Uttar Pradesh Projects Corporation Limited Tender

Supply Installation Testing & Commissioning of exterior rated Architectural Linear LED Wall Grazer luminaire; suitable for facade lighting with extruded aluminium housing, powder-coated finish, PC Lens with symmetric & elliptical distribution & Toughened glass cover with High Impact Resistance strength, Total System wattage not exceeding 60-80W with system lumen output should be more than 3000 lm with all LEDs on. Operating temperature: -20 °C to +50 °C, Average life L70B50: 50000 hours.Luminaire shall be capable of producing dynamic color changing light with 16 million colors as the light fixture should be programmable using 8 bit control DMX512 protocol / Ethernet based control. Luminaire should be complete with dedicated Lens made up of UL/VDE approved PC for each LED, offering beam angle of different types such as narrow, medium, wide or elliptical as per the site requirement. Fixture should have Height 49mm ± 5% including surface mount base width 50 mm ± 5% , length 1000 mm ± 5% with constant locking hinges for simple position control from various angles without special tools. DMX enabler circuit should be inside the Luminaire only. The rated voltage of the Luminaire should be 230Vac, Toughened glass cover with High Impact Resistance strength of IK07.LED should be of RGBW/3000k with 3535 pacakage of Osram/Lumileds/Cree, Built-In Potted IP67 electronic LED driver with APFC,lower THD, Open Circuit Protection, Over Voltage Protection, Surge Voltage Protection of 10kV with externally attached SPD & other safety test as per IS 15885 Part-2/ Sec 13, IEC60598-1. Signal Transmission Cable - High level waterproof IP 67/68 with nylon connector molded with cable is used for carrying DMX signal from DMX Controller to fixture or from one fixture to another fixture without DMX signal loss & noise generation. CRI = 80 for white LED.With 5 Years O&M Make:Havells/Ligman/Erco.

Supply of exterior rated Architectural Linear LED Wall Grazer luminaire; suitable for facade lighting with extruded aluminium housing, powder-coated finish, PC Lens with symmetric & elliptical distribution & Toughened glass cover with High Impact Resistance strength, Total System wattage not exceeding 40-55 W with system lumen output should be more than 2000 lm with all LEDs on. Operating temperature: -20 °C to +50 °C, Average life L70B50: 50000 hours.Luminaire shall be capable of producing dynamic color changing light with 16 million colors as the light fixture should be programmable using 8 bit control DMX512 protocol / Ethernet based control. Luminaire should be complete with dedicated Lens made up of UL/VDE approved PC for each LED, offering beam angle of different types such as narrow, medium, wide or elliptical as per the site requirement. Fixture should have Height 49mm ± 5% including surface mount base width 50 mm ± 5% , length 1000 mm ± 5% with constant locking hinges for simple position control from various angles without special tools. DMX enabler circuit should be inside the Luminaire only. The rated voltage of the Luminaire should be 230Vac, Toughened glass cover with High Impact Resistance strength of IK07.LED should be of RGBW/3000K with 3535 pacakage of Osram/Lumileds/Cree, Built-In Potted IP67 electronic LED driver with APFC,lower THD, Open Circuit Protection, Over Voltage Protection, Surge Voltage Protection of 10kV with externally attached SPD & other safety test as per IS 15885 Part-2/ Sec 13, IEC60598-1. Signal Transmission Cable - High level waterproof IP 67/68 with nylon connector molded with cable is used for carrying DMX signal from DMX Controller to fixture or from one fixture to another fixture without DMX signal loss & noise generation. CRI = 80 for white LED, With 5 Years O&M Make:Havells/Ligman/Erco.

Supply of exterior rated Architectural LED flood lighting luminaire; suitable for facade lighting with Die-cast aluminium housing, powder-coated finish, Clear toughened glass of 4mm thickness, Total System wattage not exceeding 90-120W with system lumen output should be more than 4200 lm with all LEDs on. Luminaire shall be capable of producing dynamic color changing light with RGBW/3000k colors as the light fixture should be programmable using 8 bit control DMX512 protocol / Ethernet based control. Luminaire should be complete with dedicated Lens made up of UL/VDE approved PC for each LED, offering beam angle of different types such as narrow, medium, wide or elliptical as per the site requirement. Fixture should have Height 364 mm±5% including surface mount base width 188 mm±5% , length 390 mm ±5% with constant locking hinges for simple position control from various angles without special tools.Fixture shall be suitable to operate at an ambient temperature range of -30°C to 50°C and complete luminaire shall be IP66 and IK07 rated. LED Life time shall be at least L70B50 @ 50000 burning hours at 50°C. LED should be with ceramic package of make Nichea, Osram, Cree, Lumiled only. DMX enabler circuit should be inside the Luminaire only.. Luminaire shall be complete with integrated BIS IP 66/67 potted driver and capable of operating at line voltage from 90-305 Vac, 50Hz with power factor 0.9. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Luminaire shall be conforming to BIS i.e. IS 10322 (Part 5/Sec 5) and shall be complete with all necessary accessories required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required.With 5 Years O&M Make:Havells/Ligman/Erco.

Supply Installation Testing & Commissioning of 40-50W LED Flood light, suitable for highlighting architectural features, Instant light with low running temperatures, Operating temperature: -20 °C to +50 °C, Average life L70B50: 50000 hours. Lumen output should be of 2500 Lumens with Full RGBW/3000K on. Housing made of Pure polyester powder coated Aluminum die cast housing in White finish with aesthetically designed heat sink for efficient thermal management, sturdiness & excellent corrosion resistant, PMMA Lens with symmetric distribution. Toughened glass cover with High Impact Resistance strength of IK07.LED should be of RGBW/3000K with 3535 pacakage of Osram/Lumileds/Cree, Built-In Potted IP67 electronic LED driver with APFC,lower THD, Open Circuit Protection, Over Voltage Protection, Surge Voltage Protection of 10kV with externally attached SPD & other safety test as per IS 15885 Part-2/ Sec 13, IEC60598-1. Signal Transmission Cable - High level waterproof IP 67/68 with nylon connector molded with cable is used for carrying DMX signal from DMX Controller to fixture or from one fixture to another fixture without DMX signal loss & noise generation. CRI = 80 for white LED, more for better overall performance & long life. With 5 Years O&M Make:Havells/Ligman/Erco.

SITC of DMX Controller for the system including all other accessories required for the running of the system Controller should have Input Power 5-5.5V DC 0.6A and Output Protocol DMX512 with 4 universe, 2 universe should work in Stand Alone Mode and 2 universe should work in live mode with laptop/ tablet / computer. The universe should be expandable from 2 to 4 DMX512 universes. It should be compatible for Programmability with PC, Mac, Tablet, Smartphone by using USB & Ethernet .Dmx controller should have network controllability feature to control the scene remotely through LAN and triggered via UDP packets on port 2430. Its must have Connections Type C USB, XLR3, Ethernet, battery. There should be provision for Memory microSD card. Device should have Intuitive backlit keyboard with 10 presets and also have provision of kepad on device for changing scene manually from device. Device should be capable to work on Extended triggering possibilities (TCA) & also have Smart Upgrade Technology (SUT). It is an IP 20 unit and has an Operating Temperature of 0°C to 50°C. weight should not be more than 120g. OS Requirements for the controller is Mac OS X 10.8-10.12, Windows 7/8/10. Standards should be EC, EMC, ROHS. The controller should have a variety of features including 2048 DMX channels, clock/calendar, iPhone/iPad/Android remote control, Ethernet facilities, dry contact port triggering and multi-zone SD card memory. Network synchronization of one area across hundreds of universes with the possibility of 99 scenes across 5 areas with auto clock triggering for sunrise and sunset and as per the festivals for specific occasions. Device should be equipped with meta; clamp to mount on wall. All Dynamic LED lighting fixtures & controllers shall be of same make to avoid integration, synchronization, and maintenance issues in future. To be provided with IP 66 enclosure if installed in external environment. With 5 Years O&M Make:Havells/Ligman/Erco/Phillips.

SITC of DMX Splitter/Signal Amplifier to boost the Signal, IP 65 rated module to enhance the depleting DMX Signals, should have IP 66/67 rates inbuilt connectors compatible with Luminaires. It should be offered with inbuilt electronic circuit for functioning. No external LED driver needed.

Planning, Designing, Programming of all the light fixtures with integration into controller and making multiple programming in total of 5 different occasion. Synchronizing all fixtures into one.

Electrical Items

Supply installation commissioning of following sizes of power and data cable as mentioned:

3 x 2.5 sqmm Cu unarmored multistrand

4 x 16 sqmm Al armoured

Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth. 16 sqmm

Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc.

4 sqmm

16 sqmm

Supply and fixing of horizontal air termination (roof conductor) of 25mm x 3mm G.I. strip, G.I. clamps on surface complete in all respects

Supply and burring of Safe Earthing Electrode T-19, (Hot Dip Galvanized), Length up to 3000mm, outer Dia 50 mm inner Dia 25 mm, terminal Dia 12mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity

IP-67/68 Junction Box for Fixture connection

Supply, installation, testing and commissioning of cages for protection of light fixtures of suitable size made of MS grade having wire mesh with spacing of 1.5 - 2 inches and sturdy to avoid ohysical damage with base frame being made of thick strip.

Supply, installation, testing and commissioning of PVC Pipe of size 20 mm as per requirement for cable layingand its protection.

Supply, installation, testing and commissioning of PVC Pipe of size 40 mm mm as per requirement for cable layingand its protection.

Supply, installation, testing and commissioning of Electrical panel with Servo Bypass swith on incomer having 63 A MCCB with Surge Protection Device for all phases with minimum 6 No outgoing of 6 A DP MCCB A compartment having two switches for safekeeping the controller and other necessary equipments

Supply, installation, testing and commissioning of Oil Cooled Servo Stabilizer of 30 KVA Three Phase with Enclosure and connection to the main panel. with rating of 180-250 V stabilizong and maintaining a fixed voltage output of 220Volt for the entire system.

GST Extra as applicable