Bridge Ropeway Tunnel And Other Infrastructure Development Corporation Of Uttarakhand Limited Tender
View complete overview of Uttarakhand BRIDCUL Tender
Bridge Ropeway Tunnel And Other Infrastructure Development Corporation Of Uttarakhand Limited - BRIDCUL Tender
Eprocure
Opening Date25 Oct 2021
Closing Date26 Nov 2021
Tender Amount₹ 12,77,70,000
Costs
EMD
₹ 12,78,000Document Cost
₹ 5,900Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2021_BRID2_37812_1Bid Award Id
ViewTender No
1673/BRIDCUL/678/13/2021 Dated 13.10.2021Tender Authority
Bridge Ropeway Tunnel And Other Infrastructure Development Corporation Of Uttarakhand Limited ViewPurchaser Address
-Website
http://http://bridcul.com/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil, Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia
175.95
-
-
Supplying and filling in plinth with Jamuna sand/local under floors, including watering, ramming, consolidating and dressing complete.
64.32
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)
19.1
-
-
Providing and laying in position cement concrete of specified grade
excluding the cost of centering and shuttering - All work up to plinth
level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone
aggregate 40 mm nominal size)
547.76
-
-
Providing and laying in position cement concrete of specified grade
excluding the cost of centering and shuttering - All work up to plinth
level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone
aggregate 40 mm nominal size) in Parking
124.4
-
-
P/L cement concrete - all works upto plinth level : 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)
11.67
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40
mm nominal size)
48.35
-
-
Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).
144.7
-
-
Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.
144.7
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)
40.49
-
-
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)
26.72
-
-
Providing and filling in position, blown bitumen in expansion joints
2.05
-
-
Providing and fixing sheet covering over expansion joints with iron screws Aluminium fluted strips 3.15 mm thick. 200 mm wide
164.14
-
-
Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works upto plinth level
497.99
-
-
P/L RCC M25 design mix for columns, pillars piers etc.
487.59
-
-
Add for using extra cement in the items of design mix over and above the specified cement content therein.
205.1
-
-
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:3 (1 cement :3 coarse sand)
82.41
-
-
Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)
527.27
-
-
Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.
527.27
-
-
Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).
139.1
-
-
Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.In cement mortar
416.17
-
-
Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area beyond 3 sq. metres
47
-
-
Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.
2971.4
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)
270.27
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)
105.07
-
-
Brick work with F.P.S. bricks of class designation 75 in superstructure Cement mortar 1:6 (1 cement : 6 coarse sand)
825.94
-
-
Brick work with common burnt clay selected F.P.S. (non modular) bricks of class designation 7.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand)Above plinth level upto floor V level
5.98
-
-
Providing and fixing 18 mm thick gang saw cut, mirror polished,
premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
16.5
-
-
Ceramic glazed tiles as per TAC
172.42
-
-
Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) NON decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.
105.53
-
-
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper
51
-
-
Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete.250x10 mm
104
-
-
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :100 mm
102
-
-
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than gradeAC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :100 mm
2
-
-
Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to rand screws etc. complete :300x16 mm
102
-
-
Providing and fixing aluminium sliding door bolts, ISI marked anodised(anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm
1
-
-
Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineerin- Charge. 80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern.
1200
-
-
12 mm cement plaster finished with a floating coat of neat cement of mix 1:3 (1 cement : 3 fine sand)
400
-
-
12mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar
4342.97
-
-
6 mm cement plaster 1:3 (1 cement: 3 fine sand)
287.87
-
-
Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.
35.4
-
-
15mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar
5516.33
-
-
Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.20 mm cement plaster
78
-
-
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
7937.47
-
-
Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water
thinnable priming coat with cement primer
4788.92
-
-
Finishing walls with water proofing cement paint of required shade New work (Two or more coats applied @ 3.84 kg/10 sqm)
1660
-
-
Finishing walls with acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sqm).
65.02
-
-
Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
6410.94
-
-
Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats
5397.6
-
-
Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture
248.22
-
-
Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture
7.02
-
-
Providing & fixing glass panes with putty and glazing clips in steel doors,windows, clerestory windows, all complete with 4.0 mm thick glass panes
166.38
-
-
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
108572.5
-
-
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Hot finished seamless type tubes
10050.16
-
-
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Hot finished seamless type tubes
216
-
-
Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.
20749.65
-
-
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm
1484.79
-
-
Providing and laying Vitrified tiles in different sizes (thickness to be
specified by manufacturer), with water absorption less than 0.08 % and
conforming to I.S. 15622, of approved make, in all colours & shade, in
skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1
cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/
sqm including grouting the joint with white cement & matching pigments
etc. complete.Size of Tile 600x600 mm or 300x600mm
1012.79
-
-
Providing and laying Vitrified tiles in different sizes (thickness to be
specified by manufacturer), with water absorption less than 0.08 % and
conforming to I.S. 15622, of approved make, in all colours & shade, in
skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1
cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/
sqm including grouting the joint with white cement & matching pigments
etc. complete.Size of Tile 600x600 mm or 300x600mm
113.78
-
-
40 mm thick marble chips flooring rubbed and polished to granolithic
finish, under layer 34 mm thick cement concrete 1:2:4 (1 cement : 2
coarse sand : 4 graded stone aggregate 12.5 mm nominal size) and top
layer 6mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from 1 mm to 4 mm nominal size, laid in cement
marble powder mix 3:1 (3 cement : 1 marble powder) by weight in
proportion of 4:7 (4 cement marble powder mix : 7 marble chips) by
volume, including cement slurry etc. complete :Medium shade pigment with 50% white cement and 50% ordinary cement
1200
-
-
Marble chips skirting up to 30 cm height, rubbed and polished to granolithic finish, top layer 6 mm thick with white, black, chocolate, grey, yellow or green marble chips of sizes from smallest to 4 mm nominal size, laid in cement marble powder mix 3:1 (3 cement : 1 marble powder) by weight in proportion of 4:7 (4 cement marble powder mix : 7 marble chips) by volume : 11.12.1 18 mm thick with under layer 12 mm thick in cement plaster 1:3 (1 cement : 3 coarse sand) :Medium shade pigment with 50% white cement
and 50% ordinary cement
74.48
-
-
Providing and laying flamed finish Granite stone flooring in required design
and patterns, in linear as well as curvilinear portions of the building all
complete as per the architectural drawings with 18 mm thick stone slab
over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4
coarse sand) laid and jointed with cement slurry and pointing with white
cement slurry admixed with pigment of matching shade including
rubbing, curing and polishing etc. all complete as specified and as
directed by the Engineer-in-Charge :Flamed finish granite stone slab Jet Black, Cherry Red,Elite Brown, Cat Eye or equivalent.
1333.51
-
-
Dismantling roofing including ridges, hips, valleys and gutters etc.,
and stacking the material within 50 metres lead of:Asbestos cement sheet
2933.32
-
-
Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 1.00 mm thick with zinc coating not less than 275 gm/m²
533.7
-
-
Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J. or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gm/m²
57.65
-
-
P/F 15 cm wide 45 cm over all semi circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc. 0.63 mm thick with zinc coating not less than 275gm/m
88.4
-
-
Providing and fixing precoated galvanised iron profile sheets (size,
shape and pitch of corrugation as approved by Engineer-in-charge)
0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120
grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns
epoxy primer on both side of the sheet and polyester top coat 15-18
microns. Sheet should have protective guard film of 25 microns
minimum to avoid scratches during transportation and should be
supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping
screws of size (5.5x 55 mm) with EPDM seal, complete upto any
pitch in horizontal/ vertical or curved surfaces, excluding the cost of
purlins, rafters and trusses and including cutting to size and shape
wherever required
2846
-
-
Reinforced cement concrete work in beams, suspended floors, roofs having
slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain
window sills, staircases and spiral stair cases above plinth level up to
floor five level, excluding the cost of centering,
shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse
sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
81.17
-
-
Steel reinforcement for R.C.C. work including straightening, cutting,
bending, placing in position and binding all complete Thermo-Mechanically Treated bars of grade Fe-500D or more.
143563.83
-
-
Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work
115.77
-
-
Painting with synthetic enamel paint of approved brand and
manufacture to give an even shade :Two or more coats on new work
4200.8
-
-
Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture
176.16
-
-
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
2700.95
-
-
Providing and laying in situ seven course water proofing treatment
with APP (Atactic poly-propylene) modified Polymeric memberane
over roof consisting of first coat of bitumen primer @ 0.40 litre per
sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm,
which shall consist of blown type bitumen of grade 85/25 conforming
to IS : 702, 3rd and 5th layers of roofing membrane APP modified
Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting
of five layers prefabricated with centre core as 20 micron HMHDPE
film sandwiched on both sides with polymeric mix and the polymeric
mix is protected on both side with 20 micron HMHDPE film. 7th, the
top most layer shall be finished with brick tiles of class designation
10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed
with 2% integral water proofing compound by weight of cement over
a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and
finished neat (item of laying brick tiles shall be paid for separately). sqm 592.65
1408.93
-
-
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement
: 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal
size) over 75mm thick bed of dry brick ballast 40 mm nominal size,
well rammed and consolidated and grouted with fine sand, including
necessary excavation, levelling & dressing & finishing the top smooth
686.3
-
-
Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-chargeGI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns
(minimum), including factory painted after bending
571.2
-
-
Centering and shuttering including strutting, propping etc. and removal
of form for :
-
-
-
Foundations, footings, bases of columns, etc. for mass concrete
2789.14
-
-
Lintels, beams, plinth beams, girders, bressumers and
cantilevers
1142.78
-
-
Columns, Pillars, Piers, Abutments, Posts and Struts
964.36
-
-
Suspended floors, roofs, landings, balconies and access
platform
320.37
-
-
Stairs, (excluding landings) except spiral-staircases
102.48
-
-
Suspended floors, roofs, landings, balconies and access platform, with water proof ply 12 mm thick
1885.57
-
-
Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 12.21.1 In 75x75 mm deep chase
285.52
-
-
Demolishing cement concrete manually/ by mechanical means
including disposal of material within 50 metres lead as per direction
of Engineer - in - charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
382.61
-
-
Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 1.60 mm thickness,including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm,pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards,lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed
by Engineer-in-charge: Profile B Fixing with adjustable lugs with split end tail to each jamb
14.8
-
-
Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.40mm thick with 20mm nominal size stone aggregate.
443.53
-
-
62 mm thick cement concrete flooring with concrete hardener topping,
under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse
sand : 4 graded stone aggregate 20mm nominal size) and top layer
12mm thick cement hardener consisting of mix 1:2 (1 cement hardener
mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening
compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s
specifications. This includes cost of cement slurry, but excluding the
cost of nosing of steps etc. complete.
2713.33
-
-
Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1cement : 3 coarse sand), finished with a floating coat of neat cement. 18 mm thick
2.8
-
-
Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.20 mm cement plaster
132.6
-
-
Dismantling steel work in built up sections in angles, tees, flats and
channels including all gusset plates, bolts, nuts, cutting rivets, welding
etc. including dismembering and stacking within 50 metres lead.
43198.4
-
-
Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys,rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and direction of the engineer-incharge.( Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment).
38.16
-
-
Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade
720
-
-
Filling available excavated earth (excluding rock) in trenches, plinth,
sides of foundations etc. in layers not exceeding 20cm in depth,
consolidating each deposited layer by ramming and watering, lead up
to 50 m and lift upto 1.5 m.
1489.4
-
-
Providing and fixing precoated galvanised steel sheet roofing accessories
0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams
per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy
primer on both side of the sheet and polyester top coat 15-18 microns
using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm)
79.52
-
-
Hacking of CC flooring including cleaning for surface etc. complete
as per direction of the Engineer-in-Charge.
2704.3
-
-
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :
175.95
-
-
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe
175.95
-
-
Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of:
-
-
-
(i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.
-
-
-
IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.
-
-
-
(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.
-
-
-
(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).
55.39
-
-
Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.
-
-
-
b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.
-
-
-
c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.
-
-
-
e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineerin-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.
516.79
-
-
Design supply & installation of suspended Spider Glazing system
designed to withstand the wind pressure as per IS 875 (Part-III). The
Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/ beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2 mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured.
13.2
-
-
Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests
35
-
-
Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid
46
-
-
Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto
1 metre long with S.S. triangular plate to Eureopean type W.C. of
quality and make as approved by Engineer - in - charge.
46
-
-
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps
56
-
-
Providing and fixing white vitreous china pedestal for wash basin
completely recessed at the back for the reception of pipes and fittings.
56
-
-
Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern,
with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other ouplings in C.P. brass,including painting of fittings and cutting and making good the walls
and floors wherever required :Single half stall urinal with 5 litre P.V.C. automatic flushing
cistern
51
-
-
Providing and fixing soil, waste and vent pipes: Centrifugally cast (spun) iron socketed pipe as per IS: 3989.
-
-
-
100MM
1070
-
-
75mm
496
-
-
Providing & filling the tee /bend /collar/tapper etc., with rubber jount filler including all complete
-
-
-
Providing and fixing plain bend of required degree.100 mm dia Sand cast iron S&S as per IS - 3989
295
-
-
Providing and fixing double equal plain invert branch of required degree:100x100x100x100 mm Sand cast iron S&S as per IS 3989
135
-
-
Providing and fixing plain bend of required degree.75 mm dia Sand cast iron S&S as per IS - 3989
150
-
-
Providing and fixing double equal plain invert branch of required degree:75x75x75x75 mm Sand cast iron S&S as per IS - 3989
114
-
-
Providing and fixing 600 x 455 mm. bevelled edge mirror of Saint Gobin or Modi float glass complete with 6 mm. thick hard board ground fix to wooden cleats with CP brass screws and washers etc. complete.
47
-
-
Providing and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms.
32
-
-
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings
arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm,78 mm wide and effective height of 88 mm, weighing not less than 170 gms
32
-
-
Providing and fixing toilet paper holder :C.P. brass
40
-
-
Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :Sand cast iron S&S as per IS - 3989
75
-
-
Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron(100 mm)
528
-
-
Providing and fixing M.S. stays and clamps for sand cast iron/centrifugally cast
85
-
-
Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter
470
-
-
Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 110 mm
195
-
-
Bend 87.5° 110 mm bend
62
-
-
Shoe (Plain) 110 mm Shoe
62
-
-
Providing and fixing G.I. Pipes complete with G.I. fittings and clamps,
i/c making good the walls etc. concealed pipe, including painting
with anti corrosive bitumastic paint, cutting chases and making good
the wall :
960
-
-
Providing and fixing C.P. brass angle valve for basin mixer and geyser
points of approved quality conforming to IS:8931 15mm nominal bore
75
-
-
Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge
37
-
-
Providing and fixing CP Brass 32mm size Bottle Trap of approved
quality & make and as per the direction of Engineer-in-charge.
56
-
-
Providing & fixing of foot rest in tank
With 20x20 mm square bar
10
-
-
Providing & fixing of foot rest in tank
10
-
-
Providing and fixing in position precast R.C.C. manhole cover and frame of requiredRectangular shape 600x450mm internal dimensions
12
-
-
Providing & fixing of R.C.C manhole covering tank (600 x 600)
2
-
-
Providing and fixing plain bend of required degree Inlet Pipe 100 mm dia
20
-
-
Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
5
-
-
Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil Pipes, cables etc, not exceeding 80 mm dia.
525
-
-
Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 150 mm diameter :
525
-
-
Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 150 mm diameter S.W. pipe
525
-
-
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
87
-
-
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, totalweight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
64
-
-
Extra for depth for manholes : With Sewer bricks conforming to IS : 4885
7
-
-
Providing and fixing G.I. pipes complete with G.I. fittings including
trenching and refilling etc
-
-
-
15 mm dia nominal bore
266
-
-
20 mm dia nominal bore
256
-
-
25 mm nominal bore
220
-
-
40 mm dia nominal bore
580
-
-
50 mm dia nominal bore
550
-
-
Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :
-
-
-
15 mm nominal bore
82.8
-
-
20 mm nominal bore
72
-
-
25 mm nominal bore
58
-
-
40 mm nominal bore
113
-
-
50 mm nominal bore
105
-
-
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore
34
-
-
Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :
-
-
-
20 mm nominal bore
40
-
-
Providing and fixing gun metal non- return valve of approved quality (screwed end) :
-
-
-
25 mm nominal bore (Horizontal)
12
-
-
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support
28000
-
-
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10 kg/ sqm)
2.88
-
-
Excavation in Soil with Dozer with lead upto 100 m
Excavation for roadway in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections
450
-
-
WBM Grading 1
Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 1 as per Technical Specification Clause 405.
300
-
-
Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion cu.m 1:4:8 in foundations and floors including supply of all material, labour and T&P etc. required for proper completion of the work.(Based on PWD specifications)
150
-
-
Brick masonry work in cement mortar in substructure complete excepting pointing and plastering, as per drawing and technical specification Clauses 602, 603, 604, 1202 & 1204
57.5
-
-
Excavation for Structures
Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.
315
-
-
Brick on edge pavement with straight overburnt bricks laid on edge
including preparation of subgrade to prescribed camber and including
supply of bricks, filling joints with local sand and spreading blinding coat
1cm (3/8") depth of local sand over the entire surface and including
supply of all materials, labour and T&P etc. required for proper
completion of the work
565
-
-
Providing and fillling joint sealing compound as per drawings and technical specifications with coarse sand and 6 per cent bitumen by weight.
265
-
-
Laying Cement Concrete Pipe NP3 (burried conduits) on first class
bedding of granular material including fixing collar with cement sand
mortar 1:2 but excluding excavation, protection works, backfilling,
concrete and masonary work in head wall and parapets
50
-
-
P.C.C. grade M 20 Nominal mix (1:2:4)
150
-
-
Trenching in ordinary soil up to a depth of 60cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling with in a lead of 50m and making up the trenched area to proper levels by filling with earth
500
-
-
Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).
500
-
-
Supplying and stacking sludge at site including royalty and carriage up to 1 km (sludge measured in stacks will be reduced by 8% for payment).
500
-
-
Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation.
2500
-
-
Fine dressing the ground.
2500
-
-
Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Officer-in-charge (Cost of sludge, dump manure and / or good earth to be paid separately).
375
-
-
Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge..
375
-
-
Grassing with ‘Doob’ grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing including supplying good earth if needed (the good earth shall be paid for separately). In r
2500
-
-
Preparation of beds for hedging and shrubbery by excavating cu.m 60cm deep and trenching the excavated base to a further depth of 30cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of sta
7
-
-
Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%)
240
-
-
N.S.I
-
-
-
Providing and fixing Tata Steel Pravesh Door (Hardware GEZE Make)Ball bearing butt hinge of size 102x75x3mm with screws in SSS- Dead Bolt (Mortise Dead Lock with Euro profike cylinder(Green), Concealed Flush Bolt (98307009), D - Handle(D-Both Side - Dia 19mmX254mm(L)Geze)(Double leaf)
174.24
-
-
Providing and fixing Tata Steel Pravesh Door (Hardware GEZE Make)Ball bearing butt hinge of size 102x75x3mm with screws in SSS- Dead Bolt (Mortise Dead Lock with Euro profike cylinder(Green),D2 (Tata Steel Door swings type of any size)(Single leaf)
171.47
-
-
Providing and fixingTata Pravesh factory-made casement (openable) windows with shutter manufactured from 0.6 mm thick skin pass GI Sheet and Frame from 0.8 mm thick skin pass GI Sheet having Zn coating of 120 gsm conforming to IS277. Grill provided is made from 10 mm MS rectangular shaped bars. Outer surface of Window shutter and frame is finished with pure polyester powder coating of thickness not less than 60 micron and wood finish over and above this (If required) complete as per the direction of Engineer-in-charge
210.17
-
-
Providing and fixing C.P. brass bib cock of push button of approved quality complete as per direction by engineer in charge
105
-
-
Providing and fixing C.P. brass Pillar cock of approved quality in wash basin or other fittings as per requirement conforming to IS:8931 :15 mm nominal bore(Push type as per approval of E-in CHARGE)
8
-
-
Providing and fixing C.P. brass angle cock/ valve for basin mixer , geyser points or to other similar fittings of approved quality conforming to IS:8931(Jaguar/Parryware) :15 mm nominal bore(Push type as per approval of E-in CHARGE
120
-
-
Supply,Installation,Testing & Commissioning .of 2 Nos. support arms and backrest to mount at fixed height for handicap toilet ( of approved make) as required by Engineer in charge.
2
-
-
Supply,Installation,Testing & Commissioning .of raised toilet seat with cover for handicap toilet.( approved by Engineer in charge)
2
-
-
Supply,Installation,Testing & Commissioning .of 35 mm dia powder coated steel grab L-SHAPED CORNER RAIL (800MM+800MM) (for handicapped toilet).
2
-
-
SITC in position of adjustable type white vitreous china wash basin for handicapped complete with tracks(IR 4360-Commander or equivalent) with C.I./M.S. brackets painted white, 32 mm C.P. brass waste, C.P. brass chain with rubber plug, 32mm dia C.P. cast brass bottle with extension piece, wall flanges and union complete including cutting and making good the walls floors wherever required.
2
-
-
Letter Writing on Granite by Brass letters
15
-
-
supply, fixing or installation of IKO Cambridge Roof shingles sheet with stormtite synthetic underlayment over RCC sloping roof plastered surface including all related process of fixing as per direction of Engineer in charge.
583.18
-
-
supply& installationof IKO Cambridge Hip & ridge Plus including all related process of fixing as per direction of Engineer in charge.
71.8
-
-
EmergencyY Light & Illuminated Signages
-
-
-
Illuminated signages
40
-
-
Environmental Baseline Data Generation (Pre Construction Stage)
-
-
-
Ambient Air Quality Test
2
-
-
Noise Level Test
2
-
-
Drinking Water Quality Test
2
-
-
Soil Quality Test
1
-
-
Environmental Monitoring (Construction Stage)
-
-
-
Ambient Air Quality Test
6
-
-
Noise Level Test
6
-
-
Drinking Water Quality Test
6
-
-
Soil Quality Test
3
-
-
Dust Suppression
-
-
-
Dust Suppression at Site ( Assumption @ 2 hours/ day or as and when required)
200
-
-
Septic Waste Cleaning
-
-
-
Approximately 3000 Litres in One Tanker (3 Tankers shall be required as per EMP)
12
-
-
Capacity Building
-
-
-
Training at Site for Implementation of EMP
2
-
-
DISPOSAL of Health hazard sheet
-
-
-
Disposal of Asbestos sheet to Roorkee
13.04
-
-
Disposal of Hazardous waste( Under the Hazardous Waste(Management,handling and transboundary) Rules 2016- for Asbestos, by UEPPCB Approved vendor.
36666.5
-
-
Electrical
-
-
-
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor
single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box
and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
-
-
-
Group B
1207
-
-
Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /
recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable
etc. as required.
27
-
-
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop
earthing as required.
4110
-
-
Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit asrequired.
-
-
-
2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
5235
-
-
2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
3907.75
-
-
2 X 6 sq. mm + 1 X 6 sq. mm earth wire
1890
-
-
4 X 6 sq. mm + 2 X 6 sq. mm earth wire
2460
-
-
4 X 10 sq. mm + 2 X 6 sq. mm earth wire
1230
-
-
4 X 16 sq. mm + 2 X 6 sq. mm earth wire
400
-
-
Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone
cable in the existing surface/ recessed steel/ PVC conduit as
-
-
-
4 Pair
900
-
-
Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.
-
-
-
20 mm
400
-
-
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including
cutting the wall and making good the same in case of recessed
conduit as required.
-
-
-
20 mm ( for Telephone socket)
1275
-
-
25 mm ( for 1 & 3 phase industrial socket)
2625
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
-
-
-
5/6 A switch
387
-
-
15/16 A switch
49
-
-
3 pin 5/6 A socket outlet
387
-
-
6 pin 15/16 A socket outlet
49
-
-
Telephone socket outlet
70
-
-
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
458
-
-
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.
-
-
-
1 or 2 Module (75mmX75mm)
70
-
-
6 Module (200mmX75mm)
335
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.
16
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.
137
-
-
Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.
1026
-
-
Supplying and fixing brass batten/ angle holder including connection etc. as required.
23
-
-
Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, LED Fixtures, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.
688
-
-
Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.
458
-
-
Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.
-
-
-
Upto 450 mm sweep
25
-
-
Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes.
25
-
-
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess,
complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including
earthing etc. as required. (But without MCB/RCCB/Isolator)
-
-
-
8 way , Double door
15
-
-
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted
including earthing etc. as required. (But without MCB/RCCB/Isolator)
-
-
-
4 way (4 + 12), Double door
12
-
-
6 way (4 + 18), Double door
7
-
-
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of
following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
-
-
-
Single pole
305
-
-
Triple pole
187
-
-
Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections,
testing and commissioning etc. as required.
-
-
-
63 A
15
-
-
Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.
-
-
-
40 A
14
-
-
63 A
11
-
-
Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top
alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning
etc. as required.
78
-
-
Supplying and fixing 30 A/32A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top
alongwith 30 A/32A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
123
-
-
Cable Trays
-
-
-
Supplying, fabricating and installing following size of perforated pre painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joints with connectors, suspended from the ceiling with M.S. suspenders including bolt & nuts, painting suspenders as required.
-
-
-
150 mm width X 50 mm depth X 1.6 mm thickness
770
-
-
Supplying, fabricating and installing following size of perforated pre painted M.S. cable trays bends with perforation not more than 17.5%, in convenient sections, joints with connectors, suspended from the ceiling with M.S. suspenders including bolt & nuts, painting suspenders as required.
-
-
-
100 mm width X 50 mm depth X 1.6 mm thickness
105
-
-
Supplying, fabricating and installing following size of perforated pre painted M.S. cable trays tees with perforation not more than 17.5%, in convenient sections, joints with connectors, suspended from the ceiling with M.S. suspenders including bolt & nuts, painting suspenders as required.
-
-
-
150 mm width X 50 mm depth X 1.6 mm thickness
104
-
-
Supplying, fabricating and installing following size of perforated pre painted M.S. cable trays cross members with perforation not more than 17.5%, in convenient sections, joints with connectors, suspended from the ceiling with M.S. suspenders including bolt & nuts, painting suspenders as required.
-
-
-
150 mm width X 50 mm depth X 1.6 mm thickness
102
-
-
Providing and fixing 16 mm M.S. Fan clamps of standard shape and size in existing R.C.C. slab, including cutting chase, anchoring clamp to reinforcement bar, including cleaning, refilling, making good the chase with matching concrete, plastering and painting the exposed portion of the clamps complete.
385
-
-
Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.
73
-
-
Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
30
-
-
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
14
-
-
Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)
170
-
-
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/
terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
75
-
-
Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.
190
-
-
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
200
-
-
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.
280
-
-
Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with
85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
8
-
-
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as
required.(For horizontal run)
390
-
-
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as
required.(For vertical run)
105
-
-
Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck
nuts and spring washers etc. complete as required.
15
-
-
Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.
40
-
-
cable laying
-
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing
RCC/ HUME/ METAL pipe/existing open trence/as required.
-
-
-
Above 35 sq. mm and upto 95 sq. mm
500
-
-
Above 95 sq. mm and upto 185 sq. mm
220
-
-
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size
on wall surface and overhead as required.
-
-
-
Upto 35 sq. mm (clamped with 1mm thick saddle)
30
-
-
Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm
MS flat clamp)
30
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated
and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV
-
-
-
2 X 10 sq. mm (19mm)
28
-
-
3½ X 35 sq. mm (32mm)
24
-
-
3½ X 70 sq. mm (38mm)
8
-
-
3½ X 120 sq. mm (45mm)
4
-
-
3½ X 185 sq. mm (45mm)
4
-
-
4 X 10 sq. mm (25mm)
106
-
-
Erection of metallic/octagonal pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling
etc. as required.
-
-
-
Above 4.5 metre and upto 6.5 metre
40
-
-
Providing and making steel pole collar with cement concrete (1cement : 3 coarse sand : 6 stone aggregate 20mm) of specified size and shape including form work, plastering if required, curing etc as required. (volume of pole/ pipe not to be deducted)
3.6
-
-
Supplying and embedding following dia G.I. pipe (medium class) in pole collar/ foundation (during casting) for cable entry including bending the pipe to the required shape complete as required.
-
-
-
40 mm dia
70
-
-
Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc. as required.
-
-
-
100 mm dia
80
-
-
150 mm dia
70
-
-
Supplying and laying of following size DWC HDPE pipe ISI markedalong with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting,jointing etc.direct in ground (75 cm below ground level) includingexcavation and refilling the trench but excluding sand cushioning
and protective covering etc., complete as required.
-
-
-
63 mm dia (OD-63 mm & ID-51 mm nominal)
665.5
-
-
HT works
-
-
-
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 kV grade of following size in the existing RCC/
HUME/ METAL pipe as required.
-
-
-
Upto 120 sq. mm
140
-
-
Supplying & making of INDOOR cable end terminations with HEAT SHRINKABLE JOINTING KIT with all accessories including lugs suitable for following sizes of 3 core, XLPE Al conductor cable of 11 KV grade as required.
-
-
-
3 X120 sq mm.
6
-
-
Supplying & making of OUTDOOR cable end terminations with HEAT SHRINKABLE JOINTING KIT with all accessories including lugs suitable for following sizes of 3 core, XLPE Al conductor cable of 11 KV grade as required.
-
-
-
3 X120 sq mm.
6
-
-
Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep) and re-filling etc. as required
-
-
-
150 mm dia
40
-
-
Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/
recessed steel/ PVC conduit as required.
-
-
-
2 x 1.5 sq. mm
2400
-
-
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including
cutting the wall and making good the same in case of recessed conduit as required.
-
-
-
25 mm
1600
-
-
Networking
-
-
-
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including
cutting the wall and making good the same in case of recessed conduit as required.
-
-
-
25 mm
2300
-
-
Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.
-
-
-
1 run of cable
7010
-
-
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including
cutting the wall and making good the same in case of recessed
conduit as required.
-
-
-
25 mm
1650
-
-
Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/
recessed steel/ PVC conduit as required.
-
-
-
2 x 1.5 sq. mm
1000
-
-
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including
cutting the wall and making good the same in case of recessed
conduit as required.
-
-
-
25 mm
800
-
-
Supply, installation, testing and commissioning of following ennealed tinned electric grade copper conductor PVC insulated and PVC sheathed jelly filled armoured telecommunication cable as per specifications.
-
-
-
5 pair armoured riser cable of 0.60 mm dia copper conductor
80
-
-
10 pair armoured riser cable of 0.60 mm dia copper conductor
180
-
-
20 pair armoured riser cable of 0.60 mm dia copper conductor
120
-
-
50 pair armoured riser cable of 0.60 mm dia copper conductor
20
-
-
Supply and installation, testing and commissioning following size KRONE make telephone tag block in lockable 16 gauge sheet medium duity PVC enclosure complete as required.
-
-
-
5 pair Krone type tag block
2
-
-
10 pair Krone type tag block
6
-
-
20 pair Krone type tag block
4
-
-
50 pair Krone type tag block
1
-
-
Supply and fixing of 4 way VTPN DB IP 43, IK09 with metal door suitable for flush or surface mounting with provistion of 4 pole mccb incomer and all respept accessories as required.
2
-
-
Supply and fixing of 6 way VTPN DB IP 43, IK09 with metal door suitable for flush or surface mounting with provistion of 4 pole mccb incomer and all respept accessories as required.
21
-
-
Supply and fixing of 8 way VTPN DB IP 43, IK09 with metal door suitable for flush or surface mounting with provistion of 4 pole mccb incomer and all respept accessories as required.
6
-
-
Supply and fixing of 4 pole 160 amp 25 KA MCCB Ics=Icu=100% with one side spreader links in existing VTPN DB as required.
19
-
-
Supply and fixing of 4 pole 200 amp 25 KA MCCB Ics=Icu=100% with one side spreader links in existing VTPN DB as required.
6
-
-
Supply of 20 Watt LED Linear Metal Construction commercial batten fitting with fuse protection suitable for Polycarbonate diffuser & aluminium heat sink complete suitable for both surface & suspended Mounting, complete in all respect 2000 system lumens PF0.95, THD10%, CRI80, Sheet Thickness 0.8mm, Average Life 40000hrs @L70 with fixing clamps, nut, bolts and fixing arrangement with both side of existing MS pipe (in case of hanging )complete accessories all respect and as directed by engineer in charge., as per approved make
366
-
-
Supply of surface/Suspended LED industrial batten made of CRCA housing, LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) =120lumens/watt with Minimum system Lumens 4000 with maximum input power of 34 - 40Watt. Life of fixture (Including Driver) : 50000 burning Hrs. @ L70B50 Lumen maintenance, CCT of 6500K (SDCM=4) , CRI 80, PF 0.95 & THD10%, an operating Voltage Range of 130 - 320 VAC.Minimum Internal Surge Protection 4KV & , the fixture design should comply with EMC / EMI compliance along with BIS certification for LED Driver & Luminaire seperately. The luminaire should be flicker free (Ripple5%). Luminaire manufacture shall provide LM79 report from NABL accredited lab & LM80 report issued by LED manufacturer with fixing clamps, nut, bolts and fixing arrangement with both side of existing MS pipe (in case of hanging )complete accessories all respect and as directed by engineer in charge. Similar to Philips BN308C LED40S-6500 L120 PSU WH or eqivalent as per approved make
185
-
-
Supply of LED Highbay luminaire with a housing of Pressure Die casted Aluminium and cover of toughened and shatter-proof quality glass to ensure protection. The luminaire should have a color consistency SDCM 5, CRI 80 and CCT of 6500K. The luminaire shall be compliant with IP66 classification and impact protection of IK08 to ensure durablility. Luminaire shall be designed to emit at least 80W(10000lumens at system level) nominal lumens at a system efficacy of atleast 125 lumen/watt and maximum system wattage of 80Watt. UGR＜25 power factor 0.95 and THD 10% with a minimum inbuilt surge protection of 4kV. The luminaire should have Auto Shutdown at 325+-15V and Auto Recovery options with Loop In Loop Out model available too. he fixture should comply with the parameters as per IS10322. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters with fixing clamps, nut, bolts and fixing arrangement with both side for hanging of light in existing MS pipe/steel conduit complete accessories all respect and as directed by engineer in charge. Simailar to Philips BY325P or eqivalent as per approved make.
34
-
-
Supply of LED indoor surface downlighter suitable for general lighting. Luminaire should have polycarbonate cover with diffused optics. The luminaire should have CRI 80 and CCT of 6500K. The luminaire shall be compliant with IP20 classification.The fixture should have a minimum system efficacy of 110 lumen/Watt and a minimum system lumen output of approx 2000 lumens and maximum system wattage of 18 Watts.power factor 0.95 , THD 10%. he fixture should comply with the parameters as per IS10322. The LED driver should comply to IEC61000-3-2. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. Similar to PHILIPS make SM251C LED20S- 6500 PSU WH or eqivalent as per approved make.
97
-
-
Supply of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required, in case of rode length exceed more that 30 cm then fixing clamps, nut, bolts and fixing arrangement with both side in existing steel conduit/MS pipe as directed by engineer in charge.
458
-
-
Supply of Exhaust fan 300 mm sweep metal body with 50 HZ 230 volt ac complete with all respective accessories.
38
-
-
Supplying, installation, testing & commissioning of modular, fully bolted type, sectionallised Low Voltage Panel suitable for 415 V, 3 Phase, 4 wire 50 Hz AC supply system as per standard IEC 61439- 1 &2 as Total Type Tested Assembly and of suitable size fabricated in compartmentalized design with CRCA sheet steel of 2mm thick for load bearing member and 1.6mm for Non load bearing member. 3mm thick for gland plates. i/c cleaning & finishing complete with 9 tank process (automatic PT spray) for powder coating in approved shade, having suitable rating capacity extensible type TPN Aluminium bus bars of high conductivity as per BOQ, bus bar supports, with short circuit withstand capacity of 50kA for 1 Sec., bottom base frame of 3mm thick (multifold design), fabrication shall be done in trasportable sections, entire LENGTH panel shall have a common earth bar at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of bus bars/Copper Cables and control wiring with 2.5 Sq.mm. PVC insulated copper FRLS conductor S/C cable for voltage & Current respectively, cable alleys, i/c providing following switch gears , Panel shall be suitable for Internal Arc Test 50kA for 400mS as per IEC61641 and Siesmic Zone-IV tested , Mechanical Impact IK08-IK10 as per IEC, ACBs shall have Temperature protection for release & having display with battery backup and 20Faults Trip History : ( The board shall be dust and vermin proof with degree of protection IP 42 )
Makes : Legrand (XL3)/ Schneider (Blokset)/ Siemens (Sivacon)/L&T (Ti)
-
-
-
INCOMER:
-
-
-
1 nos. 1000A 415V, Ics=Icu=Icw=50KA, 4P ACB with MP release with LCD display having O/L, S/C , G/F Over temperature and neutral failure protection, release should have minimum 10 Nos fault history for diagnosis of fault,
-
-
-
1 nos. Digital type multi function meters (V+A+Hz) with cast resin CTs 1000/5A.
-
-
-
1 Set of phase indicating lamp with MCB
-
-
-
1 No. 1000A, 4pole onload changeover switch.
-
-
-
BUSBAR
-
-
-
1000A TPN Bus bar of aluminimum alloy.
-
-
-
OUTGOING
-
-
-
1 nos. 400A, 415V, FP MCCB of 36kA.with adjustable O/L and S/C protection.
-
-
-
2 nos. 125A, 415V, FP MCCB of 25kA.with adjustable O/L and S/C protection.
-
-
-
1 nos. 100A, 415V, FP MCCB of 25kA.with adjustable O/L and S/C protection.
-
-
-
1 nos. 63A, 415V, FP MCCB of 25kA.with adjustable O/L and S/C protection.
-
-
-
3 nos. 63A, 415V, 4P MCB of 10kA.with O/L and S/C protection.
-
-
-
2 nos. 40, 230V, 2P MCB of 10kA.with O/L and S/C protection.
-
-
-
Incommer for APFC Section 1 nos. 400A, 415V, FP MCCB of 36kA.with adjustable O/L and S/C protection.
-
-
-
1 nos. Digital type multi function meters (V+A+Hz) with cast resin CTs 1000/5A.
-
-
-
1 Set of phase indicating lamp with MCB
-
-
-
1 No. APFC Relay suitable for controlling of 12 Nos relay output.
-
-
-
250KVAR Capacitor Bank in 12 steps having MCB/MCCB for protection, Contactors as per AC6 Duty for automatic switching, having auto manual switch and indication for each step.
1
-
-
Supplying, fixing, testing & commissioning of 415V ,3Phase 50Hz, 4wire system,sheet steel clad,dust & vermin proof cubical & indoor type floor mounted, free standing Main Distribution Board with IP - 42 protection, compartmentalized design and fabricated out of 2mm/1.6mm CRCA sheet steel complete with aluminium Bus Bars, Providing & Fixing of base plate /channel, P/F the following Switchgears,complete with earth Bus Bar throughout the length of the panel,terminal arrangement for incomings/outgoings cables and also outgoing terminations for various sizes of cables,the incoming and outgoing feeders shall be accommodated in a modular multi-tier arrangement,adequate size bus duct/cable alley, Sign writing,Painting,Earthing,Numbering,Danger plate etc. Complete as requried,numbering, danger plate etc. complete as required as per specification and drawing. All MCCBs Shall be Ics=100%Icu. as per approved make
-
-
-
INCOMER:
-
-
-
1 nos. 400A 415V, Ics=36KA, 4P MCCB with TM release having adjustable O/L, S/C protection.
-
-
-
1 nos. Digital type multi function meters (V+A+Hz) with cast resin CTs 630/5A.
-
-
-
1 Set of phase indicating lamp with MCB
-
-
-
1 No. 400A, 4pole onload changeover switch.
-
-
-
BUSBAR
-
-
-
400A TPN Bus bar of aluminimum alloy.
-
-
-
OUTGOING
-
-
-
2 no. 125A, 415V, FP MCCB of 36kA.with adjustable O/L and S/C protection.
-
-
-
5 nos. 100A, 415V, FP MCCB of 25kA.with adjustable O/L and S/C protection.
-
-
-
2 nos. 63A, 415V, 4P MCB of 10kA.with O/L and S/C protection.
4
-
-
Supplying, fixing, testing & commissioning of 415V ,3Phase 50Hz, 4wire system,sheet steel clad,dust & vermin proof cubical & indoor type floor mounted, free standing Main Distribution Board with IP - 42 protection, compartmentalized design and fabricated out of 2mm/1.6mm CRCA sheet steel complete with aluminium Bus Bars, Providing & Fixing of base plate /channel, P/F the following Switchgears,complete with earth Bus Bar throughout the length of the panel,terminal arrangement for incomings/outgoings cables and also outgoing terminations for various sizes of cables,the incoming and outgoing feeders shall be accommodated in a modular multi-tier arrangement,adequate size bus duct/cable alley, Sign writing,Painting,Earthing,Numbering,Danger plate etc. Complete as requried,numbering, danger plate etc. complete as required as per specification and drawing. All MCCBs Shall be Ics=100%Icu. as per approved make
-
-
-
INCOMER:
-
-
-
1 nos. 125A 415V, Ics=36KA, 4P MCCB with TM release having adjustable O/L, S/C protection.
-
-
-
1 nos. Digital type multi function meters (V+A+Hz) with cast resin CTs 400A.
-
-
-
1 Set of phase indicating lamp with MCB
-
-
-
1 No. 125A, 4pole onload changeover switch.
-
-
-
BUSBAR
-
-
-
125 TPN Bus bar of aluminimum alloy.
-
-
-
OUTGOING
-
-
-
2 nos. 100A, 415V, FP MCCB of 25kA.with adjustable O/L and S/C protection.
-
-
-
4 nos. 63A, 415V, 4P MCB of 10kA.with O/L and S/C protection.
2
-
-
Supplying, fixing, testing & commissioning of 415V ,3Phase 50Hz, 4wire system,sheet steel clad,dust & vermin proof cubical & indoor type floor mounted, free standing Main Distribution Board with IP - 42 protection, compartmentalized design and fabricated out of 2mm/1.6mm CRCA sheet steel complete with aluminium Bus Bars, Providing & Fixing of base plate /channel, P/F the following Switchgears,complete with earth Bus Bar throughout the length of the panel,terminal arrangement for incomings/outgoings cables and also outgoing terminations for various sizes of cables,the incoming and outgoing feeders shall be accommodated in a modular multi-tier arrangement,adequate size bus duct/cable alley, Sign writing,Painting,Earthing,Numbering,Danger plate etc. Complete as requried,numbering, danger plate etc. complete as required as per specification and drawing. All MCCBs Shall be Ics=100%Icu. as per approved make
-
-
-
INCOMER:
-
-
-
1 nos. 125A 415V, Ics=25KA, 4P MCCB with TM release having adjustable O/L, S/C protection.
-
-
-
1 nos. Digital type multi function meters (V+A+Hz) with cast resin CTs 125/5A.
-
-
-
1 Set of phase indicating lamp with MCB
-
-
-
BUSBAR
-
-
-
125A TPN Bus bar of aluminimum alloy.
-
-
-
OUTGOING
-
-
-
8 nos. 40A, 230V, 2P MCB of 10kA.with O/L and S/C protection.
1
-
-
Dismantling existing electrical accessories like switch boards, switches, ceiling fans, DB's, wiring etc. by manual means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge of complete project.
1
-
-
Supply and Erecting modular type computer jack RJ 45 with screwless connector approved make with mounting plate and box with wiring connections complete.
213
-
-
Supplying & fixing of 6 Core - Optic fiber cable OM4 - Unitube Corrugated steel tape Optical Fiber Cable as per IEC 60794-1
900
-
-
CCTV
-
-
-
Supplying & fixing of U/ UTP, Cat 6 A Cable as per ANSI/TIA 568C.2 at 500 to 600 MHz suitable for (Complete in all respect) cctv
6200
-
-
Supplying & fixing of 6 Core - Optic fiber cable OM4 - Unitube Corrugated steel tape Optical Fiber Cable as per IEC 60794-1
500
-
-
FIRE ALARM SYSTEM
-
-
-
Supply and fixing of 2 Zone Conventional Fire Alarm Control Panel , Panel Operating Voltage :AC 220v 50Hz #10%, DC 24v 1 amp Operating Temperature :0º C to 50º (176)C
Operating Humidity :95% (non-condensing)
Hooter output :2A (24v DC) ,EOL :4k7 ohm, 1 per Zone, Construction :1.8mm CRCA sheet duly powder Coated ,
16 * 2 character LCD Display ,
Extra potential free contact for fire & fault
,Auto dialer connectivity facility
,Inbuilt battery charger & battery space facility
,Reset, alarm cancel, lamp test feature
,Zone wise test and isolation facility
,Protected from Hi-voltage, over-load, short-circuit,
Zone wise LED indications for fire, open and short.
7
-
-
Supply and fixing of High intensity Sounder with mounting base.
24
-
-
Providing , installation , testing & commissioning of Glass Break Type Manual Call Point
24
-
-
PA system
-
-
-
Supply of following sizes of XLPE insulated Aluminum Armoured cable, overall PVC sheathed 1.1 KV grade cables conforming to relevant IS code and technical specifications.
-
-
-
2CX10 SQMM AL ARMOURD CABLE
270
-
-
4CX10 SQMM AL ARMOURD CABLE ( for Stree Light & 1 phase industrial socket DB)
1375
-
-
3.5CX35 SQMM AL ARMOURD CABLE
380
-
-
3.5CX70 SQMM AL ARMOURD CABLE
220
-
-
3.5CX120 SQMM AL ARMOURD CABLE
190
-
-
3.5CX185 SQMM AL ARMOURD CABLE
155
-
-
Supply of LED street light fitting not more than 30W having System Efficacy 120 lm/W, system output 3600Lumens, THD 10%, Power Factor 0.95, CRI 70, CCT 5700, Full IP 66 ( with out Glue) protected single piece die cast aluminium housing having toughned glass/PC with Impact resistance IK07. LED driver should be Fully metal body Potted & Encapsulated . BIS compliant driver should sustain 440V Stress Voltage protection for 8 Hrs., High Cut off : 325V(+/- 15V) and should have feature of Auto Restart. Driver shall have 4KV Surge protection and feasibility of 10KV external SPD housed in Luminiare and confirming standard IEC60598. Including suitable size GI pipe bracket clamps, nut, bolts and washers complete all as directed. as per approved make
60
-
-
Supply of 5.0 Mtr Height Galvanized Iron OctagonalPoles having uniformly tapered polygonal shape throughout the length with straightLongitudinal welding in a single shaft. There shall not be any circumferential welding. Dimensions:Top Dia.: 70mm, Bottom Dia.: 130mm, Thickness 3mm &Base plate 200*200*12 mm. Dimension of Foundation Bolts - Length 600mm, Dia. 24mm &04 Nos. Bolts manufactured from special steel along with nuts, washer, anchor plates & Templates. SingleArm of 0.5 Mtr. Shall be provided along with .
40
-
-
Safety Equipments & Accessories
-
-
-
Supplying & laying 1.1 kv grade ISI marked synthetic rubber mats as per specifications of chief electrical inspectorate.
8
-
-
Supplying & fixing of shock treatment chart printed in hindi and english fitted in wooden frame and glass at front side and hard board at back side.
4
-
-
Supplying & fixing in position 1.1 kv rubber hand gloves.
3
-
-
Supplying of first aid box as approved by St. John Ambulance Brigade/Indian Red Cross conforming to IS : 2217 - 1963.
5
-
-
Supplying of basic Electrical and mechanical maintenance tool kit as per direction of engineer In charge.
1
-
-
HT SUB STATION WORKS
-
-
-
SITC of 11 KV, 630 Amp Outdoor type HT RMU. The RMU Should consist on one no of Load break switch (LBS) as incomer and one VCB as outgoing. The RMU should be
type tested according to IEC 62271-100, 200 & 102, IAC AFL, 21 kA for 1 sec, IP class 54, IP 67 for Tank. The rated voltage should be 12 kV, impulse withstand voltage of 75 kVp, Power frequency withstand voltage of 28 kV, rated short time current of 21 kA for 3 sec. The RMU should have SF6 gas insulation, robotic welding of gas tank. The RMU should be suitable for outdoor application. The manufacturer should have service centre in the state of uttarakhand.
1
-
-
Supply,Installation, testing & Commissioning of double pole structure suitable for 11 KV HT system as per CEA & UPCL norms & comprising of the following ,but not limited to it for completion of works . RSJ pole of 9 mtrs length of size 175 X 90 mm complete with suitable MS base plate welded at bottom base plate - 2 nos.MS channel of size 100 X 50 mm , length 4 mtrs (approx.)11 KV AB switch - 1 set , 11 KV Horn gap fuse unit - 1 set , 11 KV Lightning Arrestor , 11 KV Disc Insulator , 11 KV pin insulator 6 swg copper wire for jumpering Supply and erection of stay set complete with necessary foundation , excavation, and refilling of earth etc. as required. Concrete foundation for RJS poles burried upto a depth of 1830mm in ground in a pit of size 450 X 450 mm in CC 1:3:6 along with 200 mm copping above ground inclusive of earth work.Necessary Nut , Bolts, Clamps, operating handle for AB switch , clamping welding etc. complete as required. Painting the RSJ poles complete with two coat of red oxide and two coats of GI enamel paints complete as required.
1
-
-
Supply, installation, testing and commissioning of outdoor TYPE, OIL type transformer with copper winding having a continuous rating of 315 kVA, 11kV/415 +/- 1% V, 3 phase, 50 Hz, DY-11 vector group, The transformer shall have cable end box for indoor termination of HT cable on HT side and Cable Box for indoor termination on LT side, complete in all respects including standard accessories. It is To be installed on Top of two pole structure with proper iron angle channel support as required.Compliance to BEE Standards AND BIS Standards (IS 1180).
1
-
-
Supply OF UNDERGROUND HT CABLES
-
-
-
Supply of HT (UE) AL XLPE Cable of size 3 C X 120 sq mm
50
-
-
Supply,installation,testing and commissioning of MS C class Heavy duty pipe Inclueding forged fitting such as bends, tees, reducers,welding rods,two cote red oxide peimer and one cote post office red paint,angle,fastnor,two cote black japan etc. as follow
-
-
-
150 mm line (approx.) C Class
150
-
-
100 mm line (approx.) C Class
300
-
-
80mm line (approx.) C Class
102
-
-
25mm line (approx.) C Class
72
-
-
SITC of wrapping coating of pipe line in trenches
500
-
-
Supply,installation, testing and commissioning of single headed landing valve of 63mm dia. Made of SS hydrant valve complete with necessary fitting.
10
-
-
Supply,installation, testing and commissioning of RRL Hose pipe with 63mm dia. and 15mtr.length with SS male and female couplings.
24
-
-
Supply,installation, testing and commissioning of 63mm dia. SS short branch pipe nozzle suitable for instantaneous connection to hose coupling as required.
14
-
-
Supply,installation, testing and commissioning of MS hose box keeping two no.of RRL hose pipe and one no.of short branch pipe.
14
-
-
Supply,installation, testing and commissioning of two way fire brigade inlet connection suitable for local fire tender complete as required.
2
-
-
Supply,installation,testing and commissioning of swinging type first aid fire hose reel of 20mm internal dia and 30 mtr long with MS drum and 5mm shut of nozzle complete with fitting complete as required.
20
-
-
Supply,installation,testing and commissioning of gun matel body air release valve complete with all fitting as equired like ball valve,holdtite,suta etc.
4
-
-
Supply,installation,testing and commissioning of Cast Iron body Butterfly Valve complte with all fitting as requied like MS flange, nut bolts,washers etc.
-
-
-
100 mm
6
-
-
80 mm
4
-
-
Supply,installation,testing and commissioning of Cast Iron body Non return valve complte with all fitting as requied like MS flange, nut bolts,washers etc.
-
-
-
100 mm
4
-
-
80 mm
3
-
-
Supply,installation,testing and commissioning of Pressure Gauge. (0-10kg).
5
-
-
Supply,laying,testing and commissioning of alluminium armoud cable complete with all fitting as required like lugs,glands etc.of following sizes:
-
-
-
16mm x 4core. From pump electric panel to fire pump .
80
-
-
35mm x 3.5 core
20
-
-
10mm x 4 core
20
-
-
Supply,installation,testing and commissioning of gun matel body Ball Valve.25mm dia.
26
-
-
Supply,installation,testing and commissioning of pressure switch (maximum pressure range 10kg/sq high)for hydrant stand by and jocky pumps, complete as required.
4
-
-
Supply,installation,testing and commissioning of air vashal tank complete with all fitting like air release valve,ball valve,MS Flanges,holdtite,suta etc.(200mm dia x 2000mm length).
2
-
-
Supply,installation,testing and commissioning of Terrace tank made of zinc aluminium sheet and plastic lining 10,000 Ltr
1
-
-
Connection of terrace tank with existing water supply line
2
-
-
Supplying,Installatoin,Testing,& Commissioning of Terrace pumps of 450 lpm @ 45 mtr head
2
-
-
Supply, installation, testing and commissioning of starter for terrace pumps
1
-
-
RCC Hole Cutting
8
-
-
Digging of underground line
400
-
-
Providing and fixing anti vivration mounting for pipe line
-
-
-
100 mm dia
1
-
-
Supplying,Installatoin,Testing,& Commissioning of electric driven
-
-
-
Hydrant Pump suitable for automatic operation consisting of the
-
-
-
following complete in all respects as required.Horizontal type,multi
-
-
-
stage,centrifugal,split casing pump of cast iron body & bronze
-
-
-
impeller with stainless steel shaft,mechanical seal to ensure a
-
-
-
minimum pressure of 3.5 kg/sq.cm at highest and farthest oulet at
-
-
-
specified flow of 1620 LPM at 50 M head conforming to IS:152
-
-
-
Suitable HP Squirrel cage induction motor,TEFC synchronous
-
-
-
speed1 RPM,suitable for operation on 415 V3 phase 50 Hz,AC with
-
-
-
IP 55 protection for enclosure,horizontal foot mounted type with class
-
-
-
F insulation,conforming to IS:325.Pump set shall be assembled at
-
-
-
works and tested to satisfy performance requirements.MS fabricated
-
-
-
Common base plate,coupling,coupling guard,found bolts etc as
-
-
-
require Suitable cement concrete pump foundation duly plastered
-
-
-
with anti vibration pads.
1
-
-
Supplying,installation,testing,& commissioning of diesel engine
-
-
-
driven Horizontal type,multi stage,centrifugal pump of cast iron
-
-
-
body and bronze impeller with stainless steel shaft,mechanical
-
-
-
seal to ensure a minimum pressure of 3.5 kg/sq. cm at highest
-
-
-
and fartest outlet at specifiedflow of 1620 LPM at 50 M Head
-
-
-
conforming to IS:1520 Suitable hp,2000 RPM water cooled with
-
-
-
radiator, diesel engine conforming to relevant BS & IS standarde
-
-
-
complete with auto starting mechanism,12 volts/24 volts electric
-
-
-
starting equipment,Diesel Tank,exhaust pipe extended to1.0
-
-
-
Moutside pump house duly insulated with 50 mm thick glass wool
-
-
-
with1.0 mm thick aluminium sheet cladding,residential silencer,
-
-
-
instruments and protection as per satisfy performance requirements.
-
-
-
MS fabricated specification,stop solenoid for auto stop in the event
-
-
-
of fault with audio indications,apinted with post office red colour etc
-
-
-
as required.Pump set shall be assembled at works and tested to
-
-
-
Common base plate,coupling,coupling guard,foundation bolts etc
-
-
-
as required.Suitable cement concrete pump foundation duly plas -
-
-
-
tered with anti vibration pads.
1
-
-
Supplying,Installatoin,Testing,& Commissioning of electric driven
-
-
-
Pressurisation Pump suitable for automatic operation consisting of
-
-
-
the following complete in all respects as required.Horizontal type,
-
-
-
multi stage,centrifugal,split casing pump of cast iron body & bronze
-
-
-
impeller with stainless steel shaft,mechanical seal and flow of 180
-
-
-
LPM at 50 M head conforming to IS:1520.Suitable HP Squirrel cage
-
-
-
induction motor,TEFC,synchronous speed 2900 RPM,suitable for
-
-
-
operation on 415 V,3 phase 50 Hz,AC with IP 5 protection for
-
-
-
enclosure,horizontal foot mounted type with class F insulation
-
-
-
conforming to IS:325.MS fabricated Common base plate,coupling,
-
-
-
coupling guard, foundation bolts etc as required Suitable cement
-
-
-
concrete pump foundation duly plastered with anti vibration pads.
1
-
-
Fabrication and Supplying of Fire Fighting Panel of cubical
-
-
-
construction, floor mounted type, fabricated out of 2mm. thick CRCA
-
-
-
sheet, compartmentalized with hinged lockable doors, dust and
-
-
-
vermin proof, powder coated of approved shade after 7 tank treatment
-
-
-
process, cable alley, interconnection, having switchgears and
-
-
-
accessories mounting and internal wiring, earth terminal, numbering
-
-
-
etc.complete in all respects, suitable for operation on 415 V, 3 phase
-
-
-
50 Hz. AC supply with enclosure protection class IP 52 as required.
-
-
-
(INCOMER & METERING)
-
-
-
- 200A TP 36 KA MCCB with Inbuilt thermal magnetic release
-
-
-
- Voltmeter (0-500 Volts) with selector switch
-
-
-
- 300 Ammeter with selector switch & CT's etc.
-
-
-
- Set of 3 Phase indicating lamp.
-
-
-
- Set of Al. bus bar of 400A capacity.
-
-
-
(OUTGOING)
-
-
-
(a) MAIN FIRE PUMP- Nos
-
-
-
100A TP 36 KA MCCB with inbuilt thermal magentic release
-
-
-
withsuitable for 40HP fully automatic Star delta starter with Power
-
-
-
Contrator, over load protection, current sensing type single phase
-
-
-
preventor complete with all accessories and internal wiring required
-
-
-
for automatic operation selector switch for local/remote, auto/manual
-
-
-
/OFF operation.
-
-
-
(b) JOCKEY PUMP - Nos
-
-
-
63A TP 10 KA MCB with inbuilt thermal magnetic release with
-
-
-
suitable for 10 HP fully automatic Dol starter with Power Contractor,
-
-
-
over load protection, current sensing type single phase preventor
-
-
-
complete with all accessories and internal wiring required for
-
-
-
automatic operation, selector switch for local/remote, auto/manual/
-
-
-
OFF operation.
-
-
-
(c) DIESEL ENGINE CONTROL - Nos.
-
-
-
Control for 24V Diesel Engine comprising-
-
-
-
Auto/manual selector switch and 3 attempt starting device, timers
-
-
-
and relays as required, push buttons, start/stop in manual mode.
-
-
-
Indication lamp for High/low lub. Oil pressure, High water Temp.
-
-
-
and Engine ON Indication.
1
-
-
FIRE EXTINGUISHERS
-
-
-
Supply and installation of ABC powder stored pressure type portable fire extinguisher ISI marked 15683- 2006 & ISO - 9001, complete as required capacity - 6 kg
45
-
-
Supply and installation of CO2 type fire extinguisher ISI marked steel body 15683- 2006 & ISO - 9001, complete as required capacity - 4.5 kg
45
-
-
Supply and installation of Mechanical Foam (AFFF) type fire extinguisher ISI marked steel body 15683- 2006 & ISO - 9001, complete as required capacity - 9 ltr
5
-
-
Supply,installation of fire Bucket as per IS spacification with stand (holding four bucket).
8
-
-
Water Lifting Pump
-
-
-
Supply, Installation, Testing and Commissioning of 5 HP Electric Driven Fire Pump suitable for auto/maual operation & consisting of following: complete in all respect like pump, motor, coupling etc.
2
-
-
Fabrication, Supplying, Installation, Testing & Commissioning of Starter for Pumps
2
-
-
SITC of Cable for pump 4cx6 mm Aluminium armoured
30
-
-
SITC of Foot Valve
2
-
-
Supply and fixing of GI line of 50 mmdia for pump room
12
-
-
Supply,installation,testing and commissioning of Cast Iron body Butterfly Valve complte with all fitting as requied like MS flange, nut bolts,washers etc.
2
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements