Varanasi Development Authority Tender

Wiring wire 1.5sqmm 2 core PSR at Rajghat Bridge file

Supply & fixing of LT cable armored served sheathed cables 1100 V grade depth of 750mm below ground or cable shall be run on surface fixed on MS clamp SOR 2018 SI No.501

50 Sqmm × 3.5

25 Sqmm × 3.5 core

16 Sqmm × 4 core

Supply and burring of safe earthing electrode T-19 (Hot Dip Galvanized), Length up to 2000mm, outer pipe 50mm, inner pipe 25, terminal dia 12 mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square CI frame with hinged cover & masonry housing (from electrode terminal to switch board, cost of 25 × 3 GI. Strip will be extra) Make : As approved in U.P.P.W.D., & C.P.R.I. Certified SOR 2018 SI No. 725 (A)

Supply and fixing of plain or pin type copper tin plated cable socket (lug) SOR 2018 SI No. 504 25 Sqmm

10/16 Sqmm

S/B of pole earthing with 20mm die × 2000mm long M/S Rod connected with pole by 6 to 4 swg GI wire complete. As per UPPCL

S/F of HDPE Pipe 4Kg./Cmsq size 63mm die. PSR at Rajghat Bridge file

S/F of HDPE Pipe 4Kg./Cmsq size 50mm die. PSR at Rajghat Bridge file

HDD Drilling by manual of mechanical method PSR at Rajghat Bridge file

S/F of GI wire as continuity wire. SOR 2018 SI No.628

S/F of GI strip 25mm × 3mm size. SOR 2018 SI No. 716

S/F of MCB DP 6 to 32 amp. CAT - A SOR 2018 SI No. 1009

Extra CC work as required at site for plinth, foundation for panel etc. as given of 4:2:1 CC Foundation in 2cm stone grit, sand mortars and cement. SOR 2020 SI No. 279b

Supply and fixing following capacity of automatic street light cubicle control panel painted with anticorrosive alkali and acid proof paint consisting of time switch TSO 100 series with contactors, HRC fuses, isolating switch metering instrument & instrument box with CTs etc. in case of TPN. As directred by E.I. Make - Havells, L&T, Cemenence. 40 A TPN

Supply & fixing of 12.5 mtr High mast shaft of approved make with rising system hot dip glavanized inside & out side dip, heaving pole sheet thickness 3 mm. Top dia minium 150 mm, Bottom dia 310 mm base plate 25 mm thick suitable for wind velocity as per IS 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame suitable for 6 luminaries & its control gear boxes 0.75 HP power tool moter, 3 point suspension system with steel wire rope 6 mm dia, double drum winch, including making suitable foundation as per manufature drawing/ site reuiment along with foundation bolts nuts, washers, anchor plates etc completee in all respect 12.5 High SOR 2018 SI No. 651

Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 150 Watt. Confirming to IP 66 protection complete in all respect. (Make - Crompton, Phillips, Bajaj, Hellonix) SOR 2018 SI No. 1454

Supply and fixing of 6sqmm×4core copper cable Rate based on Police Line Mast file

Supply and erection of factory fabricated and wired metal clad dust and vermin proof floor mounting panel TPN switch board complete with the following HRC type heavy duty TPN fuse switches with fuses and instrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type ammeter, voltmerer, selector switches for ammeter and voltmeter, instrument fuses, current transormer etc. The board shall have suitable capacity electroytic alumininum busbars as per IS8623 istulate with heat shrink sleeving and mountend on non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches shall be complete with suitable cable end boxes, reverse entery boxes in case of pedestaal type, cable sockets, compression glands and indicating lamp on incoming etc. The job includes the grounting of the board as per direction of Engineer-in-Charge. All coutgoing switches of 100 Amp. and above will be provided with ampere metre current transformers and selector switches and instrument fuses etc. The switches board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm/2 mm. Cubicle type switch board shall be of cat A B & B-II and pedestal type for Cat-B and C only. Incommer 200Amp. TPN-1 No. (a) 100 Amp. TPN-2 Nos. SOR 2018 SI No. 802 (a)