.0 sq.mm) -
50
-
-
Supplying and fixing piano type switch on the existing switch box/cover including connections etc. as required 5/6 amps switch
20
-
-
Supplying and fixing piano type switch on the existing switch box/cover including connections etc. as required 15/16 amp switch -
20
-
-
Supplying and fixing piano type socket on the existing switch box/cover including connections etc. as required 3 pin 5/6 amp socket outlet,
60
-
-
Supplying and fixing piano type socket on the existing switch box/cover including connections etc. as required 6 pin 15/16 amp socket outlet
60
-
-
Supplying and fixing piano type Bell Push on the existing switch box/cover including connections etc. as required (DSR.
20
-
-
Supplying and fixing 3 Pin 5 Amps celling rows on the existng junction box/ Wooden block including connection etc. as required.
20
-
-
Supplying and fixing brass batten / angle holder including connection etc. as required.
20
-
-
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way , Double door
4
-
-
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole. (DSR
10
-
-
Supplying and Fixing following rating, double pole, 240 volts, isolator in existing MCB DB complete with connection, testing and commissioning etc as required.40 amps
4
-
-
Providing Wireman service for 8 hour’s service in a day or part as per requirement by experienced electrician with necessary Kit (holding license and T & P) for attending all type of electrical defects as directed by the Engineer-in-Charge.
20
-
-
Providing Carpenter Service for 8 hours service in a day or part as per requirement by experienced Carpenter with necessary T & P for attending minor type of repairing work as directed by the Engineer-In-Charge.
20
-
-
Providing fitter for Plumber service for 8 hours service in a day or part as per requirement by experienced Plumber with necessary Kit for attending minor type of all water supply defects as directed by the Engineer-in-Charge.
25
-
-
Providing beldar service for 8 hours service in a day or part as per requirement to carry out the works as directed by the Engineer-In-Charge.
50
-
-
Supply, installation, testing & commissioning of 1x36 watt fluorescent tube light fitting of Electra slim "Havells" make with requisite accessories like electronic ballast, starter, tube etc. including supply of all materials,labour T&P etc. required for proper completion of work (Based on market rate+DSR -1.41)
25
-
-
Supply, installation, testing & commissioning of ceiling fan "Havells" make ES - 50 premium 5 tar rating model fan sweep 12000 mm, including wiring the down rods of standard length (up to 30 cm with 1.5 sqmm FRLS PVC insulated copper conductor, single core cable, including providing & fixing phenolic laminated sheet cover on the fan box etc as required. (Based on market rate + DSR 1.45)
5
-
-
S/F of Ventilating fan 300 mm dia, Hevell's make "Ventil Air-DB" including supply of all materials, labour T&P etc. required for proper completion of work (Based on market rate+DSR-1.50.1)
10
-
-
Providing and fixing 25 mm thick wood finish aluminium alloy curtain rod with wooden brackets & gulley (weight of curtain rod shall not be less than 240 gm per metre) including all fixtures and labour charges complete.
10
-
-
P/F Havells or equivalent make CFL 23 watt. Including installation, testing and commissioning complete in all respect.
20
-
-
P/F Havells or equivalent make CFL 15 watt. Including installation, testing and commissioning complete in all respect.
40
-
-
providing and fixing pressed steel window frames, manufactured from commercial mild steel sheet of 1.60 mm thickness including hinges,jamb, lock jamb, bead (if required), mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards as specified and applying a coat of approvel steel primer after pre treatment of the surface as directed by engineer-in-charge. modified profile B having single rebate on both side.
45
-
-
P/F of stainless steel Jet spray for European type WC pan including necessary PVC connection complete.
5
-
-
Providing water proofing treatment on roof and wall by Dr. Fixit Pidicrete URP compound of pidilite make cleaning of surface with wire brush. Mixing of Pidicrete URP compound (1 part of compound 1.50 part of cement as per manufacture instruction ) and apply its two coats on leaky surface @ average 0.50 kg/sqm for two coats by skilled labour as per instruction of manufacturer and applying top coat of 12 mm cement plaster 1:4 cement and coarse sand mortar including cost of all material labour T&P etc required proper completion of the work.
50
-
-
Rewinding of burnt exhaust fan with approved copper wire including cost of all material, labour, T&P etc. complete (Burnt wire shall not be taken back)
5
-
-
Supply and Replacing of Damage bearing of ceiling fan. Including cost all T&P and Labour etc. for completion of work.
2
-
-
Taking off the defective ceiling fan from position and rehanging after receiving the repaired fan and proper connection etc.
10
-
-
Suply and replacing of 16 A 240 V. cutout of approved make on board including all material and labour etc. required for proper completion of work.
15
-
-
Suply and replacing of 32 A 240 V. cutout of approved make on board including all material and labour etc. required for proper completion of work.
15
-
-
Supply and replacing of wooden board of 8”x10” size approved quality ,including supply all material, labour and T& P & Polishing etc. required for proper completion of the work complete.
15
-
-
Supply and replacing of wooden board of 4”x7” size approved quality ,including supply all material, labour and T& P & Polishing etc. required for proper completion of the work complete.
7
-
-
Supply and replacing of 15 mm dia tee/socket/ elbow/ bend /nipple etc for repair of pipeline complete. including supply of all material, labour and T& P etc. required for proper completion of the work.
100
-
-
Easing door and Windows including supply of all labour T& P etc. required for proper completion of the work.
50
-
-
Supply and laying chiken mesh of (20mm.) hexgonal heavy quality over roofs of joints as per direction of E/I including supply all material, labour and T& P etc. required for proper completion of the work.
10
-
-
Supply anf Fixing of 22 Gauge aluminium sheet of approved quality including cutting,wastage and fixing the same over wooden door shutters by nails including cost of all material,labour and T&P etc. required for proper completion of work.
20
-
-
Supply and laying of welded mesh (75 mm x 75 mm ) of 10 gauge wire over roofs of joints as per direction of E/I . Including supply of all, Labour , T&P etc. required for proper completion of work
10
-
-
Cleaning of septic tank by removal of Sludge through Sludge Pump attached with tractor /Manually including disposal of waist outside the corporation area as per direction of E/I including cartage, labour and T&P. (capacity 5 cum)
5
-
-
Hiring charges of welding machine for 8 hours. per day. With all labour, T&P and Including welding rod as required for proper completion of work.
10
-
-
Hiring charges of JCB/Crane for 1hours. per day. Including all T&P and labour as required for proper completion of work.
1
-
-
Providing & Fixing CP Brass Pillar Cock of approved quality 15 mm nominal bore (weight not less then 400 grm)
20
-
-
Providing and Fixing Bajaj / Philiphs or equivalent make Regular ballast dichroic reflector 1x40 w Including installation, testing and commissioning complete in all respect.
5
-
-
Providing and Fixing Bajaj / Philiphs or equivalent make 36 w LED including installation, testing and comissioning complete in all respect.
2
-
-
S/F of wall swing fan 300 mm dia, Hevell's make speed 1360 RPM, Pull cord control for speed & oscillation On-Off including supply of all materials, labour T&P etc. required for proper completion of work
2
-
-
Providing and fixing in position wall paper at all heights of approved texture, design and patterns, as per direction of Engineer-in-Charge complete in all respect.
175
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements