Uttar Pradesh Projects Corporation Limited Tender

Providing & Placing HDPE Floating Jetty with covered cube system with Follwing specification as per direction of Engineer in charge. •Floating Jetty Modules should be made of High Grade High Density Polyethylene whose Melt Flow Rate should be less than 5 g / 10 min @ 190 Degree C and 21.6 kg Load •Floating Jetty Module should be of L: 50 cm, B: 50 cm, H: 40 cm •Weight of the Floating Jetty Module should be 8 kgs - 10 kgs •Load carrying capacity of the Floating Jetty Module should be Minimum 300 kgs/sqm •The shape of the Floating Jetty Module should be male-female interlocking such that the Floating Jetty Modules can interlock by themselves •Each Floating Jetty Module should have a Separate Anti-Skid Top Cover of 15 mm - 20 mm Thickness fitted in the cervix of the main module •The top surface should be fitted inside the side walls of the Floating Jetty Module and it should be bolted in such a way that there is no leakage of water from the point in which bolt is fixed between top and below surface thus making the surface the best Anti Skid surface available worldwide •There should be one more surface below the top surface with a gap in between top surface and surface below to enable expansion contraction of Floating Jetty Module which can also be used for passing of electric cables and water hoses if required •The lug thickness of the Floating Jetty Module should be 20 mm - 22 mm to ensure enough strength to the structure •Floating Solar Float Modules should be made of High-Grade High-Density Polyethylene whose melt flow rate should be less than 5 g / 10 min @ 190 Degree C and 21.6 kg Load •2 Nos. of Floating Solar Float Modules of L: 120 cm, B: 85 cm, H: 20/40 cm (approx.) should be provided. The Floating Solar Float Modules should have sliding groove on the top, the clamping unit should have clips which can be moved in the groove relative to the float body and to hold different heights of solar panels •6 Nos. of Horizontal Supporting Float Modules of L: 85 cm, B: 40 cm, H: 20 cm (approx.) should be provided & 14 Nos. of Vertical Supporting Float Modules of L: 45 cm, B: 40 cm, H: 20 cm (approx.) should be provided

Providing & Placing HDPE Speed Power Boats 5-seater (4+1) with Follwing specification as per direction of Engineer in charge. Passenger Boat should have Roto-moulded Double Skin Hull (Welding is not allowed) •Material of the Hull of Speed Passenger Boat should be Polyethylene (PE) •Length of the Speed Passenger Boat should be between 440 cm to 460 cm •Width of the Speed Passenger Boat should be between 180 cm to 200 cm •Weight of the Speed Passenger Boat (Only Hull) should be maximum 290 kg for ease of handling •Capacity of the Speed Passenger Boat should be minimum 5 persons •OBM: Minimum 40 HP Remote Yamaha/ Tohatsu/ Suzuki / Mercury should be provided with the Speed Passenger Boat •Console should be provided on the Speed Passenger Boat •OBM panel should be provided for fixing OBM on the Speed Passenger Boat •Mooring Ring, Mooring Cleat and Drain Plug should be provided with the Speed Passenger Boat •Speed Passenger Boat should be any IACS Member Type Approved/ Certified (Certificate should be submitted before start to work.)

Providing & Placing SEARCH & RESCUE 6 TO 8 MEN HDPE 25 HP OBM with Follwing specification as per direction of Engineer in charge. Rescue Boat should have Roto-moulded Double Skin Hull (Welding is not allowed) •Material of the Hull of Search & Rescue Boat should be Polyethylene (PE) •Length of the Search & Rescue Boat should be between 380 cm to 410 cm •Width of the Search & Rescue Boat should be between 150 cm to 170 cm •Weight of the Search & Rescue Boat (Only Hull) should be maximum 180 kg for ease of handling •Capacity of the Rescue Boat should be minimum 8 Persons •OBM: Minimum 25 HP Tiller Yamaha/ Tohatsu/ Suzuki / Mercury should be provided with the Search & Rescue Boat •OBM panel should be provided for fixing OBM on the Search & Rescue Boat •Mooring Ring, Mooring Cleat and Drain Plug should be provided with the Search & Rescue Boat •Search & Rescue Boat should be any IACS Member Type Approved/ Certified (Certificate should be submitted before start to work.) Note:-•Test certificate of Melt Flow Rate of Raw Material of HDPE Floating Jetty from CIPET India or any reputed research centers which are acceptable internationally should be submitted along with Technical Bid •Certificate of ‘Speed Passenger Boat 5-Seater (4+1 Men)’ and ‘Search & Rescue Boat 6 to 8 Men with 25 HP OBM’ should be submitted before start to work.