Uttar Pradesh State Industrial Development Authority Tender

12mm Cement plaster with cement mortar in proportion of 1:4 cement & coarse sand of single coat for interior plastering upto floor two level including internal rounded angles chamfers, and rounded angles not exceeding 80mm in girth and finished even and smooth.

Providing and laying cement concrete in 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) and curing complete, lncluding cost of form work. ln Foundation and floors.

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. including cost of centering, shuttering, finishing and excluding reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) i) upto plinth level

Steel reinforcement for R.C.C. work including straightening, cutting, ending, placing in position and binding all complete upto plinth level.Cold twisted bars

Steel wok in built up tubular (round,square or rectangular hollow tubes etc.) truses etc. including cutting. Hoisting fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. (Hot finised welded type tubes.

Retro"Reflectivesheeting type-lv with 4 mm thick ACIvI Single Side Providing & llxing of reflective signs with a corrosion resistant 4 mm thick with 0.4 to 0.5 mm both side aluminium skin aluminium composite panel face to be fully covered with High tntensity prismatic sheeting type lV as per IRC-67:20'12 retro reflective sheeting with back f.ame NIS angle of 35x35x5 mm. Legends , letters , numerals and borders etc should be as per MoRTH specification No- 80'1.3.7 .The sheeting shall have a pressure - sensitive adhesive of the aggressive - tack type requiring no heat , solvent other preparation for adhesion to a smooth clean surface, in a manner recommended by the sheeting manufacturer. The ACIVI (Aluminium Composite Materials) shall be lixed on the Back frame MS Angle wilh riveting. [.4lcro prismatic type lV Retro reflective sheeting confiming to ASTM 04956-09 shall be Pressure fixed The Retro reflective sheeting shall be tested for a certillcate of having the sheeting tested Ior coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from lntemational/Government Laboratory/ lnstitute by the manufacturer of the sheeting and in case the certlficate is obtained from international condition. il should also be obtained from lndian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artillcial accelerated weathering requ;rements from a reputed laboratory in lndia can be accepted provisionally. ln such a situation, the Employer/Client, if so desires, could seek for a perFonnance guarantee which would be released after receipt of certilicale meeting the requirement of three years outdoor alhering of ihe sheeting as per IRC 67:2012 & Proof of the same Repoft shall be uploaded which quoting tender. The rate shall include all materials, labour, T&P, transportation, installation and lncidentals all complete as per direction of the Engineer-in-Charge.

Cleaning Jungles including uprooting of rank vegetation grass,bushes, wood trees and sapling of girth upto 30cm measured at a height of 1 meter above ground level and removal of rubbish upto a distance of 50 meters out side the periphery of area cleared.