Uttar Pradesh Projects Corporation Limited Tender

Antitermite Treatment

R.C.C. M-20 Grade work in plinth & lintel beam

R.C.C. M-20 Grade work in slab

First class brick work in 1:4 cement and coarse sand of 2.25 fineness modulus) mortar in foundation

First class brick work in 1:4 cement and coarse sand of 2.25 fineness modulus) mortar in super structure for wall thickness 230 mm.

First class brick work in 1:4 cement and coarse sand of 2.25 fineness modulus) mortar in super structure for wall thickness 115 mm.

P/F reinforcement in R.C.C. work

Providing and laying "brick coba" 12mm thick laid with M.150 class brick bat coba 7.50cm. Thick with gap of 15mm to each other. over 20mm. Thick base of cement morter 1:4 cement and coarse sand mixed with water proo fing compound spreading cement slurry mixed with aerelic cement concrete waterproofing compound filed gaps of coba & top of coba mortar mixed with water proofing compoond. in 1:4 cement & coarse & morter finished smooth & top mashed false square 30cmX30cm. & side wall parapet shall be mono tythic plaster wall up to 30cm higher & junction corner shall be rounded by brick ballast & cement and coarse sand masonary coba with top finished mixed with acetic water proofing compound @ 2% by weight & including S/o all material, labour, T & P etc. com.for proper completion of work

12 mm plinth plaster in 1 cement : 5 coarse sand mortar

12 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. 1 cement : 6 Coarse sand mortar

12mm cement plaster in single coat on fair side of single or half brick wall for exterior plastering up to floor two level including internal rounded angles chamfers, and/or rounded angles not exceeding 80mm in girth and finished even and smooth no extra for mixing any additive. 1 cement : 6 Coarse sand mortar

Forming groove of uniform size from 12x12 mm and upto 25x15 mm in the top layer of washed stone grit plastered surface as per approved pattern, including providing and fixing aluminum channels of appropriate size and thickness (not less than 2 mm), nailed to the under layer with rust proof screws and nails and finishing the groove complete as per specifications and direction of the Engineer-in- Charge..

P/L Vitrified floor tile in different sizes ( thickness to be specified by the manufacturer) with water absorption's less than 0.08% & conforming to is:15622 of approved in all colours & shades laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand including grouting the joints with white cement & matching pigments etc complete as per dsr 11.41.2 size of tile 600*600 mm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.on counter slab

Supply and fixing of ceramic tiles in toilet flooring and skirting complete

Making 450 mm wide Plinth protection/ C.C. apron complete

Making Wardrobe/Cabinate under and upon the counter slab as per drawing made with 18 mm thick pre leminated wooden partical board complete with all required fittings etc.

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm ) , with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (±0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer in-charge Extruded section profile size 42x50 mm

Providing and fixing to existing door frames 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered singleCode Description Unit Rate No. SUB HEAD : 9.0 WOOD AND P.V.C. WORK 163 panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter).

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 32 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Distempering (Two coat) with oil bound distemper including cost ofall materials. (For Ceiling & Internal wall surface)

Finishing walls with Premium Acrylic Smooth exterior paint (Apex) in 2 coats

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge Glass Reinforced Gypsum (GRG) board conforming to IS: 2095- (Part 3) : 1996 (Board with BIS certification marks)

Providing & fixing of Center lock in Main door shutter complete.

Painting two coat over priming coat (but including cost of priming coat) on steel and other metal surfaces including cost of all materials, labour T & P etc. required for proper completion of the work.

Providing & fixing glass panes with putty and glazing clips in windows & ventilator all complete with : 4.0 mm thick glass panes

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :Second class teak wood

Making Brainding on outr side of new Room as par gideline of NHM

PLUMBING Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with ISI marked white solid plastic seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required.

Providing & fixing white viterous china wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fitting and brackets, cutting & making good the walls wherever required .Flat back Wash Basin size 550x400 mm with single 15mm C. P. brass pillar tap

Providing and fixing white vitreous china laboratory sink with C.I. brackets,C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, includingpainting of fittings and brackets, cutting and making good the wall whereverrequired :and making good the walls wherever required: 450mm x 300mm x 150mm

Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete. 32/40 mm dia (for wash basin & sink)

P/Fixing of S.S. Jali 100 mm dia on trap

Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. Concealed work including cutting chase and making good the wall etc. (a) 20 mm nominal outer dia pipes

Providing and fixing G.I Pipe Complete with GI Fittings and clamp, i/c cutting and making good the walls etc (a) 20mm GI pipes

(b) 25 mm nominal bore

Providing & fixing gun metal gate valve with C.I. wheel of approved quality (screwed end)

25 mm nominal bore

Providing & fixing 15 mm nominal bore 45 cm long unplasticised PVC connection pipe with brass unions.

Providing & fixing 15 mm nominal bore CP brass bib cock of approved quality conforming to IS 8931.

Providing and fixing 15 mm nominal bore C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

Providing & fixing 15 mm nominal bore C.P brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fitting and base support for tank. 500 litres capacity (01 No.)

Providing & fixing of PVC soil, west and vent pipe pipes. (a) 100 mm dia PVC Pipe

(b) 75mm dia PVC Pipe

Providing 450 mm long C. P. brass towel rail complete with C.P. brass brackets

P/L 25 mm thick C.C. 1:2:4

Making Soak Pit

Excavating trenches in all kind of soil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. up to 1.50 m depth Pipes 80 mm to 300 mm diameter

P/Laying and jointing PVC pipe 100 mm dia

Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with precast R.C.C. vertical grating complete as per standard design With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

ELECTRICAL Wiring point for light with 1.5 sq.mm FR P.V.C. insulated multistrand single core Copper Conductor cable in heavy gauge rigid steel conduit pipe partly concealed in wall & partly laid in slab along with the reinforcement before concreting complete with 14 S.W.G copper earth continuity wire & piano type switch etc. complete in all respects.

Same as in item no. 1 but for fan. and light duty exhaust fan

Same as in item no. 1 but for 5 amp plug point with piano type switch & socket etc.

Supply & fixing of power plug with 15 amp 250 volts flush type switch & 3 pin 15 amp 250 volts flush type socket in suitable M.S. box of 175 mm * 100mm * 50 mm size with bakelite sheet cover 3 mm thick fixed with brass machine screws & washers complete in all respect.

Supply & wiring of sub main with FR P.V.C. insulated 1100 volts grade single core copper conductor cable in heavy gauge rigid steel coduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting complete with one no. 14 SWG copper earth continuity wire complete in all respects. 2 x 2.50 sq. mm. In 20 mm dia conduit.

S/F of surface / flush mounting SPN Distribution board without MCB complete in all respects as directed at site by Engineer-in-charge.4 WAYS

Supply & fixing of 6/10/16/20/25/32 amp. SP MCB (10 KA)

S/F 40 Amp 2 Pole MCB Isolator (10 KA)Leygrand Lexic 40 Amp 2 Pole

Supply & fixing of LED TUBE LIGHT with batten suitable for up to 1x22 watt tube light complete including tube etc. complete in all respects.

Supply and Fixing of electronic fan regulator 120-280 V ISI marked, on existing switch board including making connections, required material, labour T&P etc.

S/F of hexagonal fan box with hexagonal side of approx. 80 mm.in length fabricated from 16 SWG M.S. sheet incorporating with 10 mm. dia. Complete for proper completion of work.

Supply and erection of AC 1200mm Sweep, 230/250 Volts, 50 Hz ceilling fan with standar down rod, blades including connection etc. complete as required -Make: Bajaj, Crompton, Oriant

Supply and erection of AC 230/250 volts, 50 HZ exhaust fans including providing nuts, bolts, mounting frame and other accessories etc. complete (Make : Bajaj / Crompton / Oriant) 300 mm sweep 900 rpm

Supply & fixing of Batton holder with 9 watt LED bulb etc. complete in all required.

Supply & fixing of aluminium conductor PVC insulated cable 10 Sqmm x 2 core

Cost of Subnersible Pump 1.00 H.P/ Mono Block Pump i/c Accessories Installed in Existing Boring for Running Water.