Uttar Pradesh Rural Road Development Agency Tender

Moorm Filling in hard Shoulders befor consoladation inculiding cost of moorum having CBR . Bspreading in layers bringing to appropriate moisture content and compacting to specification requirement in proper camber and grade as per MORD Specification clause 305 and its subclauses where required including conssolidating the original grond by rolling as directed by Exgineer In Charge with 8-10 tonnes roller MORD Specification no 407 B SI no 4.10 (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1. (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with a lift upto 1.5 m and lead upto 1000 m as per Technical Specification Clause 302.3 (GSB Trench) (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Scrapping of existing painted surface and making surface clean and levelled for upper layers as per direction of Engineer-In-Charge. A) Area with painted surface in 60% ok Condition. (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Providing ,Laying spreading & compacting stone aggregate of specific sizes to water bound macadam specification including spreading in uniform thickness, handpacking,rolling with smooth wheel roller 80 - 100 KN in stages to proper grade and camber,applying & brooming,screening/binding materials to fill up the intersices of coarse aggrgate,watering & compacting to the required density grading 2 as per Technical Specification Clause 405. Grading -II material (63-45 mm size) with screening material Type "B" (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Providing ,Laying spreading & compacting stone aggregate of specific sizes in 75 mm layer thickness to water bound macadam specification including spreading in uniform thickness, hand packing,rolling with smooth wheel roller 80 - 100 KN in stages to proper grade and camber,applying & brooming, screening materials to fill up the intersices of coarse aggrgate,watering & compacting to the required density as per Technical Specification Clause 405 of MORD. Grading -III material (22.4-53 mm size) with screening material Type "B" (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Pre-coating of chips with 1 per cent of paving bitumen by weight of chips in a suitable mixer duly heated to 160 degree C as per Technical Specification Clause 507.2.5 (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Providing & applying primer coat with SS Emulson on prepared surface of granulat base including cleaning of road surface and spraying primer at the rate of 0.7 - 1.0 kg/sqm using mechanical means as per Technical Specification class 502. (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Surface Dressing (Case-1) 19mm nominal chipping size Providing and laying surface dressing as wearing course in single coat using precoated crushed stone aggregates of specified size on a layer of bituminous binder laid on prepared surface and rolling with 8-10 tonne smooth wheeled steel roller with hydralic self propelled chip spreader etc. (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Surface Dressing (Case-2) 13.2mm nominal chipping size Providing and laying surface dressing as wearing course in single coat using precoated crushed stone aggregates of specified size on a layer of bituminous binder laid on prepared surface and rolling with 8-10 tonne smooth wheeled steel roller with hydralic self propelled chip spreader etc. (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Brick edging labour rate only on both side of the 1st class brick 8 cm. (3") wide and 12 cm. (4 1/2) deep laid with mud mortor all labour finished to the required template and in proper alignment and also including dressing and remming the excavated earthe as directed by Engineer-In-Charge. (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Brick soling with straight over burnt bricks laid on edge i/c prepared sub-grade with brick on end edging according to lines, graded and cross-section shown on the drawing filling joints with sand and earth, spreading blinding coat of i cm depth of local earth or sand over the entire surface &i/c T&P labour etc. (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Construction of Panel plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M 30 (Grade), coarse and fine aggregate not xeceeding 25 mm, mixed in concrete mixer of not less than 0.2 cum capcaity and appropriate weight batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel paltes including levelling the formwork as per drawing) spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including porovision of contraction and expansion, construction joints applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501.PCC Grade M-30 Each Panel(0.50x0.50) thickness 125mm) (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Providing and Laying of Interlocking Concrete Block Pavements having thickness 100 mm and Grade of M-30 as per drawings and Technical Specification Clause 1504. as per direction of Eng-in-charge.Including all taxes & GST if any etc (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Earthwork in excavation for structures as per drawing & technical specifications clause 305.1 including setting out, construction of shoring & bracing ,removal of stumps & other deleterious matter and disposal upto a lead of 50 m & height upto 3m, dressing of sides & bottom, backfilling in trenches with excavated suitable material with dewatering (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Concrete foundation with 40 mm gauge Stone Ballast with approved coarse sand and cement in proportion of 1:3:6 including all materials,labour T&P etc complete as materials,labour T&P etc complete as (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Brick Masonary work in 1:3 (1 cement 43 grade : 3 coarse sand) in sub-structure & Super structure complete excluding pointing & plastering as per drawing & technical specifications. (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Plastering with cement mortar (1:4), (1 cement 43 grade : 4 coarse sand) 15 mm thick on brickwork in substructure as per technical specification Clauses 613.4 & 1204 (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Plain/reinforced cement concrete in 1:2.5:5 (1 Cement:2.5 Coarse sand:5 Stone Grit) substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (CC Copping) (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Pointing with cement mortar (1:3) on brickwork as per drawing and technical specification Clauses 613.3 and 1204 (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Sand filling in the sides of pipes for hume pipe culvert including all material labour, watering etc. completed. (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Supply & Laying of NP-3 Hume Pipe & Collar 450mm dia (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Supply & Laying of NP-3 Hume Pipe & Collar 600mm dia (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Painting two coats including prime coat with epoxy paint of approved brand on concrete/steel surfaces after through cleaning of surface to give an even shade as per drawing and Technical Specification Clause 1701 (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Two coat white washing as per so Aligarh circle (chapter 16 item no 672) (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia C pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Dewatering of water loged area i/c pump operator,fuel etc. (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

PMGSY Informatory Board (Main) with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Nagrik Suchana Bard with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Maintenance Board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Direction Sign Boards with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (including Caution Bard) (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Village Name Sign Board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Kilometer Stones (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

5th Kilometer Stones (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Hectometer Stones (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

PMGSY Logo Board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Construction of Typical Reference piller as per drawing 200.2 complete with white washing, lettering and painting etc. As per drawing. (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Construction of Typical Bench Mark as per drawing 200.2 complete with white washing, lettering and painting etc .As per drawing. (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Providing & laying hot applied thermo plastic compound 2.5mm thick including refletrorising glass beads @ 250 gm/Sqm, Area, thickness of 2.5mm is exclusive of surface applied glass beads as per I.R.C. 35. The finish surface to be level, uniform and free from streaks and holes. Composition of thermo plastic material shall be as per table 800-3 of clause 803 of MORTH including cost of all material, labour, T&P etc., required for proper completion of work as direction by Engineer-In-Charge. (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Providing and fixing of Mandatory / Regulatory sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (TRIANGLE 600 MM) (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Providing and fixing of Mandatory / Regulatory sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (STOP 750 MM) (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Providing and fixing of Mandatory / Regulatory sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (CIRCLE 600 MM) (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Providing and fixing of Mandatory / Regulatory sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (HAZARD 300X900 MM) (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)

Providing and fixing of Mandatory / Regulatory sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (CHEVERON 500X600 MM) (Including royalty, labour cess and others applicable levies & all taxes complete excluding GST)