Uttar Pradesh Rural Road Development Agency Tender

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per MoRD Technical Specification Clause 405. Including all taxes, Royalty etc but excluding GST.

Construction of Panel concrete plain Cement concrete pavement, Thickness as per design, over a prepared subbasewith 43 grade cement or any other type as per Clause 1501.2.2 M 30 (Grade) coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate no exceeding 25mm, mixed in a concrete mixer of not less that 0.2 cum capacity and appropriate weigh batcher uusing approved mix design , laid in approved fixed side formwork ( Steel Channel, Laying and fixing of 125 micron thiock polythene film , wedges, steel plates including levelling th formwork as per Drawing ), Spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and fininshedin continous operation including provision of contraction and expansion, construction joints , applying debonding strips, primer, sealant , near approaches to bridge/culvert and construction joints, admixture as approved, curing of concrete slabs for 14 days. curing compound ( Where specified ) and water finishing to lines and grade as per drawing & PCC Grade M-30 Each Panesl ( 0.50 X0.50 ) thickness 125mm. as per MoRD Technical specification Clause 1501. Including all taxes, Royalty etc but excluding GST.

Providing and Laying of Interlocking Concrete Block Pavements having thickness 100 mm as per drawings and as per MoRD Technical Specification Clause 1504. Including all taxes, Royalty etc but excluding GST.

Road Informatory Sign board with PMGSY LOGO of specified size as per drawing & MoRD Technical Specification Clause Cl.1701. Including all taxes, Royalty etc but excluding GST.

Supply & fixing of "Nagarik Suchana Board" with logo as per drawing attached including lettering, painting in appropriate sizes & MoRD Technical Specification Clause Cl.1701. Including all taxes, Royalty etc but excluding GST.

Supply & fixing of "Maintenance Board" with logo as per drawing attached including lettering, painting in appropriate sizes & MoRD Technical Specification Clause Cl.1701. Including all taxes, Royalty etc but excluding GST.

Direction/village name and Logo sign board of 0.90 sqm as per drawing & MoRD Technical Specification Clause Cl.1701 .Including all taxes, Royalty etc but excluding GST.

RCC M-15 grade Kilo meter Stone 1110 x350 x250 mm top in semi circle painted in orange colour as per Direction of Engineer-in-charge.Including all taxes, Royalty etc but excluding GST.

RCC M-15 grade 5th Kilo meter Stone as per PMGSY specification & as per Direction of Engineer-in-charge.Including all taxes, Royalty etc but excluding GST.

RCC M15 grade Hecto meter stone 1110 x150x150 mm as per Direction of Engineer-in-charge.Including all taxes, Royalty etc but excluding GST.

PMGSY Logo sign board of 0.90 sqm as per drawing & MoRD Technical Specification Clause Cl.1701. Including all taxes, Royalty etc but excluding GST.

Providing and fixing of Mandatory / Regulatory sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (TRIANGLE 600 MM) as per Direction of Engineer-in-charge.Including all taxes, Royalty etc but excluding GST.

Providing and fixing of Mandatory / Regulatory sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (STOP 750 MM) as per Direction of Engineer-in-charge.Including all taxes, Royalty etc but excluding GST.

Providing and fixing of Mandatory / Regulatory sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (CIRCLE 600 MM) as per Direction of Engineer-in-charge.Including all taxes, Royalty etc but excluding GST.

Providing and fixing of Mandatory / Regulatory sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle (HAZARD 300X900 MM) as per Direction of Engineer-in-charge.Including all taxes, Royalty etc but excluding GST.

CD Drain Retaining wall

Excavation in Soil with Dozer with lead upto 100m Excavation for roadway in soil by machanical means including cutting and pushing the earth to site of embankment upto a distamce of 100m, including trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections.as per MoRD Technical Specification Clauses 302. Including all taxes, Royalty etc but excluding GST.

Providing and laying cement concrete in 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and curing complete, lncluding cost of form work. in Foundation and floors.Ch-5, S.I No. 4.1 SOR on 01-08-2023. Including all taxes, Royalty etc but excluding GST.

Class- 150 (Non Modulao brick work in 1 :4 cement and Coarse sand mortar in foundation and plinth including supply of all materials, labour and T&P etc. required for proper completion of the work Ch-6 S.I. No. 6.1.1 SOR on 01-08-2023. Including all taxes, Royalty etc but excluding GST.

Providing and laying reinforced cement concrete in superstructure as per drawing and MoRD Technical Specifications Clauses 800, 1200. Including all taxes, Royalty etc but excluding GST.(M-20 1:1.5:3)

Supplying, fitting and placing HYSD bar reinforcement in super-structure complete as per drawing and MoRTH Technical Specifications.Including all taxes, Royalty etc but excluding GST

Pointing with cement mortar (1:3) on brickwork as per drawing and MoRD Technical Specification Clauses 613.3 and 1204. Including all taxes, Royalty etc but excluding GST.

Plastering with cement mortar (1:4), 12 mm thick on brickwork in substructure as per MoRD Technical Specification Clauses 613.4 & 1204. Including all taxes, Royalty etc but excluding GST.

White washing with lime on undeco rated wall surface (one coat) to give an even shade including thoroughly brooming the surface to remove all dirt, dust mortar drop and loose scales of lime wash and other foreign matter' Ch-16 S.I. No. 13.38 SOR on 01-08-2023. Including all taxes, Royalty etc but excluding GST.

Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and MoRD Technical Specification Clause 1701. Including all taxes, Royalty etc but excluding GST.

Printing New Letters and Figures of any Shade with synthetic enmel paint block or any other approved colour to give an even shade as per drawings and MoRD Technical Specification Clause 1701. Including all taxes, Royalty etc but excluding GST.

Renewal (Part 2)

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per MoRD Technical Specification Clause 303.1.Including all taxes, Royalty etc but excluding GST.

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70 -1.00 kg/sqm using mechanical means as per MoRD Technical Specification Clause 502. Including all taxes, Royalty etc but excluding GST.

Providing and applying tack coat with Bitumen Emulsion (RS-1) using emulsion distributor at the rate of 0.25 - 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per MoRD Technical Specification Clause 503.Including all taxes, Royalty etc but excluding GST.

Bituminous Concrete Using Waste Plastic Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.40 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH Specification Clause No. 507 complete in all respects (Grading-II). Including all taxes, Royalty etc but excluding GST.

Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Providing and laying Road Marking with hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes. As per IRC 35-2015 & MoRTH Specification Clause No. 803. Including all taxes, Royalty etc but excluding GST.