Pey Jal Nigam Uttarakhand Tender
View complete overview of Uttarakhand Pey Jal Nigam Uttarakhand Tender
Pey Jal Nigam Uttarakhand Tender
Civil And Construction
Building Construction
Eprocure
Opening Date1 Jul 2024
Closing Date18 Jul 2024
Tender Amount₹ 7,60,55,000
Costs
EMD
₹ 15,21,000Document Cost
₹ 11,800Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_MDPEY_72853_1Bid Award Id
ViewTender No
2469/Nivida(Garh)Khel DDun/95 29/06/24Tender Authority
Pey Jal Nigam Uttarakhand ViewPurchaser Address
-Website
http://http://peyjal.uk.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
DSR item- 2.25a
Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.
130.27
-
-
DSR item- 2.27
Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete.
114.87
-
-
DSR item- 2.35.3.1
Diluting and injecting chemical emulsion (Chlorpyriphos/ Lindane E.C. 20% with 1% concentration), at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surfaces of the excavations made for the foundation of the building, soil under floors, apron, back fill material and along all the faces of the walls for PRE-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II. (Plinth area of Building shall be measured for Payment)
1221.84
-
-
DSR item- 4.1.6
P/L cement concrete - all works upto plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 40 mm nominal size)
70.01
-
-
DSR item- 4.1.8
P/L cement concrete - all works upto plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)
146.12
-
-
DSR item- 4.11
Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).
111.26
-
-
DSR item- 4.13
Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.
111.26
-
-
DSR item- 4.1.3
P/L cement concrete - all works upto plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
7.78
-
-
DSR item- 4.1.10
P/L cement concrete - all works upto plinth level : 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)
6.76
-
-
DSR item- 5.33.1.1
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works upto plinth level. (Note : Cement content considered in M-25 is @ 330 kg/ cum)
426.79
-
-
DSR item- 5.33.2.1
Providing M-25 grade concrete BMC/ RMC. (Note : Cement content considered in M-25 is @ 330 kg/ cum) for columns, pillars piers etc.
418.43
-
-
DSR item- 5.35
Add for using extra cement in the items of design mix over and above the specified cement content therein.
640.17
-
-
DSR item- 5.9
Centering and shuttering including strutting, propping etc. and removal of form for :
-
-
-
DSR item- 5.9.1
DSR item- 4Foundations, footings, bases of columns, etc. for mass concrete
789.7
-
-
DSR item- 5.9.2
Walls (any thickness) including attached pilasters,butteresses, plinth and string courses etc.
85.72
-
-
DSR item- 5.9.6
Columns, Pillars, Piers, Abutments, Posts and Struts
770.06
-
-
DSR item- 5.9.5
Lintels, beams, plinth beams, girders, bressumers and cantilevers.
1562.96
-
-
DSR item- 5.9.3
Suspended floors, roofs, landings, balconies and access platform
1318.19
-
-
DSR item- 5.9.7
Stairs, (excluding landings) except spiral-staircases
104.78
-
-
DSR item- 5.9.19
Weather shade, Chajjas, corbels etc., including edges
213.66
-
-
DSR item- 5.9.20
Suspended floors, roofs, landings, balconies and access platform, with water proof ply 12 mm thick
14.26
-
-
DSR item- 5.22.6
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars
129840
-
-
DSR item- 5.1.2
P/L RCC, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)
11.1
-
-
DSR item- 5.2.2
P/L RCC 1:1½:3 work in suspended floor,roofs, landings, balconies lintel and beams etc.
12.22
-
-
DSR item- 11.4
P/L 52 mm thick C.C. flooring with concrete hardener topping, under layer 40 mm thick C.C. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.
21.97
-
-
DSR item- 6.1.1
Brick work with bricks of Ist class in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand)
19.74
-
-
DSR item- 6.1.2
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)
99.24
-
-
DSR item- 6.4.2
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)
366.69
-
-
DSR item- 6.13.2
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)
369.81
-
-
DSR item- 6.15
Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.
369.81
-
-
DSR item- 9.20.1
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws
203.38
-
-
DSR item- 9.75
Providing and fixing ISI marked Bright finished M.S. fitting for door windows.
-
-
-
DSR item- 9.75.2
250x16x5 mm sliding door bolts
89
-
-
DSR item- 9.74.1
250x10 mm Tower bolt
178
-
-
DSR item- 9.74.3
150x10 mm Tower bolt
444
-
-
DSR item- 9.81.1
125 mm handles
178
-
-
DSR item- 9.81.2
100 mm handles
444
-
-
DSR item- 9.101.2
hanging floor door stopper, Twin rubber stopper
89
-
-
DSR item- 9.68.3
200 Casement stays (straight peg type) with necessary screws etc. complete, weighing not less than 120 gms
444
-
-
DSR item- 9.23
Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).
203.38
-
-
DSR item- 10.2
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
31039.5
-
-
DSR item- 10.14.2.1
Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge: (A) "Profile C" Fixing with adjustable lugs with split end tail to each jamb
623.85
-
-
DSR item- 10.11.1
Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)
7816.5
-
-
DSR item- 9.48.1
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding
6400.35
-
-
DSR item- 9.51.2
Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 12 mm mild steel U beading
426.69
-
-
DSR item- 10.26.1
Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube
863.66
-
-
DSR item- 10.30.2
Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 5.5 mm thick glass panes
426.69
-
-
NSI Item- Providing and fixing f 90mm X20 mm Random length size maple wood flooring by using 2''x3'' size pine wood battern with 10 mm thick cusion pad's on each joint of runner's. The pine wood runners wod be fixed by using fastners and it will be covered by using 12 mm thick water prof ply on top of it. The maple wood will be finish by doing polishing on top.
687.38
-
-
DSR item- 11.41.2
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.
564.94
-
-
DSR item- 11.39
Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete.
187.7
-
-
DSR item- 8.31
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
191.41
-
-
DSR item- 11.56
Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as pecified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
54.08
-
-
DSR item- 11.26.1
Providing and laying 25 mm thick Kota stone flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :
380.87
-
-
DSR item- 11.27.1
Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.
126.98
-
-
DSR item- 12.54.2
Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring ‘T’ with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holesand having NRC of 0.5, electro statically polyester powdercoated of thickness 60 microns (minimum), including factory painted after bending and perforation.
331.35
-
-
DSR item- 12.52.3
Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.
12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.
148.63
-
-
DSR item- 13.1.2
12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)
2717.48
-
-
DSR item- 13.2.2
15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)
1623.24
-
-
DSR item- 13.3.1
20 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)
89.32
-
-
DSR item- 13.7.2
12mm C.P. finished with a floating coat of neat cement in cement mortar 1:4( 1 cement : 4 fine sand)
41.76
-
-
DSR item- 13.16.1
6 mm cement plaster 1:3 (1 cement: 3 fine sand)
923
-
-
DSR item- 13.50.1
Applying priming coat : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)
487
-
-
DSR item- 13.46.1
Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
1836.9
-
-
DSR item- 13.41.1
Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer
3426.82
-
-
DSR item- 13.62.1
Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture
487
-
-
DSR item- 13.8
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
3426.82
-
-
DSR item- 4.17
Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.
135.31
-
-
DSR item- 6.44
Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).
180.42
-
-
DSR item- 22.7.1
Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineerin-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
43.83
-
-
DSR item- 12.21
Providing gola 75x75 mm in cement concrete (1:2:4).
40.64
-
-
DSR item- 22.14.1
Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)
2.41
-
-
DSR item- 22.3
Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.
(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarsesand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.
(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.
(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).
26.37
-
-
DSR item- 22.6
Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying:
(a) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm.(b) laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm.(c) third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30 cm on parapet wall and tucked into groove in parapet all around. (d) fourth and final layer of brick tiling with cement mortar (which will be paid for separately.
15.48
-
-
DSR item- 17.1.1
Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests
5
-
-
DSR item- 17.7.1
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
14
-
-
DSR item- 17.3.1
Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid
14
-
-
DSR item- 17.32.4
Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm
14
-
-
DSR item- 12.41.2
P/L 110 mm dia UPVC soil waste pipe with pressure 6kg/CM2 for sewer.
438.2
-
-
DSR item- 17.73.2
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms
14
-
-
NSI Item-
P/F Upvc nahani trap 110x110mm dia
57
-
-
DSR item- 18.65
Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.
14
-
-
DSR item- 12.43.2
Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.
978
-
-
NSI item-
P/F Upvc terminal guard 110 mm dia
20
-
-
DSR item- 18.74.2
Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length
73
-
-
DSR item- 12.42.5.2
Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110 mm bend
40
-
-
NSI item-
P/F Upvc door bend 110 mm dia.
40
-
-
DSR item- 17.28.2.1
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32 mm dia
26
-
-
DSR item- 12.42.4.2
Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming toIS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 110x110x110 mm tee
100
-
-
DSR item- 17.8
P/F white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.
8
-
-
DSR item- 17.5.2
Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern
6
-
-
DSR item- 8.10.2
Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade
5.62
-
-
DSR item- 12.41.2
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter
942
-
-
DSR item- 12.42.1
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.
-
-
-
DSR item- 12.42.5.2
110 mm bend
92
-
-
DSR item- 12.42.6.2
110 mm Shoe
92
-
-
DSR item- 12.42.4.2
110x110x110 mm tee
84
-
-
DSR item- 12.22
Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete (1:2:4).
92
-
-
DSR item- 12.43.2
Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.
110 mm
1656
-
-
DSR item- 18.11.1
Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore
200.2
-
-
DSR item- 18.1
Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.
-
-
-
DSR item- 18.10.2
20 mm dia nominal bore
1245
-
-
DSR item- 18.10.3
25 mm dia nominal bore
516
-
-
DSR item- 18.12.4
Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 32 mm dia nominal bore
660
-
-
DSR item- 18.49.1
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore
19
-
-
DSR item- 18.52.1
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore
2
-
-
DSR item- 18.17
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
-
-
-
DSR item- 18.17.1A
20mm nominal bore
60
-
-
DSR item- 18.17.1
25 mm nominal bore
24
-
-
DSR item- 18.17.2
32 mm nominal bore
8
-
-
DSR item- 18.58.1.1
Providing and fixing PTMT grating of approved quality and colour. 100 mm nominal dia
57
-
-
DSR item- 18.48
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
64000
-
-
DSR item- 18.18.2
Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore
16
-
-
DSR item- 18.20.3
Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 25 mm nominal bore
16
-
-
DSR item- 18.51.1
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore
38
-
-
DSR item- 18.53.1
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore
73
-
-
DSR item- 18.64
Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms
2
-
-
DSR item- 19.19.1
P/F in position pre cast RCC manhole cover and frame of required shape and of approved quality. Rectangular shape 600x450mm internal dimensions
4
-
-
DSR item- 19.15.1
Providing MS foot rest including fixing in manholes with 20x20x10cm cement concrete blocks 1:3:6 as per standard design. (i) with 20x20mm square bar
64
-
-
DSR item- 19.19.4.1
P/F in position pre cast RCC manhole cover and frame of required shape and of approved quality. EHD - 35 : Circular shape 560 mm internal dia
3
-
-
DSR item- 23.1.1.1
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia
70
-
-
DSR item- 23.5
Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge
4.57
-
-
DSR item- 23.6
Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge
4.57
-
-
DSR item- 23.7
Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.
4.27
-
-
DSR item- 23.8
Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineerin- charge.
3.71
-
-
DSR item- 23.3.2
Supplying, assembling, lowering and fixing in vertical position in bore well,unplasticized PVC medium well casing (CM) pipe of required dia,conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia
36
-
-
DSR item- 23.4.2
Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia
34
-
-
DSR item- 23.13.2
Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 150 mm dia.
1
-
-
DSR item- 23.14.2
Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts f required size complete. 150 mm clamp
1
-
-
DSR item- 23.15.2
Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I): 150 mm dia.
1
-
-
DSR item- 19.6.2
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe
135
-
-
DSR item- 19.32.1
Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.
1
-
-
NSI Item-
Acoustical Ceiling : Providing & fixing perforated Gypsum false ceiling , as marked in the drawings, consisting of GI perimeter channels of size 0.55mm thick (having one flange of 20mm and another flange of 30mm and a web of 27mm) along with perimeter of ceiling, screw fixed to brick wall/ partition with the help of nylon sleeves and screws, at 610mm c/c. Then suspending GI intermediate channels of size 45mm (0.9mm thick with 2 flanges of 15mm each) from the soffit at 1220mm c/c with ceiling angles of width 25mm x 10mm x 0.55mm thick fixed to soffit with GI cleats and steel expansion fasteners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in a direction perpendicular to the intermediate channel at 300mm c/c. Finished in 12.5mm thick micro-perforated gypsum board, 1200mm x 2400mm, with 3mm dia square perforations. The board shall have an overlay of 50mm thick, 1000 GSM polyester wadding, appropriately covered with FGT tissue (in the case of glasswool/ rockwool). The ceiling to be finished with 2 or more coats of mat type plastic emulsion paint after proper jointing & making surface smooth. Approved make of gypsum perforated board: Knauf Danoline/ Absound Overseas micro perforated/ Saint gobin -Quattro board.
295.93
-
-
NSI Item-
Acoustical paneling on walls : Providing and fixing Acoustical Wall paneling with Compressed polyester fibre nonwoven 10mm thick panels with a density of 200kg/m3, of size1200mmX600mm with an NRC of 0.80 to 0.85 . The panels to be pasted with approved construction adhesives over 9mm thick perforated ply (minimum 20% perforations). The 9mm thick perforated ply shall be fixed over GI framing consisting of 48x36x34x0.5mm thick GI Studs wall channels & floor channels @ 600mm c/c with filling of 50mm thick 1000GSM thermally bonded polyester wadding. The insulation to be supported from the back by covering the frame with 19mm mesh GI wire netting. Approved Make : Acoustic India/ Absound Overseas/AMF.
1608.31
-
-
NSI Item-
Providing & fixing 100x15mm thick Polished teak wood skirting at the bottom of wall paneling. The skirting shall be fixed over 12mm thick commercial ply to match the level of paneling.
78.8
-
-
NSI Item-
Providing and fixing 90x20mm thick, in random length, Maple wood planks flooring with tongue & groove joints ,fixed to pine wood joist of size 72 x 48 mm at 230-300 mm c/c in one direction , pine wood joists to be resiliently supported on 75x50 mm rubber pads. The cavity of framing shall be filled with 50mm thick rock wool insulation of density 48kg/cum. Polishing of flooring on exposed surface: In horizontal/vertical plane (Rate for flooring shall include providing additional framework required for housing microphone and power outlet junction boxes.
295.93
-
-
NSI Item-
Entry/exit doors 77mm thick, acoustic doors consisting of fire resistant materials & peripheral seals all around . The door to be laminated with 1mm thick laminate. The Door shutter frames to be of klin dried chemically treated second class teak wood. The door shutter frame to be lapped with 12mm thick BWR ply duly treated for fire retardance. Make : Global Fire/ Navair/ Absound Overseas.
4.32
-
-
NSI Item-
Chowkhats for the doors in second class teak wood of size 125x 75mm duly fire treated.
8.4
-
-
NSI Item-
Providing and fixing panic bars for the doors with double/single leaf with all necessary parts. Make: Geze/Dorma/Doorwin
1
-
-
NSI Item-
Providing and fixing Hinges (Steel with bal bearings ) of size 125 X 32mm fixed with steel drive all screws of 35mm. Make: Doors, Ozone, Dorma
6
-
-
NSI Item-
Providing and fixing external trim with locking arrangement & handle for panic bars double/single leaf with all necessary parts. Make: Geze/Dorma/Doorwin
2
-
-
NSI Item-
Providing and fixing heavy duty door closers of load capacity of 100-120kg with all necessary parts. Make: Doors/Dorma/Godrej
2
-
-
DSR Item-2.1
Trenching in ordinary soil up to a depth of 60cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling with in a lead of 50m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).
94.82
-
-
DSR Item-2.2
Supplying and stacking of good earth at site i/c royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).
63.22
-
-
DSR Item-2.3
Supplying and stacking sludge at site including royalty and carriage up to 1 km (sludge measured in stacks will be reduced by 8% for payment)
15.8
-
-
DSR Item-2.4.1
Supplying and stacking at site dump manure from approved source, including carriage up to 1 km (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm
15.8
-
-
DSR Item-2.5
Rough dressing the trenched ground including breaking clods
158.04
-
-
DSR Item-2.6
uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation
158.04
-
-
DSR Item-2.7
Fine dressing the ground
158.04
-
-
DSR Item-2.8
Spreading of sludge, dump manure or/and good earth in required thickness (Cost of sludge, dump manure or/ and good earth to be paid separately)
79.02
-
-
DSR Item-2.9
Mixing earth and sludge or manure in proportion specified or directed by the officer-in-charge
79.02
-
-
DSR Item-2.10.1
Grassing with selection no. 1 grass including watering and maintenance of the lawn for 60 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including Supplying good earth, if needed (the grass and earth shall be paid separately). In rows 5 cm apart in both directions.
158.04
-
-
DSR Item-2.12
Uprooting rank vegetation and weeds by digging the area to a depth of 60cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts
158.04
-
-
DSR Item-2.13
Preparation of beds for hedging and shrubbery by excavating 60cm deep and trenching the excavated base to a further depth of 30cm refilling the excvated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of rearth after redution by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling and directed, within a lead of 50m. lift upto 1.5m complete (cost of sludge, manure or extra earth to be paid for seperately)
3.6
-
-
DSR Item-2.14.4
Digging holes in ordinary soil and refilling the same with the exavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reductin by 8%9 flooding with water, dressing including remocal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for seperately) Holes 45cm dia and 45cm deep
2
-
-
DSR Item-2.16
Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge.
2
-
-
DSR Item-2.19.1
Edging with bricks laid dry length wise, including required excavation, refilling, consolidating with hand packing and spreading surplus earth neatly within a lead of 50 m : Common burnt clay F.P.S. (non modular) bricks of class designation 7.5
40
-
-
DSR Item-2.28
Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge
180
-
-
DSR Item-2.35
Supplying and stacking of Selection No.-1 Grass at site fresh and free from weeds having proper roots in green including loading, unloading, carriage and all taxes paid etc. and as per direction of officer in charge.
158.04
-
-
DSR Item-2.54
Anti termite treatment by digging holes 30 cm deep and 4 cm dia, 6 to 7 holes around the tree using chemical emulsion at the rate of 1.5 liter per hole in two time or more application to get the trees free from termite infection chemicals used Chlorpyriphos 20% EC in the ratio of 1% concentration and as per direction of officer-in-charge
2
-
-
DSR Item-2.57
Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cost of plant & water)
-
-
-
DSR Item-2.57.1
Trees Plant
2
-
-
DSR Item-2.57.2
Shrubs Plant
100
-
-
DSR Item-5.13
Providing and Displaying Cycus cirsnallis well developed with fresh & healthy 35 to 40 lush green leaves in 40 cm Cement Pot as per direction of the officer-in-charge.
2
-
-
DSR Item-8.1
Providing and stacking of Cassia biflora of height 90-105 cm., well branched, bushy in big size HDPE bag as per direction of the officer-in-charge.
100
-
-
DSR Item-18.12
Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.
-
-
-
DSR Item-18.12.2
20 mm dia
125
-
-
DSR Item-18.12.3
25 mm dia
75
-
-
DSR Item-18.12.4
32 mm dia
30
-
-
DSR Item-18.17.1
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):
-
-
-
DSR Item-18.17.1A
20 mm dia
8
-
-
DSR Item-18.17.1
25 mm dia
8
-
-
DSR Item-18.17.2
32 mm dia
2
-
-
DSR Item-18.20.2
Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 20 mm nominal bore
8
-
-
DSR Item-18.20.3
Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main :25 mm nominal bore
8
-
-
DSR Item-18.32.1
Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
8
-
-
DSR Item-18.33.1
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation oncrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5
10
-
-
DSR Item-18.40
Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :
-
-
-
DSR Item-18.40.2
20 mm diameter pipe
125
-
-
DSR Item-18.40.3
25 mm diameter pipe
75
-
-
DSR Item-18.40.4
32 mm diameter pipe
30
-
-
DSR Item-18.41
Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work :
-
-
-
DSR Item-18.41.2
20 mm diameter pipe
125
-
-
DSR Item-18.41.3
25 mm diameter pipe
75
-
-
DSR Item-18.41.4
32 mm diameter pipe
30
-
-
DSR Item-18.46
Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :
-
-
-
DSR Item-18.46.2
20 mm diameter pipe
8
-
-
DSR Item-18.46.3
25 mm diameter pipe
8
-
-
DSR Item-18.46.4
32 mm diameter pipe
2
-
-
DSR Item-2.13.1.2
Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material rmeasurements and disposal of nserviceable material as directed, within a lead of 50 m :Ordinary rock : Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia
50
-
-
DSR Item-19.3.2
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :
150 mm dia. R.C.C. pipe
50
-
-
DSR Item-19.4.1.2
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 100x100 mm size P type With Sewer bricks conforming to IS : 4885
15
-
-
DSR Item-19.7.1.2
Constructing brick masonry M.H. in C.M. 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with C.M. 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in C.C. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90X80X45 cm i/c C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With Sewer bricks conforming to IS : 4885
3
-
-
DSR Item-19.8.1.2
Extra for depth for manholes : Size 90x80 cm- With Sewer bricks conforming to IS : 4885
0.45
-
-
NSI Item- Supply & installation of 28 mm WPC Jali of size 7'x3' Complete with Scafolding & Fixing as per approved Design.
42
-
-
DSR Item- 4.2
Supplying, installation, testing and commissioning of electric driven terrace pump with DOL starter suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainlesssteel shaft, mechanical confirming to IS : 1520Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation,conforming to IS-325 .M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as requiredSuitable cement concrete foundation duly plastered and with anti vibration pads.
450 lpm at 35 m Head
2
-
-
DSR Item-7
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including,Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the
wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthatic enamel paint of required shade complete as required :
-
-
-
DSR Item-7.1
25 mm dia
50
-
-
DSR Item-7.2
32 mm dia
20
-
-
DSR Item-7.3
40 mm dia
100
-
-
DSR Item-7.4
50 mm dia
100
-
-
DSR Item-7.5
65 mm dia
200
-
-
DSR Item-7.6
80 mm dia
40
-
-
DSR Item-7.7
100 mm dia
200
-
-
DSR Item-9.2
Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :
Single headed Stainless steel
8
-
-
DSR Item-10.2
Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank
Gunmetal/Stainless Steel cap and chain as required :
Single headed Stainless steel
2
-
-
DSR Item-11
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gasketsconforming to IS 13095 of following sizes as required :
-
-
-
DSR Item-11.1
40mm
6
-
-
DSR Item-11.2
50mm
6
-
-
DSR Item-11.3
65mm
9
-
-
DSR Item-11.5
100mm
4
-
-
DSR Item-12.5
Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required
100mm
4
-
-
DSR Item-13
Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.
10
-
-
DSR Item-14.5
Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required
100mm
4
-
-
DSR Item-16.2
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required
Stainless Steel (Grade 304)
20
-
-
DSR Item-17.1
Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.
30 mtrs
12
-
-
DSR Item-18.2
Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required
Stainless Steel (Grade 304)
10
-
-
DSR Item-19.1
Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required. 2 way-100 mm dia M.S. Pipe
2
-
-
DSR Item-20
Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade
as required.
2
-
-
DSR Item-22
Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.
6
-
-
DSR Item-18.48
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
30000
-
-
DSR Item-17.2.14
Supplying, installation, testing & commissioning of addressable manual call point complete as required.
20
-
-
DSR Item-17.2.6
Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required.
20
-
-
DSR Item-21
Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :
-
-
-
DSR Item-21.1
Pendent Sprinkler
80
-
-
DSR Item-21.2
Upright Sprinkler
40
-
-
DSR Item-21.3
Horizontal Side wall
20
-
-
DSR Item-23.1
Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.
100mm
4
-
-
DSR Item-24.2
Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/ sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasketetc of follwing sizes as required :
100 mm
2
-
-
DSR Item-25
Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.
-
-
-
DSR Item-25.1
700mm
30
-
-
DSR Item-25.2
1000mm
10
-
-
DSR Item-25.3
1200mm
20
-
-
DSR Item-29
Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required
80
-
-
NSI Item-
Providing and fixing Carbon-di-oxide Fire Extinguishers consisting of welded M.S cylindrical body, squeeze lever discharge valve fitted with internal discharge tube. 30cms long high pressure discharge hose. Discharge nozzle,suspension bracket, confirming to IS:934 finished externally with red enamel paint and fixed to wall with brackets with rawl plug/dash fasteners complete with internal charge. (CCOE Nagpur Approved clynders)
Capacity 4.5 Kg.
8
-
-
NSI Item-
Providing and fixing of ABC type (Stored Pressure) Fire Extinguisher I.S.I marked & T.A.C.approved complete in all respect.4 kg. capacity
16
-
-
NSI Item-
Providing and fixing Mechanical foam ( AFFF) Fire Extinguisher I.S.I marked & T.A.C.approved complete in all respect. Capacity 9 Ltr.
3
-
-
NSI item-
Providing and Fixing of self illuminated /auto glow Exit signs printed on photoluminescent sheet containing self illuminated base chemical,of appropriate size not less than 400x150mm,suspended from ceilling or fixed to the walls with accessories as riquired and as directed at site.
12
-
-
NSI item-
Supplying and installing 4 MP IP CCTV Bullet camera,CP Plus.
8
-
-
NSI item-
Supplying and installing 4 MP IP CCTV Dome camera,CP Plus.
20
-
-
NSI item-
POE Acess Switch 24 Port
2
-
-
NSI item-
D-Link 6U Rack Enclosures Networking/Server Rack with cable management and Connectors etc. as reqd. D-LinkR (NWR-6U-5045-GR)
2
-
-
NSI item-
64 Input and 4 Output Channel Video Recorder For Cctv SystemSparshR
(SR-NP3232F5H-H(E)(D)(P))
2
-
-
NSI item-
Sony 82 cms LCD Panel monitor.
2
-
-
NSI item-
FES 8 Ports Managed PoE+ Layer 2 Access Switch FESR (FES-GS-1010P)
2
-
-
DSR item- 1.21
-Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
-
-
-
DSR item- 1.21.1
20 mm
100
-
-
DSR item- 1.21.2
25 mm
100
-
-
DSR item- 1.53.2
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 2 cable run
400
-
-
NSI item-
Providing GODREJ INTERIO 5 Seater Sofa with fabric cover. (5116877-59651231270)
2
-
-
NSI item-
Providing GODREJ INTERIO 3 Seater Sofa With Leatherite Cover. (5116877-34457755522)
1
-
-
NSI item-
Providing ROSE DESIGNER CHAIRS Non-Revolving and Non-Tilting chair with Armrest (5116877-43387308161)
2
-
-
NSI item-
Providing GODREJ INTERIO Wooden Double Bed Storage Box Opening from Side (5116877-5886908047)
3
-
-
NSI item-
Providing Commercial Board Bed Side Table. Delight or Equivalent Make. Gem id- 5116877-80473624822.
3
-
-
NSI item-
Providing Sony Smart Television Tv 43 Inch Smart TV (Android TV) (5116877-50936388003)
2
-
-
NSI item-
Providing LG 280 L 2 Star Frost Free Double Door Refrigerator (5116877-77358491272)
1
-
-
NSI item-
Providing Kurlon Spring Mattress (5116877-43544256862)
3
-
-
NSI item-
Providing Powder Coated MS 4 Seater Table. Gem id- 5116877-99918969308.
1
-
-
DSR item- 1.10.3
Wiring for light point/ fan ponit/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, with modular switch, modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group-C
316
-
-
DSR item- 1.12
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed mediumclass PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
2100
-
-
DSR item- 1.13
Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
1200
-
-
DSR item- 1.4
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.
-
-
-
DSR item- 1.14.1
2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
610
-
-
DSR item- 1.14.2
2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
2212
-
-
DSR item- 1.14.4
2 X 6 sq. mm + 1 X 6 sq. mm earth wire
600
-
-
DSR item- 1.14.10
4 X 10 sq. mm + 2 X 6 sq. mm earth wire
240
-
-
DSR item- 1.18.2
Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair
855
-
-
DSR item- 1.19
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
360
-
-
DSR item- 1.11
Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
4
-
-
DSR item- 1.21
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
-
-
-
DSR item- 1.21.1
20 mm
1350
-
-
DSR item- 1.21.2
25 mm
330
-
-
DSR item- 1.32
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
60
-
-
DSR item- 1.31
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
61
-
-
DSR item- 1.38
Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.
4
-
-
DSR item- 2.5.1
Supplying and fixing of following ways surface/ recess mounting, Vartical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. 4Way (4+12), Double door
2
-
-
DSR item- 2.4.2
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6way 4+18 Double Door
3
-
-
DSR item- 2.5.2
Supplying and fixing of following ways surface/ recess mounting, Vartical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as required. 8Way (4+24), Double door
2
-
-
DSR item- 2.4.2
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6way 8+18 Double Door
3
-
-
DSR item- 2.10
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
Single pole and neutral
-
-
-
DSR item- 2.10.1
Single pole
132
-
-
DSR item- 2.10.5
Triple pole and neutral
10
-
-
DSR item- 5.4
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.
4
-
-
DSR item- 5.9
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut
bolt & spring washer spaced at 50mm)
140
-
-
DSR item- 1.25
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
24
-
-
DSR item- 10.18
P/F Circular/HexagonalCast Iron or M.S sheet box for ceiling fan clamp of internall dia 140mm, 73mm height top lid of 1.5mm thick MS sheet with its top surface hacked for proper bonding, top lid shell be screwed into the cast iron/ M.S sheet box by meansof 3.3mm dia round headed screws, one lock at the corners. clamp shall be made of 12mm dia M.S. bar bent to shape as per standard design.
24
-
-
DSR item- 1.33
Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.
43
-
-
DSR item- 1.24
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
-
-
-
DSR item- 1.24.6
Telephone socket outlet
19
-
-
DSR item- 1.24.7
TV antenna socket outlet
8
-
-
DSR item- 1.27.2
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 3 module
27
-
-
DSR item- 1.40
Providing and fixing plain 16/0.20mm (0.50sqmm) twin circular flexible FRLS PVC insulated, PVC sheathed copper conductor cable direct on the wall with PVC clips etc. as required.
300
-
-
NSI item-
Heigh Bay LED Light 100 W Ceiling mounting type Acentech AB_HB_100
48
-
-
NSI item-
36/40 W LED Batten tube Surya 40W6500K LED
35
-
-
NSI Item-
300mm Bajaj propeller type ventlating fan with bird screen Freshee 300mm
21
-
-
DSR item- 19.1
Supply, Installation, Testing and Commissioning of 1200 mm sweep,BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.
24
-
-
NSI item-
LED 12 W Recess mounting Down Lighter Phillips DN296B
90
-
-
NSI Item-
36W 2x2 LED panel Crompton CGCEL Panel luminary
76
-
-
DSR item- 1.41
Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.
82
-
-
DSR item- 1.50.1
Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.
21
-
-
NSI item-
Providing Gyser (water Heater) 15 Liter Capacity. 5 Star Candes
11
-
-
DSR item- 2.11
S/F single pole blanking plate in the existing MCB DB complete etc. as required. (4 no. /MCBDB)
20
-
-
DSR item- 1.57
Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required. For AC
15
-
-
NSI item-
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate One Module for modular switches in recessincluding supplying and fixing Cat-6 Data Information Outlet, crimpling, connection, testing etc. as required.
19
-
-
DSR item- 1.53.2
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 2 cable run
950
-
-
NSI item-
Supplying installation testing commissioning of 24 Port, Gigabit Data switch Dlink with 2 U rack , cable maneger etc as reqd.
4
-
-
NSI item-
10W LED Batten Wipro Garnet D631065 Polycarbonate 6500K
18
-
-
DSR item- 2.3.2
Supplying and fixing 8 way, Double Door single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
4
-
-
DSR item- 6.2
Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
4
-
-
DSR item- 6.7
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)
600
-
-
DSR item- 6.8
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run
100
-
-
DSR item- 6.12
Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I.bolts, nuts, chuck nuts and spring washers etc. complete as required.
4
-
-
DSR item- 6.14
Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.
100
-
-
NSI Item-
Terminal equipment at consumer end including HT cables, CT PT , meter cubicle etc. 1 sets
For independent feeder terminal equipment at sending end including swithch gear, ht cables, ct pt, meter cubicle etc 1 sets.Over Head 11 KV Line Cost. Security Deposit for Rs. 1000/KW for 120KW
1
-
-
DSR Item- 6.2.1
Supplying,installation,testing and commisioning of 400 Kva 11kV/0.433 kV outdoor Package type compact substation equipments comprising HT Panel, Dry type Transformers, HT cable, Bus trunking from Transformer to LT Panel, LT Panel, Automatic Power factor correction panel, Active Harmonic Filters,TVSS (Transient Voltage suppression system), SPD (Surge protection system), Essential panel,Earthing,required inter-connections, substation safety euipments including LT cabling from sub station to the buildings fed by the sub station.
250
-
-
NSI item-
S/F XLPE insulated screened PVC beded galvanized steel strip of wire armoured electric power cable (heavy duty) with aluminium conductor 11KV greds cross sectional area 35 sqmm as per diected by engineer-in-charge. For metering eqpt.
80
-
-
DSR item- 5.4
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
12
-
-
DSR item- 5.11
Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe FRLSom earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.
320
-
-
DSR item- 5.6
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.
6
-
-
DSR item- 5.10
Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.
60
-
-
DSR item- 9.1
Supplying and making end temination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed /XLPE aluminium couductor cable of 1.1 KV grade as required.
-
-
-
DSR item- 9.1.1
2x6
20
-
-
DSR item- 9.1.33
4x16
12
-
-
DSR item- 9.1.21
3.5x35
10
-
-
DSR item- 9.1.23
3.5x70
4
-
-
DSR item- 10.5.2
S/M OUTDOOR cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required: upto 35 sq. mm
1
-
-
DSR item- 10.4.2
supplying and making indoor cable end termination with heatshrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core,35 sq.mm, XLPE aluminiumconductor cable of 11 KV grade as required :
5
-
-
DSR item- 13.13
S/E of three piece nonlinear resistor type lighting arrestor suitable for 3 wire, 11 KV overhead lines with rated voltage 9 KV (rms) with a nominal discharege current rating of 5 KV and complete with galvanised clamping arrangenment, G.I. bolts, nuts, washers etc. as required.
2
-
-
NSI Item-
6 meter GI octegonal pole single arm with loop in box Bajaj
12
-
-
NSI item-
Erection of Octagonal street light pole of 6 to 8 meter length in RCC 1:2:4 foundation including excavation, refilling, Reinforcement etc. as per Pole Manufacture design.
8
-
-
NSI item-
Supplying and fixing 60W LED streetlight made up of pressure die cast housing with toughned glass and individual LEDs with secondary optics and IP66 protection complete with all accessaries.
8
-
-
NSI item-
Supplying and Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade aluminium conductor armored of following size in the existing
RCC/ HUME/ METAL pipe as required.
-
-
-
NSI item-
2x6 sq.mm
125
-
-
NSI item-
4X16 Sq.mm.
100
-
-
NSI item-
3.5x35 Sqmm
100
-
-
NSI item-
3.5x70 Sqmm
50
-
-
DSR Item- 14.13
Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required
-
-
-
DSR Item- 14.13.3
100mm
20
-
-
DSR Item- 14.13.4
150mm
40
-
-
DSR Item- 14.14.4
Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 300mm
18
-
-
DSR Item- 3.1.1
Supply ,installation testing and commissioning of 8 Pessenger (544Kg.)Machine Room less lift having contract speed of 1.0 meter per second serving four different floors (G+2) 3 floors , Type(MRL) Machine room less with gearless traction having + /- 5% landing accuracy,,speed 1.0 mps,4 levels with a total travell of 15 mtrs,(approx.) with 5 stops, opening all on one side,with VAVF cotroller,having ARD with Dry MF batterirs, Microprocessor based simples slective collective with attendent operations,415 V 50 Hz 3 phase 4 wire power,with power operated centre opening horizontal sliding stainless steel scrach free car and landing doors, Car size and dimenssions suitable for hospital strchers,, infra red curtain and one hour fire rating,,with overload waring indiactor,, concealed luminary with LED light, axial pressure ceiling fan, shaft size 2.0x2.07 mtrs. with voice annoucement system. etc as required.
1
-
-
DSR Item- 6.3.1
Supplying, installation, testing and commissioning of silent DG sets, AMF panel, Bus Ducting/cables from DG sets to Essential panel, synchronizing panel where required, DG set enclosure room sound insulation/ ventilation/smoke exhaust as required, earthing of dg set system, control cabling, fuel tank/piping, dg set exhaust piping/exhaust chimney as per CPCB Norms, Civil works connected with dg sets including foundation as required.
62.5
-
-
NSI item-
Supply installation testing and commissioning of Carrier 1.5 Ton 3 Star High wall Split AC (Hot and Cold) CarrierR (Carrier & Superia 365) including initial charging etc. as reqqd.
15
-
-
NSI item-
SITC of OutDoor Type, Double Door Feeder Pillar with minimum 2mm thick MS sheet 7 Tank treatment powder coated Painted with Sloping Canopy suitable size of TPN Aluminium Bus Bar, Earth Bar,Pad locking arrangement, LED Indication Lights, Detachable Gland Plate, fixed on CC Foundation with making suitable CC foundation capable to accomodate the following MCCBs, Interconnection etc. as reqd.
200 A,36KA,FPMCCB - 1 no
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements