Uttar Pradesh Rural Road Development Agency Tender

Plain Cement Concrete M-10 (1:3:6 nominal mix) in foundation upto a depth of 1.5 m below ground level, including cost of all materials, labour and T&P etc as per drawings & Technical Specification Clause 1109

Providing concrete M-20 for plain / reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Brick Masonry work in cement mortar (1:3, 1 cement : 3 coarse sand) in foundation complete excluding pointing and plastering as per drawing and technical Specification Clause 600, 1202 & 1203.

Plastering with cement mortar (1:4), 15 mm thick on brickwork in substructure as per technical specification Clauses 613.4 & 1204

Providing and fixing of Logo sign board at starting point & Intermediate distance with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle

Providing and fixing of reflective typical PMGSY logo and informatory sign board with a corrosion resitant 3mm and 4mm thick aluminum composite panel face to be fully covered with DM 5600 engineering grade prismatic / equvivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle

Providing and fixing of reflective Citizen information sign board with a corrosion resitant 4mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle

Providing and fixing of Mandatory / Regulatory sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle 600 mm Triangle

Providing and fixing of Mandatory / Regulatory sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle Octogonal 750 mm

Providing and fixing of Mandatory / Regulatory sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle Circle 600 mm

Providing and fixing of Mandatory / Regulatory sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle Cheveron single 500 x 600 mm

Supply & Fixing of Retro reflective Tree Plate having size 15cm x15cm, consisting Type XI Retro reflective Shelling fixed. Over 1.50 mm thick aluminum sheet including labour, Material T&P etc for proper completion of the work. The rate shall include all materials, labour, T&P, transportation, installation and incidentals all complete as par direction of the Engineer-in-Charge

Delineator: Supply & Fixing of MS Delineator made of Mild steel with pure polyester powder coating will the minimum thickness of powder coaling of not less than 40 micron for protection against corrosion The surface should be encouraged so that there should not be any exposed surface without powder coaling Altimatively, these metal guide poles can be concealed with thermoplastic body. The posis shall have tan ellipsoidal or circular design with the height of the pole shall be 800 to 900 mm above the ground with about 200 to 300 mm base which can be anchored onto the ground. Mild steal Guide Pales shall conform to Type XI sheeting specifications as per IRC:67 and ASTIA 04950 which would ensure to obtain clear visibility of the road alignment during right time The Retro reflective sheeting shall be tested for A certificate of having the slice ting tested for coefficient of retro reflection, daytime colour and Tuminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, secular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International Government Laboratory/Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (04955-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally, in such a situation, the Employer/Client, if so desires, could sock for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67.2012 & Proof of the same Report shall be uploaded which quibbling tender. The rate shall include at materials, above, TAP. Transportation, installation and incidentals as complete as per direction of the Engineer-in-Charge

Providing and erecting a "W" metal beam brash barrier comprising of 3 mm thick corrugated sheet metal beam rail 70 cm above road/ground level fixed on ISMC series chennal vetical post 150x75x5 mm spaced 2 meter center to center 1.8 meter high 1.1m below ground/road level at steal parts and fitments to be galvanised by hot dip process. All fitting to conform to IS 1357 & IS 1364 metal beam rail to be fixexd on the vertical post with special of channel section 150x75x5 mm, 330 mm long complete as per cluase 810.

Providing and fixing of Maintenance information sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle

Providing and fixing of Mandatory / Regulatory sign board with a corrosion resitant 3mm thick aluminum composite panel (ACP) face to be fully covered with DM 5600 engineering grade prismatic/equivalent sheeting Type I as per IRC67:2012 with post of MS structure of square hollow section MS 75X75X6 mm and MS frame of 35X35X5 mm angle.600 mm x 450 mm rectangular

Renewal (Part 3)

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.40 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORT&H specification clause No. 507 complete in all respects

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.

Providing and laying of hot applied thermoplastic compound 5 mm thick including reflectorising glass beads @ 500 gms per sqm area, thickness of 5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703. 200 m. Hectometre Stone (precast)

White washing two coats on parapet walls including preparation of surface as per Technical Specification Clause 1915

Painting two coats including primer coat after filling the surface with synthetic enamel paint in all shades on new, plastered / concrete surfaces as per drawing and Technical Specification Clause 1701

Repainting and relettering of ordinary KM stones as per IRC design (except 5th km stone) with approved enemal paint of superior quality including supply of all materials, labour and T & P etc. required for proper completion of the work

Repainting and relettering of 5th KM stones as per IRC design (except 5th km stone) with approved enemal paint of superior quality including supply of all materials, labour and T & P etc. required for proper completion of the work

Printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade as per drawings and Technical Specification Clause 1701