Uttar Pradesh Power Corporation Limited Tender

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.8 mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm , of size 595x595 mm, having perforation of dia. 10 mm with minimum perforated area 18 % with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thick rockwool of 48 kg /cum backing.

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).size of 600x600 mm

Providing ,making & fixing wall panneling as per drawing from seasoned wood of MIRINDI frame of 2.5"X2.5" size placed horizontally and vertically both way @ 2 ' c/c. the frame work fitted in floor with the help of nails ,screw then frame work to be covered with 12 mm thick plywood from the help of fevicol,nails and screw. then making grooves with 6mm MDF Ply with the help of fevicol,nails and screw. The final surface to be finished with 1mm thick laminate and grooves to polished as per design.. as per requirement and direction of Engineer I/C including cost of all material, labour, T & P etc required for proper completion of work.

Providing ,making & fixing full height wooden partitions as per drawing from seasoned wood of MIRINDI frame of 2.5"X2.5" size placed horizontally and vertically both way @ 2 ' c/c. the frame work fitted in floor with the help of nails ,screw then frame work to be covered with 12 mm thick plywood from both side with the help of fevicol,nails and screw. then making grooves with 6mm MDF Ply with the help of fevicol,nails and screw. The final surface to be finished with 1mm thick laminate on both sides and grooves to r polished as per design.. as per requirement and direction of Engineer I/C including cost of all material, labour, T & P etc required for proper completion of work.

Providing ,making & fixing low height wooden partitions as per drawing from seasoned wood of MIRINDI frame of 2.5"X2.5" size placed horizontally and vertically both way @ 2 ' c/c. the frame work fitted in floor with the help of nails ,screw then frame work to be covered with 12 mm thick plywood from both side with the help of fevicol,nails and screw. then making grooves with 6mm MDF Ply with the help of fevicol,nails and screw. The final surface to be finished with 1mm thick laminate on both sides and grooves to r polished as per design.. as per requirement and direction of Engineer I/C including cost of all material, labour, T & P etc required for proper completion of work.

Providing and applying plaster of paris putty of 2 mm thickness over lastered surface to prepare the surface even and smooth complete

Wall painting Two Coat with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.

Spirit Polishing Two or More coats including a coat of wood filler including cost of all materials, labour and T&P etc required for proper completion of the work approved design by E/I.

Providing and fixing glazing With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Removal of old and damaged sunfilm from the glass panes of door and window shutters,including removal of Glue completely and carefully by scraping or by any means including cost of all materials, labour T&P etc. required for proper completion of the work.

Providing labour for proper arrangement of binding file and shifting files and furniture from one place to another place with required labor, T&P for proper completion of work.

Providing & Making & Fixing of Wall Panneling as per drawing frame work to be covered with 12 mm thick plywood from the help of fevicol,nails and screw. then making grooves with 6mm MDF Ply with the help of fevicol,nails and screw. The final surface to be finished with 1mm thick laminate and grooves to polished as per design.. as per requirement and direction of Engineer I/C including cost of all material, labour, T & P etc required for proper completion of work.

Providing and fixing sun-film of Gareware or equivalent make on glass panes of door and window shutters including cost of all materials,labour and T&P etc. required for proper completion of the work.

Providing and fixing in place a full height storage cabinet 450 mm deep made with 19 mm thick ISI marked ply borad, all interior surfaces to finished with pasting of 0.8 mm thick mica and all exterior surfaces to be finshed with pasting of 1 mm thick mica of texture and colour as approved by Engineer in Charge including all labour, T&P, other items like (but not limited to) fevicol, nails screws, higes, sliders,door handles, multipurpose lock of godrej or equivalent rate etc. required for proper completion of works, to be measured interms of front area only.

Providing and fixing in place a full height storage cabinet 450 mm deep made with MS Sheet of 1.2 mm thickness with proper locking arrangment, handle etc required , painting with spray enamel paintingas as approved by E/I. The work includes cost of all labour, material T&P for proper completion of work.

Repairing of old cushioned officer chair at SB Extn building, removing of old damage upholstery then wooden frame repairing and re-polishing, upholstery of new 75 mm thick sleepwell foam 32 denstry on seat and back side of chair using 50 mm thick sleepwell foam 32 denstry, The work includes cost of all labour, material and T&P etc.NSI(Rate approved)

Repairing of of Executive office computer work station cum work table of size-1500x900x750 in diffrent room OF Shakti Bhawan Extn. Building. Top surface finished with approved Quality 1 mm sunmica laminate and intirior faces finished with 10x20 mm thick sprit polish teak wood beading. . one number lockable drawersone lockable cupboard 400mm wide finished with1 mm sunmica laminate .one no lock and one no handle fitted in drawer and cupboard . & back side covered. .The work include cost of all labour,material T&P required for proper completion of work.NSI (Rate approved)

Repairing of revolving chair in 5TH floor rapdrp/it wing with the help of replacement damage hydrolic with new one including cost of all material, Labour T&P Required for proper completion of the work. NSI (Rate approved)

Replacing existing old damage Tile and Fixing New false ceiling with 12mm thick Arm strong soft mineral fibre type ceiling With required hanger Including supply of all materials, labour and T & P etc required for proper completion of work.

Providing & fixing of Excutive office computer work station cum work table of different sizes as per requirment fitted in 12th floor South wing of Shakti Bhawan Extn. Building. The Unit shall be measered by length x breadth of worktop and 0.76 mtr hight. The Entire Above Unit Shall be Fabricatrd with 19 mm Block Board Superior Quality Swastik Made all Extirior surface with approved Quality 1 mm sunmica laminate and intirior faces finished with 10x20 mm thick sprit polish teak wood beading.t.One no drawer nd one flap door fabricated with the help of 19 mm block board Swastik Block board /green or equivalen The cup-board shall have lockable magnet door fabricated with 19mm block board fixed to cup-board with magnet and having in handle The main table rack shall be approved matel handle and necessery m.p lock. all drawrs shall be provided with approved qaulity slider machnism. The foot board shall be also provided in above three peace .The work include cost of all labour,material T&P required for proper completion of work.

Providing & Fixing of High Back Chair, PP Adjustable Arms, Synchro Tilt,Seat Slide, Nylon Base, Gas Lift ,Net Back Fabric Tapestry Modle Hampton-21 & Make Geeken as approved by E/I.

Providing & Fixing of Medium Back Chair, PU Arms, Silver Powder Coat Metal Frame & Base, Gas Lift , Seat & Back Leatherite Tapestry Modle GW-735& Make Geeken as approved by E/I.

Providing & Fixing of Supreme plastic cushion chair Modle -supreme orntae red colour .The work include cost of all labour,material T&P required for proper completion of work.

Repairng of old cushioned single seater Sofa of SB Extn building, removing of old damage cloth and upholstery then wooden frame repairing and re-polishing, upholstery of new 75 mm thick sleepwell foam 32 densty on seat and back side of Sofa using 50 mm thick sleepwell foam 32 density, finished with good qualty cloth of approved design, colour and texure Approved by E/I. The work include cost of all labour,material T&P required for proper completion of work.

Providing & Fixing of Roller Blinds of approved shade as per drawing & specification as approved by the Architect/ Engineer -in-Charge

Repairing of old MS window by replacing old hinges, handle, rubber gasket including welding equipment, cost include all labour, material, T&P required for proper completion of work.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross band and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing double action hydraulic floor spring With brass cover plate minimum 1.25 mm thickness of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.