Yamuna Expressway Industrial Development Authority Tender

Lintels, beams, plinth beams, girders, bressumers and cantilevers.UPPWD SOR-2020/5.9.5

Columns, pillars,piers,abutments, posts and struts.UPPWD SOR-2020/5.9.6

Suspended floors, roofs, landing, balconies and access platform. UPPWD SOR-2020/5.9.3

Providing and laying in position Specified grade of rainforced cement concrete, excluding the cost of centering and shuttering. finishing and rainforcment- All work up to plinth level (cast in situ) 1:1½:3(1 cement: 1½coarse sand: 3 graded stone aggregate 20mm nominal size) Based on SOR-2020/5.1.2

Providing and laying in position Specified grade of rainforced cement concrete, excluding the cost of centering and shuttering. finishing and rainforcment- All work above plinth level up to floor 5 level. Providing and fixing tie bolt, spring coil and plastic cone in wall shuttering complete as per direction in charge.1:1½:3(1 cement: 1½coarse sand: 3 graded stone aggregate 20mm nominal size) Based on SOR-2020/5.2.2

Steel reinforcement for R.C.C work including straightening , cutting , bending, placing in position and binding all complete upto plinth level Thermo mechanically treated bars(Based on UPPWD SOR-2020/5.22.6

Brick work with common burnt clay (non modular) bricks o class designation 150 in foundation and plinth in: Cement mortar 1:6 (1 cement: 6 coarse sand ).(Based on UPPWD SOR-2020/6.1.2

Brick work with common burnt clay (non modular) bricks o class designation 150 in foundation and plinth in: Cement mortar 1:6 (1 cement: 6 coarse sand ).(Based on UPPWD SOR-2020/6.1.2

12mm cement plaster of mix1:6 (1 cement:6 coarse sand).Based on UPPWD SOR-2020/13.4.2

15mm cement plaster of mix1:6 (1 cement:6 coarse sand).Based on UPPWD SOR-2020/13.5.2

Steel work welded in built up section/framed work including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer using structural steel etc.In gratings,frames,guard bar,ladder,railing,brackets,gates and similar. Based on UPPWD SOR-2020/10.25.2

Painting with synthetic enemel paint of approved brand and manufacture to given an even shade.Two or more coats. Based on UPPWD SOR-2020/13.61.1

Washed stone grit plaster on exterior walls height upto 10 mtr. Above ground level, in two layers, under layer 12mm cement plaster 1:4 (1) cement: 4 coarse sand), furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 2kg of cement per square metre, top layer 15mm cement plaster 1:11/2:2 (1 Cement: 11/2 coarse sand: 2 stone chipping 10mm nominal size), in panels with groove all around as per approved pattern, including scrubbing and washing the top layer with brushes and water to expose the stone chippings, complete as per specification and direction of Engineer in-charge (Payment opfr providing grooves shall be made separately).Based on UPPWD SOR-2020/13.72

Forming groove of uniform size from 12x12mm and upto 25x15mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing alluminium channels of appropriate size and thickness (not less than 2mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and dorection of the Engineer-in-charge. UPPWD/SOR/2020/13.76

Finishing walls with water proofing cement paint of required shade :New work (Two or more coats applied @ 3.84 kg/10 sqm)UPPWD/SOR/2020/660+661/p-23

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :300mm dia R.C.C. pipeUPPWD/SOR/2020/19.6.3

Providing and fixing C.P. brass bib cock of approved quality conforming to IS: 8931: 15mm nominal boreUPPWD/SOR/2020/18.49.1

Providing and fixing brass stop cock of approved quality:20 mm nominal bore UPPWD/SOR/2020/18.16.2

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work: 32mm nominal outer dia pipesUPPWD/SOR/2020/18.9.4

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:15 mm nominal bore UPPWD/SOR/2020/18.18.1

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (Based on UPPWD SOR-2020/18.48)Circular tank.

Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). (Based on UPPWD SOR-2020/10.13.1)

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35mm thick including ISI marked stainless steel butt hinges with necessary screws. (Based on UPPWD SOR-2020/9.21.1)

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :300x16mm (Based on UPPWD SOR-2020/9.96.1)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm (Based on UPPWD SOR-2020/9.100.1)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :150x10mm (Based on UPPWD SOR-2020/9.97.4)

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. (Based on UPPWD SOR-2020/17.1.1)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White vitreous China wash basin size 630x450 mm with a pair of 15mm C.P. brass pillar taps. (Based on UPPWD SOR-2020/17.7.1)

Providing and fixing unplasticised PVC connection pipe with brass unions:30 cm length: 20 mm nominal bore UPPWD/SOR/2020

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe : 32mm dia. (Based on UPPWD SOR-2020/17.28.1.1)

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931 : 15mm nominal bore (Based on UPPWD SOR-2020/18.53.1)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall15 mm nominal outer dia Pipes (Based on UPPWD SOR-2020/18.7.1)

20 mm nominal outer dia Pipes (Based on UPPWD SOR-2020/18.7.2)

Providing and fixing PTMT stop cock of approved quality and colour.15mm nominal bore, 86mm long. Weighing not less than 88 gms. (Based on UPPWD SOR-2020/18.55.1)

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick :Float glass panes. 4mm thick glass pane (Based on UPPWD SOR-2020/9.7.7.1)

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size), including necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With bricks of class designation-150 (Based on UPPWD SOR-2020/18.36.1)

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:100 x 100mm size P type: With bricks of class designation-150 (Based on UPPWD SOR-2020/19.4.1.1/P-354)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25mm thick. (Based on UPPWD SOR-2020/11.26.1)

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.Based on UPPWD SOR-2020/11.27

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.Based on UPPWD SOR-2020/8.31/11.36

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.Based on UPPWD SOR-2020/11.37

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge.(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. SUB HEAD : 22- WATER PROOFING 1548(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :With average thickness of 120 mm and minimum thickness at khurra as 65 mm.Based on UPPWD SOR-2020/22.7.1