Uttar Pradesh Rural Road Development Agency Tender

Providing and fixing of reflective typical PMGSY logo and informatory sign board with a corrosion resitant 3mm and 4mm thick aluminum composite panel face to be fully covered with DM 5600 engineering grade prismatic / equvivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle

Providing and fixing of Logo sign board at starting point & Intermediate distance with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle

Analysis of Panel concrete Pavement Construction of Panel concrete plain Cement concrete pavement, Thickness as per design, over a prepared subbasewith 43 grade cement or any other type as per Clause 1501.2.2 M 30 (Grade) coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate no exceeding 25mm, mixed in a concrete mixer of not less that 0.2 cum capacity and appropriate weigh batcher uusing approved mix design , laid in approved fixed side formwork ( Steel Channel, Laying and fixing of 125 micron thiock polythene film , wedges, steel plates including levelling th formwork as per Drawing ), Spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and fininshedin continous operation including provision of contraction and expansion, construction joints , applying debonding strips, primer, sealant , dowel bars, near approaches to bridge/culvert and construction joints, admixture as approved, curing of concrete slabs for 14 days. curing compound ( Where specified ) and water finishing to lines and grade as per drawing and Technical specification Clause 1501. PCc Grade M-30 Each Panesl ( 0.50 X0.50 ) thickness 125mm

Providing and fixing of Maintenance information sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle

Providing and fixing of semi reflective curvature board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads and approved drawing Clause 1701.2.2. (0.27 sqm area)

Providing and fixing of semi reflective Village Sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads and approved drawing Clause 1701.2.2. (0.27 sqm area)

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. Ordinary Kilometer Stone (Precast)

Reinforced cement concrete M15 grade hectometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. 200 m Stone (Precast)

Providing & laying of Interlocking Concrete Block pavements Rubber Moulded Reflective Zig-Zag 80 mm thick tiles of precost compressed C.C.l passing minimum 30 megapascle compressive strength I.S.I. Marked. In Gray Base. as per PWD Sultanpur SOR, drawings and techinical Specification Clause 1504 (Laid over previously prepared subbase/base excluding cost of GSB/G-2).

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of side

Providing concrete for plain/reinforced concrete M10 (1:3:6) in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Brick masonry work in cement mortar in substructure complete excepting pointing and plastering, as per drawing and technical specification Clauses 602, 603, 604, 1202 & 1204 (1:4)

Providing and laying reinforced cement concrete 1000mm dia pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry (1X1000)

Pointing with cement mortar (1:3) on brickwork as per drawing and technical specification Clauses 613.3 and 1204

Construction of Embankment with approved soil with a lift upto 1.5 m laying in layers, breaking clods, dressing to required lines, curves, grade and sections, watering and compaction to meet requirement of table 300.1 and 300.2

Plastering with cement mortar (1:4), 15mm thick on brickwork in substructure as per technical specification

Painting two coats including prime coat with epoxy paint of approved brand on concrete/steel surfaces after through cleaning of surface to give an even shade as per drawing and Technical Specification Clause 1701

Brick masonry work in 1:3 cement mortar in substructure complete except pointing and plastering, as per drawing and technical specification MORD 602, 603, 604, 900, 1202 & 1204

P.C.C grade M-20 (1:1.5:3) nominal mix Providing concrete for plain/reinforced cement concrete in substructure complete as per drawings and technical specification. MORD 802, 804, 805, 806, 807, 900, 1202 & 1204

Laying Cement Concrete 450mm dia Pipe NP3 (burried conduits) on first class bedding of granular material in single row including fixing collar with cement sand mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonary work in head wall and parapet

Renewal (Part 3)

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. (Local Earth)

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. (Carted)

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.75 kg/sqm using mechanical means as per Technical Specification Clause 502 Pot hole area (area as per part-1 item no.-2) = 467.44/0.075=6232.50sqm.

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.275 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing and laying bituminous cold mix (30mm. thick bituminous concrete) on prepared base consisting of a mixture of unheated mineral aggregate and emulsified with CRRI or IIT approved emulsion for BC layer cold mix including mixing in a plant of suitable type and capacity, transporating, laying, compacting and finishing to specified grades and levels.

Road marking with hot applied thermoplastic compound with reflectorising glass beads on bituminous surface. Providing and laying hot applied thermoplastic compound 2.5mm. Thick including reflectorising glass beads @ 250gms./sqm. Area thickness of 2.5mm. is exclusive of surface applied glass beads as per IRC 35-2015 the finished surface to be level, uniform and free from streeks and holes. Add 5% for Junction, curves, zebra crossing etc.

Road marking with hot applied thermoplastic compound with reflectorising glass beads on bituminous surface. (Repeated/tranvers bar) Providing and laying hot applied thermoplastic compound 5.00mm. Thick including reflectorising glass beads @ 500gms./sqm. Area thickness of 5mm. is exclusive of surface applied glass beads as per IRC 35-2015 the finished surface to be level, uniform and free from streeks and holes. For Repeated Bar Marking (Yellow colour) Across full carriage way (Strips of 300mm wide & 5mm high and 600mm apart) (Area=1x6x3.75x0.30 =6.75sqm)