Uttar Pradesh Housing And Development Board Tender

Supply, Installation, Testing and commissioning of 11 /0.433 KV (Level-1) Copper wound out door type Delta star distribution transformer of following capacity as per latest specification of MVVNL. The rates also including loading, unloading, local carriage and T & P charges etc. Make:- MODERN/TRANSTRON/ELECON (Whose Latest GTP Approved in MVVNL Having Valid CPRI/ERDA Type Test Report)

250 KVA

Supply, installation, testing and commissioning of Outdoor Type,dust and vermin proof weather proof with rain canopy on four sides with locking arrangement, 630A ACB L.T Pannel Fabricated out of 2.0mm thick CRCA sheet steel, painted with powder coated paint of shade as per the direction of Engineer in charge after proper sheet treatment process of sheet steel. All indicating lights shall be LED type and all wiring shall be done from PVC Insulated copper flexible wire. The panel shall be completed in all respect and shall consist of following material. Incomer: 630 A F.P Manual Fixed type A.C.B with Metering (ie Ameter with ASS, Voltmeter with VSS) along with, Phase Indicating Lights, CT,Control MCB etc. -1 Set Panel will have suitable rating (1Amp/Sqmm) of Aluminium Bas bar for Proper Temination of Cables. ( minimum 400 sqmm6 nos ) All bus bars shall be insulated with coloured heat shrinkable PVC sleeved. All bus bar supports shall be non hygroscopic DMC/SMC supports. Make:- ABB/Schneider/Seimens or as Directed by E/I.

Supply, installation, testing and commissioning of main feeder pillar. The Feeder Pillar shall be Fabricated out of 2.0mm thick CRCA Sheet steel duly Painyed with Powder Coated Paint. The Feeder Pillar shall be suitable for Outdoor Installation,dust and vermin proof weather proof with rain canopy on four sides with locking arrangement & shall confirm to Minimum IP:55 degree of protection. The bus bars shall be of aluminium, electrolytic grade only. Maximum design density shall not exceed 1 Amps/Sqmm. All bus bars shall be insulated with coloured heat shrinkable PVC sleeved. All bus bar supports shall be non hygroscopic DMC/SMC supports. The Feeder Pillar shall be completed in all Respect as per Direction of E/I. Only PWD & CPRI Approved Make

Incoming : Two (2) set 500 Amp. TPN HRC Fuse unit

Outgoing : Five (11) set 300 Amp. TPN HRC Fuse unit

Bus Bar : One (1) No. 500 Amp.TPN aluminimum bus bar of suitable length.

Supply, Intallation testing and commissioning of 300A sub Feeder Pillar. The Feeder Pillar shall be fabricated outof 2.0mm thick CRCA sheet steel, painted with Powder coated paint of shade as per the direction of EngineerIn‐Charge after proper sheet treatment process of sheet steel. The Busbar of Panel shall be of High gradeElectrical grade High Conductive Aluminum alloy of appropriate cross section as per rating. The calculation ofcontinuous rating of Bus Bar shall be submitted. The Bus Bar shall be supported by non hygroscopic SMC/DMC Bus Bar supports which shall be mounted on proper interval to ensure bear the jerks of shortCircuit as fault level require. The Fault level of Panel shall be 50kA for 1sec. The Feeder Pillar shall be dust & Vermin Proof ,weather proof , rain canopy all four sides ,locking arrangements with Degree pf Protection IP : 55. The Feeder Pillar shall be completed in all respect and shall consist of following material. Incomer : 300A Kit Kat type Fuse Unit – 3 Set with Neutral Bus Bar Outgoing: Suitable Bus Bar only with Provision to connect atleast 30 Nos. Outgoing Cables . up to 3.5 core 35sqmm size. Only PWD & CPRI Approved Make

Supply, Intallation testing and commissioning of capacitor control panel cubicle pattern, out door type ,sufficiently ventilated, dust and vermin proof weather proof with rain canopy on all four sides with locking arrangements, suitable for 440 V 3 phase 50 Hz AC supply system complete with :-

FOR 250 KVA TRANFORMER

MCCB 160A 4P 36KA TMA [ incomer ]

1 no . spreader 160 A

ext, rotary handle 160 A

1 set indicating lamps

3 nosMCB 6 A 1P 10 KA

3 nos .ON / OFF/ TRIP indicators

MCCB aux. Contact 160 A

1 NO VAF Meter

1 set .CT3160/5A

APFC relay -12 stage

1 set 200A alu. Bus bar

4 nos MCB 63 A 3P10 KA

4 nos cap bank 25 KVAR

4 nos cap duty contactors 30 KVAR Only PWD Approved Make

S/F of lightening arrestor set (3 No.) Suitable for mounting on Steel Supoorts Complete with all material, labour and T & P required for proper completion of work as per direction of E/I.

Construction of Fencing Plinth of Following Sizes in Ist Class Brick Work including plaster and providing flat bricks soiling and pointing the same with 1:2 cement and fine sand mortor over 75mm thick cement concreting in the ratio 1:6:12 in open space of the cage as per Direction of E/I.

6x4x0.23m for Substation

2x3x0.23m for Subfeeder Pillar

Supply of fixing of 2.45M. High cage fabricated with 3.0mm thick expanded metal/wire mesh of equivalent weight fixed on 50x50x6mm angle iron frame having vertical members spaced at 1.0M to 1.25M. and horizontal members spaced at 1.20M the vetical members shall be grouted in ground and horizontal members in the wall to a depth of 300mm with ends folded. The cage shall have 1000x2000mm size single leaf door with locking arrangement having door frame fabricated with 35x35x5mm angle iron and 3mm expanded metal wire mesh of equivalent weight duly fixed with the cage member. The cage shall have nut bolt arrangement for opening the sides by providing tees 45x20cm of angle iron size 50x50x6mm as per direction of E/I. It shall be painted with red oxide primer and synthetic enamelled paint as per direction of E/I. including all materials, labour and T & P for proper completion of work.PWD SOR 2016 SI No. 1142

Supply and burring of Safe Earthing Electrode T-39 ( Hot Dip Galvanized) Length up to 3000mm, outer Dia 76 mm inner 38 mm, terminal Dia 12mm, outer G.I. Pipe of 16 SWG & Inner G.I. Pipe 12 SWG with Hot Dip Galvanization upto 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm Square C.I. Frame with hinged cover & masonry housing.( from Electrode Terminal to switch board, cost of 25 x 3 G.I. Strip will be extra) As per PWD SOR-2018 S.I. No.-725 (D) Make: As approved in U.P. P.W.D., & C.P.R.I. Certified

Construction of plinth for Transformer size 2.0x1.25x1.0 Complete With all materials, labour and T & P required for proper completion of work as per specification drawing and direction of E/I.

Supply of following size of Al. conductor XLPE Insulated, Cores Laid up, PVC Innersheathed, Armoured with Galvanised Al. Strip Extruded PVC Type ST2 Outer Sheathed, 650V/1100 Volt Grade as per IS 7098 (Part I) 1988 With up to date Ammendments. Make:- POLYCAB/ GLOSTER/FINOLEX / HAVELLS/ KEI/ UNIVERSAL

120 Sqmm 3½ core

240 Sqmm 3½ core

Supply and fixing of palm or pin copper tin plated cable socket (lugs) to the cable leads insulating with tape and making connections etc. complete in all respects (as per PWD SOR 2018 SI No. 504 (h), (j) & (m) )

70 Sqmm

120 Sqmm

240 Sqmm

Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouribg of the cable shall be properly connected with the earth as per direction of Engineer-Incharge. as per PWD SOR 2018 S.No. 503 (m), (o ), (r)

70 Sqmm 3½ core

120 Sqmm 3½ core

240 Sqmm 3½ core

Supply of HDPE pipe upto PN-6 working pressure Rating material Grade PE-80 Nominal dia (OD) 110 mm 6.50 mm thickness complete in all respect as per relevants I.S. Technicals specification.

Digging & Refilling of Same Trench Parallel to Road at a depth of 1.5 Mtr. as required & laying charges of cable & different size HDPE Pipe (PN-6 PE 80 Grade) complete with all material, labour and T&P etc. required for proper completion of work as per Direction of E/I.

S/F of cable route marker made of 1:2:4 R.C.C. Block size 1000x400x10 mm grouted with 1:3:6 cement stone grit coarse sand 30cm below G.L. with painting numbering & marking etc. complete with all required material T&P etc. complete in all respects as per direction of E/I.

S/F of danger board (H.T.) size 200x250 mm at suitable height of pole as per direction of E/I.

Construction of brick masonary service chamber with cover in cement mortar (1 cement: 4 coarse sand) R.C.C top slamb with 1:2:4 mix(1 cement:2 coarse sand: 4 graded stone aggregate 20mm, nominal size) foundation concrete in 1:6:12 (1 cement:6 coarse sand and 12 graded stone aggregate 40 mm nominal size) inside blastering 12mm thick with 1:4 cement & Coarse sand) finished with floating coat of neat cement complete inside size 0.45x0.45x0.60m with class 150 Brick.