Uttar Pradesh Small Industries Corporation Limited Tender

P/L Cement Concrete in 1:6:12 (1 cement:4 Fine Sand: 8 graded Stone Aggregate 40mm Nominal Size)……………..complete item. Sch no.275b

M-150 brick work in 1:4 Cement & C. Sand Mortar in Foundation and plinth…Complete Item.sch item no.305

R.C.C works with cement approved coarse sand and (3/4")gauge approved stone Grite in the proportion 1:1.5:3 in column foundation………..complete item. Sch.no.New

Mild Steel iron work for coloumn& beam……..complete item.sch no.504

First class brick work in 1:4 cement and coarse sand mortar in supper structure………….complete item sch no.307

12 mm plaster 1:3 cement and c.sand mortar..complete item sch no.583

supply and filling of 80 mm thick interlocking Rubber moulded tiles….complete item.S.I NEW Item.

Supply and fixing of 25 mm dia &600 mm long bolt with nut ………complete item( as per market rate)

Supply and fixing of steel plate with steel nut …complete item ( as per market rate)

Steel Polish with primer & side cleaning complete item

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels,plates etc., including welding, grinding, buffing,polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners ,stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suityable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts,bolts, fasteners etc.). DSR NO.10.28.1(attached DSR Copy)

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 1.00mm thick with zinc coating not less than 275gm/sqm..... D.S.R. No. 12.1.1.

Cost of crain charges….complete item.DSR NO-0028

Cost of Loader charges….complete item.DSR NO-0018

Retro- Reflective Sheeting type -XI with 4mm thick ACM Single Side Providing & fixing of reflective sings with a corrosion resistant 4mm thick with 0.4 to 0.5 mm both side aluminium skin aluminium composite panel face to be fully covered with high intensity prismatic sheeting type IV as per IRC- 67:2012 retro reflective sheeting with back frame MS angle of 35x35x5mm Legendes, letters, numerals and boders etc should be as per MORTH specification No-801.3.7 the sheeting shall have a pressure - sensitive adhesive of the aggressive- tack type requiring no heat solvent other preparation for adhesion to a smooth clean surface, in a manner recommended by the sheeting manufacture. The ACM (Aluminium Composite Materials) shall be fixed on the back fram MS Angle with riveting. Micro prismatic type IV Retro- reflective sheeting confirming to ASTM D4956-09 shall be pressure fixed. The Ratro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these test shall be obtained from International/ Government laboratory / Institute by the manufacturer of the sheeting and in case the certificate is obtained from International condition, it should also be obtained from Indian condition with in 3 years of launching of product by the manufacture in abroad. Alternatively a certificate conforming to ASTM Specification (04956-09) uploaded which quoting tender. the rate shall include all materials, labour, T&P, transportation, installation and incidentals all complete as per direction of the Engineer - in - Charge

Supply & Fixing of Sign. Board.