Kumaon Mandal Vikas Nigam Limited Tender

Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). All works upto plinth level.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level-

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and laying in position specified grade of reinforceed cement cocrete excluding the cost of centering, shuttring, finishing and reinforcment - All work upto plinth 1:1.5:3 (1 Cement : 1.5 Coarse sand : 3 Graded stone aggregate 20mm nominal size)level for plinth beam

Reinforced cement concrete work in walls (any thickness),including attached pilasters, buttresses, plinth and string courses,fillets, columns, pillars, piers,abutments, posts and struts etc. upto floor five level excluding cost of centring,shuttering, finishing and reinforcement.1:1.5:3 (1 Cement : 1.5 Coarse sand : 3 Graded stone aggregate 20mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multichambered frame, sash and mullion (where ever required) xtruded profiles duly reinforced with 1.60 ± 0.2 mm thickgalvanized mild steel section made from roll forming process ofrequired length (shape & size according to uPVC profile), uPVCextruded glazing beads of appropriate dimension, EPDM gasket,stainless steel (SS 304 grade) friction hinges, zinc alloy (whitepowder coated) casement handles, G.I fasteners 100 x 8 mm sizefor fixing frame to finished wall, plastic packers, plastic caps andnecessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately)Casement window double panels with top fixed with S.S. friction hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mmand single glazing bead of appropriate dimension.(Area of window upto 2.50 sqm).

Providing and fixing factory made 30 mm thick door shutter made ofsolid PVC foam profile. The styles & rails shall be of size 75 mm x 30mm having wall thickness 5 mm. The styles, top & bottom rails shallhave one side wall thickness of 15 mm tegrally extruded on the hingeside of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mmx 1 mm,painted with primer , all four corners of reinforcement to be welded orsealed. Solid PVC extruded bidding (push fit type) will be set inside thestyles and the rails with a cavity, to receive single piece extruded 5 mmPVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws.Single piece extruded solid PVC lock rail of size 100 mm x 30 mm withwall thickness 5 mm & 15 mm integrally extruded in the middle of thelock rail & fixed with styles with the help of PVC solvent cement & selfdriven self tapping screws of size 100 mm x 8 mm complete as ermanufacturer's specifications and direction of Engineer-in-charge.Decorative finish (both side wood grained finish)

Providing and fixing factory made 30 mm thick door shutter made ofsolid PVC foam profile. The styles & rails shall be of size 75 mm x 30mm having wall thickness 5 mm. The styles, top & bottom rails shallhave one side wall thickness of 15 mm integrally extruded on the hingeside of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mmx 1 mm,painted with primer , all four corners of reinforcement to be welded orsealed. Solid PVC extruded bidding (push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5 mmPVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screwsSingle piece extruded solid PVC lock rail of size 100 mm x 30 mm withwall thickness 5 mm & 15 mm integrally extruded in the middle of thelock rail & fixed with styles with the help of PVC solvent cement & selfdriven self tapping screws of size 100 mm x 8 mm complete as per manufacturer's specifications and direction of Engineer-in-charge.Decorative finish (both side wood grained finish)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water tinnable priming coat with cement primer

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)

Providing and fixing precoated galvanised iron profile sheets (size,shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete:12.51.1 Ridges plain (500 - 600mm)

Barge board (Upto 300 mm)

Gutter (600 mm over all girth)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means Excavation in all kinds of soil.

Providing and laying in position cement concrete 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size).

Providing and laying in position cement concrete 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Filling of excaveted earth in plinth ,sides,road,foundation etc.20cm in depth, laid up 50 cm, lift up 1.5 meter.

Dry stone pitching/masonry 22.5 cm thick including supply of stones and preparing surface complete.

R.C.R Stone massonary laid 1:6 cement sand mortar.

Providing wood work in frames of Hand rail,and other frame work using other Sal wood.

Providing and fixing Panneled & Glazed shutters for doors, windows and clerestory windows Second class shisum wood 30 mm thick.

12 mm cement plaster of mix 1:4 (1 cement : 4 fine sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface.

Painting with synthetic enamel paint of approved brand and manufacture of required Two or more coats on new work over an under coat of suitable shade with ordinary

Supply and fixing vitrified tiles in flooring or in skirting or dado laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry, jointing and plashing complete including supply of all material, labour and t&p etc complete. 600x600mm

52 c.m thick 1:2:4 plain cement concrete floor with cement ,approved course sand& 20mmgraded approved stone ballast laid in panels finish with 3mm floating coat of neat cement or cement & marble dust in 5:1 as specified including 8 cm thick base concrete in proportion of 1:5:10 and removing any over lapping mortar at the joint of panels and giving them a uniform finish including supply of all material,labour,T&P etc required for proper completion of work.

Providing and fixing glass strips in joints of terrazo/ cement concrete 40 mm wide and 4 mm thick

15 mm dia G.I pipe

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works,including applying priming coat of approved steel primer.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. All kind of soil.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block makingmachine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete

Random rubble masonry with hard stone in foundation and plinth includinglevelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12graded stone aggregate 20 mm nominal size) upto plinth level with :Cement mortar 1:6 (1 cement : 6 coarse sand)

Random rubble masonry with hard stone in superstructure above plinth level and upto floor five level, including leveling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) at window sills, ceiling level and the like.

Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) :Red sand stone - Exposed face fine dressed with rough

4.0 cm thick cement conrete flooring 1:2:4 cement coarse sand and 20 mm aggregate finished with a floting cost of neat cement including cement sullary but excluding the cost of nosing of teps etc.

M.S. iron work in heavy size and section such as truss etc. built up gates etc. including S/o all materials, labor and T&P etc. for proper completion of work. SI no 503 P.

Constructing massonry chamber 60x45x50 cm, inside with 75 class brick work in cment mortar

Providing and fixing on wall face unplasticised PVC moulded fittings/accessories for unplasticised Rigid PVC rain water to IS: 13592 Type A, including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion Single tee with door

Brick work 7 cm thick with common burnt clay F.P.S. (non modular) brick of class designation 7.5 in cement mortar 1:3 (1 cement : 3coarse sand) in superstructure above plinth level and upto floor five

Making soad pit 2.5 m diameter 3.0 metre deep with 45x45 cm dry brick money with P.PS. Bricks

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L'hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporatingminimum 0.3% ultra-violet stabiliser in resin system underapproximately 2400 psi and hot cured. They shall be of uniformpigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.