Bridge Ropeway Tunnel And Other Infrastructure Development Corporation Of Uttarakhand Limited Tender
View potential partner for Uttarakhand BRIDCUL Tender
Bridge Ropeway Tunnel And Other Infrastructure Development Corporation Of Uttarakhand Limited - BRIDCUL Tender
Electrical and Electronics
Electrical Works
Eprocure
Opening Date22 Feb 2025
Closing Date3 Mar 2025
Tender Amount₹ 3,44,79,000
Technical
Technical
Financial
Class Of Bidder
... View More
The class eligibility requirement to bid or participate in this tender is Class "A" Electrical License, however it is also mentioned that the specific class eligibility requirement is not explicitly stated. But since Class "A" is mentioned, it can be considered as the class eligibility requirement.
Bid Capacity
... View More
The bid capacity required in the given tender to bid can be calculated using the formula: Assessed Available Bid Capacity = (A*N*2-B) Where:
A = Maximum value of Electrical engineering works executed in any one year during the last five years (updated to the price level of the year indicated in Appendix)
N = Number of years prescribed for completion of the works for which bids are invited
B = Value (updated to the price level of the year indicated in Appendix) of existing commitments and on-going works to be completed during the next one) Alternatively, the bid capacity required is mentioned as 20% of the estimated cost, which is Rs 68.96 Lac. Additionally, the bidder should have experience of similar works worth at least 25% each of the tender value, i.e., Rs 86.20 Lac, in the last five years, with an escalation factor applied to the experience value based on the year of completion. The escalation factors for indexing the value of experience are:
- 2019-2020: 1.46
- 2020-2021: 1.33
- 2021-2022: 1.21
- 2022-2023: 1.10
- 2023-2024: 1.00 Experience Value = (Cost of Project) x (Escalation Factor)
Technical Capacity
... View More
The required prior work experience for the bidder includes having completed at least one similar work worth 35% of the tender value, which is Rs. 120.68 Lac, or at least two similar works worth 25% each of the tender value, which is Rs. 86.20 Lac, in the last five years. The similar works should be in the field of electrical works. The value of the experience submitted by the bidder shall be indexed with escalation factors ranging from 1.1 to 1.61 for different years. Additionally, the bidder should have experience in specific items of work that are 25% of the estimated cost of the work, which is not explicitly mentioned but 20% of the estimated cost is Rs 34.48 Lac (20% of Rs 172.40 Lac), and 25% of the estimated cost is Rs 43.10 Lac (25% of Rs 172.40 Lac). The bidder should also have liquid assets and/or availability of credit facilities not less than 20% of the estimated cost, which is Rs 34.48 Lac (20% of Rs 172.40 Lac). Alternatively, the bidder can have a single work experience of Rs 120.68 Lac. The bidder's prior work experience is evaluated based on the maximum value of Electrical engineering works executed in any one year during the last five years. The required prior work experience for the bidder includes having key personnel with specific years of experience, such as 2 years of experience in Degree Engineering (Electrical) and 2 years of experience in Diploma Engineering (Electrical) for works up to Rs. 1 Crore. For works above Rs. 1 Crore and up to Rs. 5 Crore, the bidder should have 2 supervisors with 2 years of experience and other personnel as specified. The bidder should have completed similar works with a total value of electrical engineering work performed in the last five years, but the exact percentage is not mentioned. The bidder needs to submit a certificate from a Chartered Accountant for the total value of electrical engineering work performed in the last five years and an annual turnover certificate from a Chartered Accountant for the last five financial years, with a breakup of related electrical works in each financial year. The bidder should have invested a minimum of 20% of the contract value of work during the implementation of the contract and provide an undertaking that they would be able to invest a minimum of 20% of the contract value of work during the implementation of the contract. The required prior work experience for the bidder is not explicitly stated in terms of years, but there are mentions of requirements for key personnel and the bidder's experience in executing similar works. The bidder should provide information on their existing commitments and ongoing works, including the value of contracts and the value of works remaining to be completed, as well as works for which bids have already been submitted. The bidder must also demonstrate their ability to execute the works by providing information on their equipment, personnel, and financial capabilities. In terms of specific values, the bidder should be able to provide overdraft/credit facilities to the extent of a specified amount to meet their working capital requirements for executing the contract, but the actual amount is not provided. The bidder should have completed at least two similar works worth 25% each of the tender value, which is Rs 86.20 Lac for electrical works, in the last five years. The bidder should also have experience in specific items of work that are 25% of the estimated cost of the work, which is Rs 43.10 Lac (25% of Rs 172.40 Lac). The bidder should also have liquid assets and/or availability of credit facilities not less than 20% of the estimated cost, which is Rs 34.48 Lac (20% of Rs 172.40 Lac). Alternatively, the bidder can have a single work experience of Rs 120.68 Lac. The bidder should be registered with any Govt./Semi Govt./PSU/Nigam in a suitable Class & Category. The bidder should have an average annual financial turnover of not less than 50% of the estimated cost, which is Rs. 86.20 Lac, in the last five years. The bidder should have satisfactorily completed at least one similar work worth 35% of the tender value, which is Rs. 120.68 Lac, or at least two similar works worth 25% each of the tender value, which is Rs. 86.20 Lac, in the last five years. The bidder should submit certificates from an officer of the rank not below Executive Engineer of Govt. or Semi Govt., indicating the names of the works completed, value of works, and period during which completed. The experience certificate from any private contractor or private organization and as a sub-contractor to prime contractor shall not be considered while evaluating the bid in compliance with the
Costs
EMD
₹ 7,00,000Document Cost
₹ 5,900Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2025_BRID3_80606_1Bid Award Id
ViewTender No
331/BRIDCUL/988/25 Dated 15.02.2025Tender Authority
Bridge Ropeway Tunnel And Other Infrastructure Development Corporation Of Uttarakhand Limited ViewPurchaser Address
-Website
http://uktenders.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
... More
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
-
-
-
... More
Group - B
54
-
-
... More
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
-
-
-
... More
Group - A
1256
-
-
... More
Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
100
-
-
... More
Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required
-
-
-
... More
Group -C
318
-
-
... More
Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required
-
-
-
... More
Group -B
10
-
-
... More
Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required
-
-
-
... More
Group -A
379
-
-
... More
Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.
-
-
-
... More
2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
5937
-
-
... More
2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
15536
-
-
... More
2 X 6 sq. mm + 1 X 4 sq. mm earth wire
940
-
-
... More
2 x 10 sq.mm + 1 x 6 sq.mm. earth wire
800
-
-
... More
4 x 10 sq.mm + 2 x 6 sq.mm. earth wire
1512
-
-
... More
4 x 16 sq.mm + 2 x 6 sq.mm. earth wire
702
-
-
... More
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 amps modular switch, connection etc. as required.
631
-
-
... More
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.
401
-
-
... More
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).
125
-
-
... More
Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.
30
-
-
... More
Wiring for light/ power plug plug with 2 X 4 sq. mm FRLC PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FRLC PVC insulated copper conductor single core cable for loop earthing as required
9965
-
-
... More
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required
483
-
-
... More
Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required
340
-
-
... More
Supplying, drawing, connecting and testing of 0.5 mm dia annealed copper conductor PVC insulated PVC sheathed telephone wire in existing conduit/wire way duct etc. as required of following sizes:
-
-
-
... More
2 Pair (4 core)
895
-
-
... More
SITC of EPBAX system extensions 16 analog trunk 16 Extenstions complete in all respest.
1
-
-
... More
Providing, laying, connecting and testing of multi-core telephone armoured cable of conductor size 0.6mm dia annealed copper conductor PVC insulated PVC sheathed jelly filled (as per DOT specification) cable along wall or ceiling or through existing pipe.
-
-
-
... More
5 Pair telephone cable
400
-
-
... More
Providing, fixing connecting and testing of under noted size of solderless telephone tag block Krone make in surface/recess in wall required size of M.S. box with hinged lockable cover duly stove enamel painted.
-
-
-
... More
10 pair tag block
9
-
-
... More
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.
-
-
-
... More
20mm dia PVC conduit
360
-
-
... More
25mm dia PVC conduit
960
-
-
... More
32mm dia PVC conduit
360
-
-
... More
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required
-
-
-
... More
1 or 2 Module (75mmX75mm)
240
-
-
... More
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required
-
-
-
... More
5/6 A switch
260
-
-
... More
3 pin 5/6 A socket outlet
260
-
-
... More
Telephone socket outlet
46
-
-
... More
TV antenna socket outlet
90
-
-
... More
Bell Push
32
-
-
... More
RJ-45 Data Socket outlet
104
-
-
... More
Supplying and fixing call bell/ buzzer suitable for single phase,
230 V, complete as required.
32
-
-
... More
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.
-
-
-
... More
1 run of cable
2080
-
-
... More
Providing, laying, connecting and testing of unarmoured TV cable RG-6 PVC insulated cable along wall or ceiling or through existing pipe.
1800
-
-
... More
Supplying and fixing brass batten/ angle holder including connection etc. as required.
570
-
-
... More
Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.
1810
-
-
... More
Installation ,Testing, Commissioning of wall bracket /ceiling
fittings of all sizes and shapes containing upto two GLS/CFL/LED
lamps per fitting, complete with all accessories including
connections etc. as required.
2141
-
-
... More
Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required
-
-
-
... More
Upto 450 mm sweep
157
-
-
... More
Extra for fixing the Louvers/ shutters complete with frame for exhaust fans of all sizes.
157
-
-
... More
Supply of surface mounting 2x2 feet 24 to 30W LED , suitable for 24Hr Continuous Operation, 3000-6000 system lumens, 110lm/W, PF0.95, THD 10% at full load, CRI80, Avg Life Class 50000Hrs @L70, complete in all respect.
80
-
-
... More
Supply of LED 4ft Batten with a nominal system lumen output of 2000 lumens and a minimum system efficacy of 100 lm/W. The luminaire shall have a rated system lifetime of 25,000 burning hours at L70. The luminaire should have a color temperature of 4000K and CRI80. The luminaire shall meet IP20 rating with THD 10% and PF 0.9. The luminaire housing should made of extrusion Al with a PC diffuser. The total power consumption should not exceed 21W (including driver).Including connection with 1.5 sqmm FRLS PVC insulated copper conductor.
525
-
-
... More
Supply of Surface mounting round 6 Watt 10 Watt , LED Down Lighter, suitable for 24Hr Continuous Operation, 660-1100 system lumens, 110lm/W, PF0.95, THD 10% at full load, CRI80, Avg Life Class 50000Hrs @L70, complete in all respect.
279
-
-
... More
Supply of Surface mounting round 12 Watt 15 Watt , suitable for 24Hr Continuous Operation, 100lm/W, PF0.95, THD 10% at full load, CRI80, Avg Life Class 50000Hrs @L70, complete in all respect.
219
-
-
... More
Supply of Surface mounting square 18 to 20 Watt , suitable for 24Hr Continuous Operation, 100lm/W, PF0.95, THD 10% at full load, CRI80, Avg Life Class 50000Hrs @L70, complete in all respect.
379
-
-
... More
Supplying of Bulkhead type light fitting complete with, wire guard, holder, electronic ballast 1 x 10 W lamp including connections etc.Including connection with 1.5 sqmm FRLS PVC insulated copper conductor as required.
14
-
-
... More
Supplying of LED mirror light luminaire with 10W watt complete with electronic ballast, lamp including connection etc. complete as required, Including connection with 1.5 sqmm FRLS PVC insulated copper conductor.
77
-
-
... More
Supply of LED Flood light 50 Watt , suitable for 24Hr Continuous Operation, 110lm/W, PF0.95, THD 10% at full load, CRI80, Avg Life Class 50000Hrs @L70, CCT 3000K, complete in all respect,
40
-
-
... More
Supplying of 9 Watt 4 Star LED Wall Light Blub complete in all respect.
570
-
-
... More
Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374- 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. 1200 mm sweep ceiling fan
483
-
-
... More
Supplying of following size exhaust fan complete with gravity louver and connection with 3 core flexible wire as required. 300mm EXHAUST FAN
157
-
-
... More
Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required
-
-
-
... More
100 A,30KA,FPMCCB
2
-
-
... More
125 A,36KA,FPMCCB
1
-
-
... More
Supplying and fixing following way ,single pole and neutral,sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
-
-
-
... More
6 Way Double Door
7
-
-
... More
8 way, Double door
3
-
-
... More
12 way, Double Door
27
-
-
... More
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
-
-
-
... More
6 way Double door
11
-
-
... More
8 way Double door
42
-
-
... More
Supply and fixing of 8 way VTPN DB with provision for MCCB (but without MCBs and incomer) complete all respect
-
-
-
... More
4 way , Double door
2
-
-
... More
8 way , Double door
1
-
-
... More
Supplying and fixing following rating, four pole, 415 V, MCB in the existing MCB DB complete with connections, testing and commissioning etc. as required Make L&T BB40400C or Eq.
-
-
-
... More
40 amps TP MCB
9
-
-
... More
63 amps TP MCB
1
-
-
... More
40 amps 4P MCB
16
-
-
... More
63 amps 4P MCB
7
-
-
... More
Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required
-
-
-
... More
40 amps
20
-
-
... More
63 amps
10
-
-
... More
Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB),having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. As required.
-
-
-
... More
25 amps
102
-
-
... More
40 amps
51
-
-
... More
Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
-
-
-
... More
Single pole
1045
-
-
... More
Double pole
13
-
-
... More
Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.
219
-
-
... More
Supply & Erection of factory fabricated & wired metal clad dust and vermin proof mounting, M.S Channel Base with botom and top cable entreis Electrical control panel with TPN ACB (65KA, 4 Pole Elect draw out Micor Processer Release IPR2) and TPN MCCB's (four Pole 36 KA with thermal magnatic release) switches and instrument chamber etc. complete in all respect. The instrument chamber shall be separate and shall comprise of flush type/digital ammeter Voltmeter, Selector switches for ammeter and Voltmeter, instrument fuses current transformer etc. The Board shall have suitable capacity electrolytic aluminium busbars as per IS8623 insulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches enty boxes shall be complete with suitable cable end boxes reverse. The job includes the grounting of the board as per directions of Engineer-in-charge. All out goings of 100 Amp. and above will be provided with Amp. Metre, curent transformer and selector switches etc. and insurment fuse The switch board shall be fabicated with CRCA sheet with a minimum thickness of 1.6mm/2mm. Cubical type switch board shall be of cat A & B only.
-
-
-
... More
BUILDING PANEL- ACADEMIC BLOCK -1
-
-
-
... More
Same as above item but following mountings.
-
-
-
... More
INCOMER:-
-
-
-
... More
1 No 200 Amp. 4P MCCB of 25KA (Ics=Icu) Breaking Capacity
-
-
-
... More
1 No. Multi Function Meter.
-
-
-
... More
1 Set of phase indicating lamps with Single Pole MCB.
-
-
-
... More
1 Set of ON / OFF indicating lamps with Single Pole MCB.
-
-
-
... More
BUS BARS:-
-
-
-
... More
250 Amps. TP&N aluminium bus bars (25 KA)
-
-
-
... More
OUT GOINGS:-
-
-
-
... More
2 Nos. 125 Amps. FP MCCB
-
-
-
... More
2 Nos. 100 Amps. FP MCCB
-
-
-
... More
1 Nos. 63 Amps. FP MCCB
-
-
-
... More
2 Nos. 32 Amps. FP MCCB
-
-
-
... More
2 Nos. Space & Spare
1
-
-
... More
Supply & Erection of factory fabricated & wired metal clad dust and vermin proof mounting, M.S Channel Base with botom and top cable entreis Electrical control panel with TPN ACB (65KA, 4 Pole Elect draw out Micor Processer Release IPR2) and TPN MCCB's (four Pole 36 KA with thermal magnatic release) switches and instrument chamber etc. complete in all respect. The instrument chamber shall be separate and shall comprise of flush type/digital ammeter Voltmeter, Selector switches for ammeter and Voltmeter, instrument fuses current transformer etc. The Board shall have suitable capacity electrolytic aluminium busbars as per IS8623 insulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches enty boxes shall be complete with suitable cable end boxes reverse. The job includes the grounting of the board as per directions of Engineer-in-charge. All out goings of 100 Amp. and above will be provided with Amp. Metre, curent transformer and selector switches etc. and insurment fuse The switch board shall be fabicated with CRCA sheet with a minimum thickness of 1.6mm/2mm. Cubical type switch board shall be of cat A & B only.
-
-
-
... More
BUILDING PANEL- HOSTELS AND TYPE III AND TYPE IV
-
-
-
... More
Same as above item but following mountings.
-
-
-
... More
INCOMER:-
-
-
-
... More
1 No 125 Amp. 4P MCCB of 25KA (Ics=Icu) Breaking Capacity
-
-
-
... More
1 No. Multi Function Meter.
-
-
-
... More
1 Set of phase indicating lamps with Single Pole MCB.
-
-
-
... More
1 Set of ON / OFF indicating lamps with Single Pole MCB.
-
-
-
... More
BUS BARS:-
-
-
-
... More
160 Amps. TP&N aluminium bus bars (25 KA)
-
-
-
... More
OUT GOINGS:-
-
-
-
... More
3 Nos. 63 Amps. FP MCB
-
-
-
... More
6 Nos. 40 Amps. FP MCB
-
-
-
... More
2 Nos. 32 Amps. FP MCB
-
-
-
... More
2 Nos. Space & Spare
9
-
-
... More
Supply & Erection of factory fabricated & wired metal clad dust and vermin proof mounting, M.S Channel Base with botom and top cable entreis Electrical control panel with TPN ACB (65KA, 4 Pole Elect draw out Micor Processer Release IPR2) and TPN MCCB's (four Pole 36 KA with thermal magnatic release) switches and instrument chamber etc. complete in all respect. The instrument chamber shall be separate and shall comprise of flush type/digital ammeter Voltmeter, Selector switches for ammeter and Voltmeter, instrument fuses current transformer etc. The Board shall have suitable capacity electrolytic aluminium busbars as per IS8623 insulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches enty boxes shall be complete with suitable cable end boxes reverse. The job includes the grounting of the board as per directions of Engineer-in-charge. All out goings of 100 Amp. and above will be provided with Amp. Metre, curent transformer and selector switches etc. and insurment fuse The switch board shall be fabicated with CRCA sheet with a minimum thickness of 1.6mm/2mm. Cubical type switch board shall be of cat A & B only.
-
-
-
... More
BUILDING PANEL- LAB & NCC
-
-
-
... More
Same as above item but following mountings.
-
-
-
... More
INCOMER:-
-
-
-
... More
1 No 200 Amp. 4P MCCB of 25KA (Ics=Icu) Breaking Capacity
-
-
-
... More
1 No. Multi Function Meter.
-
-
-
... More
1 Set of phase indicating lamps with Single Pole MCB.
-
-
-
... More
1 Set of ON / OFF indicating lamps with Single Pole MCB.
-
-
-
... More
BUS BARS:-
-
-
-
... More
250 Amps. TP&N aluminium bus bars (25 KA)
-
-
-
... More
OUT GOINGS:-
-
-
-
... More
4 Nos. 63 Amps. FP MCB
-
-
-
... More
5 Nos. 40 Amps. FP MCCB
-
-
-
... More
2 Nos. 32 Amps. FP MCCB
-
-
-
... More
2 Nos. Space & Spare
1
-
-
... More
Supply & Erection of factory fabricated & wired metal clad dust and vermin proof mounting, M.S Channel Base with botom and top cable entreis Electrical control panel with TPN MCCB's (four Pole with thermal magnatic release) switches and instrument chamber etc. complete in all respect. The instrument chamber shall be separate and shall comprise of flush type/digital ammeter Voltmeter, Selector switches for ammeter and Voltmeter, instrument fuses current transformer etc. The Board shall have suitable capacity electrolytic aluminium busbars as per IS8623 insulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches enty boxes shall be complete with suitable cable end boxes reverse. The job includes the grounting of the board as per directions of Engineer-in-charge. All out goings of 100 Amp. and above will be provided with Amp. Metre, curent transformer and selector switches etc. and insurment fuse The switch board shall be fabicated with CRCA sheet with a minimum thickness of 1.6mm/2mm. Cubical type switch board shall be of cat A & B only.
-
-
-
... More
BUILDING PANEL- MULTIPURPOSE HALL
-
-
-
... More
INCOMER:-
-
-
-
... More
1 No 160 Amp. 4P MCCB of 25KA (Ics=Icu) Breaking Capacity
-
-
-
... More
1 No. Multi Function Meter.
-
-
-
... More
1 Set of phase indicating lamps with Single Pole MCB.
-
-
-
... More
1 Set of ON / OFF indicating lamps with Single Pole MCB.
-
-
-
... More
BUS BARS:-
-
-
-
... More
200 Amps. TP&N aluminium bus bars (25 KA)
-
-
-
... More
OUT GOINGS:-
-
-
-
... More
4 Nos. 63 Amps. FP MCB
-
-
-
... More
3 Nos. 40 Amps. FP MCB
-
-
-
... More
2 Nos. 32 Amps. FP MCB
-
-
-
... More
2 Nos. 32 Amps. DP MCB
-
-
-
... More
2 Nos. Space & Spare
1
-
-
... More
Supply & Erection of factory fabricated & wired metal clad dust and vermin proof mounting, M.S Channel Base with botom and top cable entreis Electrical control panel with TPN ACB (65KA, 4 Pole Elect draw out Micor Processer Release IPR2) and TPN MCCB's (four Pole 36 KA with thermal magnatic release) switches and instrument chamber etc. complete in all respect. The instrument chamber shall be separate and shall comprise of flush type/digital ammeter Voltmeter, Selector switches for ammeter and Voltmeter, instrument fuses current transformer etc. The Board shall have suitable capacity electrolytic aluminium busbars as per IS8623 insulated with heat shrink sleeving and mounted on non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches enty boxes shall be complete with suitable cable end boxes reverse. The job includes the grounting of the board as per directions of Engineer-in-charge. All out goings of 100 Amp. and above will be provided with Amp. Metre, curent transformer and selector switches etc. and insurment fuse The switch board shall be fabicated with CRCA sheet with a minimum thickness of 1.6mm/2mm. Cubical type switch board shall be of cat A & B only.
-
-
-
... More
BUILDING METERING PANEL- TYPE-I, II
-
-
-
... More
Same as above item but following mountings.
-
-
-
... More
INCOMER:-
-
-
-
... More
1 No 40 Amp. 4P MCCB of 25KA (Ics=Icu) Breaking Capacity
-
-
-
... More
1 No. Multi Function Meter.
-
-
-
... More
1 Set of phase indicating lamps with Single Pole MCB.
-
-
-
... More
1 Set of ON / OFF indicating lamps with Single Pole MCB.
-
-
-
... More
BUS BARS:-
-
-
-
... More
60 Amps. TP&N aluminium bus bars (25 KA)
-
-
-
... More
OUT GOINGS:-
-
-
-
... More
3 Nos.32 Amps. DP MCB
-
-
-
... More
2 Nos. 25 Amps. DP MCB
-
-
-
... More
4 Nos. Single Phase Energy Meter
-
-
-
... More
2 Nos. Space & Spare
2
-
-
... More
Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required. Details of cost for one each
14
-
-
... More
Earthing with G.I. earth plate 600 mm x 600 mm x 6 mm thick including accessories , and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but with charcoal or coke and salt) as required.
34
-
-
... More
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
820
-
-
... More
Supplying, installation, testing & commissioning of heat
detector operating at 54ºC/57ºC with rate of rise cum fixed
temperature (dual thermistor) type with mounting base
complete with all connection etc. as required.
2
-
-
... More
Supplying, installation, testing & commissioning of smoke detector with builtin LED and mounting base complete with all connections etc. as required.
128
-
-
... More
Supplying, installation, testing & commissioning of manual call boxes of MS construction in surface/recess with stainless steel chain & hammer assembly complete with glass and push button etc. as required.
40
-
-
... More
Supplying, installation, testing & commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required.
71
-
-
... More
Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.
15
-
-
... More
Supplying, installation, testing & commissioning fire alarm sounder with facility to make announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for operation with amplifier i/c line matching transformer etc. complete as required.
25
-
-
... More
FIRE ALARM CONTROL PANEL
-
-
-
... More
Supplying, installation, testing & commissioning of main control and indicating panel made out of 16 SWG MS sheet to accommodate the following items duly powder coated in approved colour with louvers for ventilation, locking arrangement, audio and visual indication for fire alarm and public address system, monitoring system including connections, interconnections etc complete as required.
-
-
-
... More
6 Zone panel for fire alarm system
-
-
-
... More
100 Watt amplifier racks suitable for operation on 230V
AC/24V DC supply conforming to IEC-268-3 complete with all
accessories as required - 2 Nos.(one to act as standby)
-
-
-
... More
Talk back master station with LED PTT (press to talk) push
button for operation on 230V AC/24 V DC supply conforming
to IEC-268 for simplex mode of operation/communication
suitable for 20 Nos.talk back unit -1 set.
-
-
-
... More
Annoucement control desk suitable for selection of different
zones selectively and ON ALL CALL switch with visual
indication etc. complete as required -1 set.
-
-
-
... More
Amplifier change over switch for inter changing amplifier -1 No.
Monitor panel for loudspeaker complete with output
selector, ON/OFF switch, fuse, visual indications etc.
complete as required- 1 No.
-
-
-
... More
Gooseneck microphone with stand and ON/OFF switch- 1 No.
Main ON/OFF switch, fuse indication lamps, DC and AC
voltmeters & ammeters, terminal blocks etc. complete as
required -1 set.
-
-
-
... More
Battery charger trickle cum boost to take complete load of
fire alarm & PA system complete with all accessories
including providing & fixing of 2 nos.12 volt, 60 AH each
sealed maintenance free batteries -1 set.
13
-
-
... More
Supplying, installation, testing & commissioning talk back slave station in surface/recess suitable for operation on simplex mode complete with P.T.T. knob & speaker/microphone enclosed in a M.S.(16 SWG)/ ABS box with break glass in front etc. complete as required.
35
-
-
... More
Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required
2550
-
-
... More
Supply , Installtion , Testing and Comissioning of Landline Speaker Phone With Caller Id.
46
-
-
... More
Supply , Installtion , Testing and Comissioning of 24 PORT Network Switch Layer 2
4
-
-
... More
Supply , Installtion , Testing and Comissioning of 8 PORT Network Switch Layer 2
2
-
-
... More
Supply , Installtion , Testing and Comissioning of 4U networking/server rack
5
-
-
... More
Supply , Installtion , Testing and Comissioning of CAT 6A patch cord 3 feet .
102
-
-
... More
Supply , Installtion , Testing and Comissioning of CAT 2 pair telephone line cord 1.5 feet .
46
-
-
... More
Supply , Installtion , Testing and Comissioning of 1 KVA UPS with AVR.
41
-
-
... More
Laying of one number PVC insulated and PVC sheathed / XLPE power Cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.
-
-
-
... More
Up to 35 sq.mm.
60
-
-
... More
Above 35 sq.mm. and up to 95 sq.mm.
300
-
-
... More
Above 95 sq.mm. and upto 185 sq.mm.
60
-
-
... More
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering.
-
-
-
... More
Up to 35 sq.mm.
60
-
-
... More
Above 35 sq.mm. and up to 95 sq.mm.
300
-
-
... More
Above 95 sq.mm. and upto 185 sq.mm.
60
-
-
... More
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required
-
-
-
... More
Up to 35 sq.mm.
10
-
-
... More
Above 35 sq.mm. and up to 95 sq.mm.
50
-
-
... More
Above 95 sq.mm. and upto 185 sq.mm.
15
-
-
... More
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required
-
-
-
... More
Upto 35 sq. mm (clamped with 1mm thick saddle
20
-
-
... More
Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp
55
-
-
... More
Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp
15
-
-
... More
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.
-
-
-
... More
Upto 35 sq. mm (clamped with 1mm thick saddle)
50
-
-
... More
Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)
15
-
-
... More
Supply of following siz of 1.1KV grade multicore aluminium conductor XLPE insulated and PVC shethed armoured cable as per IS 7098:1988 with up to date amendment
-
-
-
... More
3.5 x 240 sq.mm.
150
-
-
... More
3.5 x 120 sq.mm
70
-
-
... More
3.5 x 95 sq.mm
280
-
-
... More
3.5 x 50 sq.mm
370
-
-
... More
3.5 x 35 sq.mm
40
-
-
... More
3.5 x 25 sq.mm.
20
-
-
... More
4 x 10 sq.mm
140
-
-
... More
Supplying and making cable end terminations with brass compression gland and aluminium lugs for following size of PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required.
-
-
-
... More
3½ X 25 sq. mm (28mm)
2
-
-
... More
3½ X 35 sq. mm (32mm)
4
-
-
... More
3½ X 50 sq. mm (35mm)
12
-
-
... More
3½ X 95 sq. mm (45mm)
8
-
-
... More
3½ X 120 sq. mm (45mm)
2
-
-
... More
3½ X 225 sq. mm (62mm)
2
-
-
... More
3½ X 240 sq. mm (62mm)
2
-
-
... More
4 X 10 sq. mm (25mm)
4
-
-
... More
Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.
-
-
-
... More
100mm dia
85
-
-
... More
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.
-
-
-
... More
100 mm wide x 50 mm depth x 1.6 mm thickness.
95
-
-
... More
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.
-
-
-
... More
100 mm wide x 50 mm depth x 1.6 mm thickness.
28
-
-
... More
P&F 9kg ABC MAP-90% Powder based Fire Extinguisher, Applicable Fire Class A, B & C, EPDM Rubber Hose, NRV Valve and Helium Leak Detection Tested, Internal Coating - Epoxy Powder and External Pure Polyester Powder Coated (UV resistant), IS 15683:2006 Marked.
34
-
-
... More
P&F of CO2 Portable & Trolley Fire extinguisher, 4.5kg Carbon-Dioxide type Flat base Horn Including Valve, High Pressure Rubber Wire Braided Discharge Hose of not less than 10 mm dia. & complete in all respects including initial fill with CO2 Gas confirming to IS:15222.
34
-
-
... More
Excavating trenches of required width for pipes cables etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m ncluding getting out the excavated soil , and then returning the soil as required , in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed , within a lead of 50 m.
-
-
-
... More
Pipes, cables etc. exceeding 80 mm dia . But not exceeding 300mm dia.
245
-
-
... More
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :
-
-
-
... More
100 mm nominal bore (pipe in pump room & pump room to FFTG shaft)
245
-
-
... More
Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904
as required :
-
-
-
... More
2 way - 100 mm dia M.S. Pipe
7
-
-
... More
Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all
respects, as required: (Terrace Pump)
-
-
-
... More
(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520
-
-
-
... More
b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.
-
-
-
... More
(c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.
-
-
-
... More
(d) Suitable cement concrete foundation duly plastered and with anti vibration pads.
-
-
-
... More
450 lpm at 35 m Head
7
-
-
... More
Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. (for terrace booster pump)
7
-
-
... More
Providing and fixing in position the industrial type pressure
gauges with gun metal / brass valves complete as required (for terrace booster pump)
7
-
-
... More
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :
-
-
-
... More
100 mm dia.
14
-
-
... More
Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :
-
-
-
... More
100 mm dia.
7
-
-
... More
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :
-
-
-
... More
80 mm nominal bore
28.05
-
-
... More
100 mm nominal bore
232.1
-
-
... More
150 mm nominal bore
-
-
-
... More
Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :
-
-
-
... More
Single headed Gunmetal
17
-
-
... More
20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.
-
-
-
... More
40 m
17
-
-
... More
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :
-
-
-
... More
Gun metal
34
-
-
... More
Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :
-
-
-
... More
Gun metal
17
-
-
... More
Providing and fixing standard fire mans axe with heavy duty insulated rubber handle.
17
-
-
... More
Providing of FHC Door made of 16 gauge MS Sheet with frame of size 105x70mm complete door and frame assembly including all hardwares (Concealed Flush handle,Allen Key Lock, MS Hinges, 5mm Thick Float glass) & accesories . The door to be painted with fire resistance paint. The scope shall also include the painting of the frame with the same paint as the shutter or complete as per direction of Engineer-in-charge.
(Approx. size of door: 900mm Wide & 1500mm Height)
17
-
-
... More
Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.
17
-
-
... More
Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.
7
-
-
... More
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
60000
-
-
... More
Providing and fixing Fire related signages printed on photoluminescent U1000 aluminium sheet of 1.0 mm (+-10%) containing Lumigen II as base chemical, covered under UV stablized coating and of appropriate size including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc. complete in all respects as directed by Engineer-in-charge.
21
-
-
... More
Supply and laying of aluminium conducter, PVC insulated armoured, served, sheeted cable 1000 bolts grade at a depth of 750mm below ground level over a cushion of 75mm thick sand alround and protected with burnt bricks on sides and top on surface, the cable run shall be fixed on M.S. clamps etc. of suitable size.
-
-
-
... More
3CX6Sqmm AL XLPE Cable
230
-
-
... More
Supply & fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respects. The armouring of the cable shall be properly connected with the earth as per dire
-
-
-
... More
3CX10Sqmm AL XLPE Cable
4
-
-
... More
3CX6Sqmm AL XLPE Cable
14
-
-
... More
Fabricating & Supply, installing, testing and commissioning of sheet steel clad floor mounting control panel having suitable size for control of 1 nos. booster pumps 5.5 KW/7.5HP each having suitable incoming MCCB, incoming voltmeter with selector switch and fuses. DOL Starter with hand reset overload cum single phase preventor type relay, Ammeters to read current in any one phase, alarm with reset push button which will automatically reset for the next cycle. (As per the Technical Specifications) (At Terrace floor)
7
-
-
... More
Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.
-
-
-
... More
150 mm width x 50mm depth x 1.6 mm thickness.
145
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements