Public Works Department Tender

Court Rooms for Other Court :Providing and fixing of midback chair from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA,Greenpro Certified Manufacturers .Overall Dimensions of Chair-Seat Height - min 42.5 to max 54.5cm. Height - min85.5 to max 97.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm..seat/back assembly: the seat and back should be made up of 1.2 ±0.1cm. thick hot-pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should be designed with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area back size 47.5 cm. (w) x58.0 cm (h)seat size 47.0 cm. (w) x 48.0 cm. (d) high resilience (hr) polyurethane foam: the hr polyurethane foam should be moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. armrests :the one-piece armrests should be injection moulded from black co-polymer polypropylene. center tilt synchro mechanism: the mechanism should be designed with the following features: • 360° revolving type. • upright-position locking • tilt tension adjustment • seat/back tilting ratio of 1:3. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm.telescopic bellow assemblythe bellow should be 3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly:the pedestal should be injection moulded in black 33% glass-filled nylon-66 and fitted with 5 nos. twin wheel castors. the pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). .twin wheel castors:the twin wheel castors should be injection moulded in black nylon. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Court Rooms for Other Court :Providing and fixing of Table with CPU Hanger from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers and as per approved drawing & design / specification. size shall be 1650 Width x 9000 Depth x 728 Height mm . Top shall be 18 mm thick Pre laminated particle board all work surface edges shall be having duly sealed with 2 mm thick PVC edgebanding. Understructure Modesty Panel 18 mm thick Pre laminated particle board . The Rectangular frame shall be fabricated component in 1.2 mm thick CRCA , Finish : powder Coat( epoxy polyster) . Leg shall be fabricated component in 38 mm x 25 mm 1.2 mm thick MS ERW ATube ,finish powder coat ( epoxy polyster).The plastic cap for cable travel shall be injection moulded polypropylene and leveler glide for shall be nylon 6 & MS bolt. The storage shall be having shell and drawer tray 0.6 mm thick CRCA Finish powder coat (epoxy polyster) plus the drawer front shall be 0.8 mm thick CRCA Finish powder coat (epoxy polyster) plus lock with 10 lever and handle and leveller. The wire management shall be horizontal wire carrier 0.7 mm thick CRCA Finish powder coat (epoxy polyster) and vertical wire carrier 0.8 mm thick CRCA Finish powder coat (epoxy polyster) .The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Court Rooms for Other Court :Providing and fixing of midback chair from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA,Certified Manufacturers. Overall Dimensions of Chair-Seat Height - min 42.5 to max 54.5cm. Height - min85.5 to max 97.5cm.Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm..seat/back assembly: the seat and back should be made up of 1.2 ±0.1cm. thick hot-pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should be designed with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal area back size 47.5 cm. (w) x58.0 cm (h)seat size 47.0 cm. (w) x 48.0 cm. (d) high resilience (hr) polyurethane foam: the hr polyurethane foam should be moulded with density = 45±2 kg/m3 and hardness load 16 ± 2 kgf for 25% compression. armrests :the one-piece armrests should be injection moulded from black co-polymer polypropylene. center tilt synchro mechanism: the mechanism should be designed with the following features: • 360° revolving type. • upright-position locking • tilt tension adjustment • seat/back tilting ratio of 1:3. pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm.telescopic bellow assemblythe bellow should be 3 piece telescopic type and injection moulded in black polypropylene. pedestal assembly:the pedestal should be injection moulded in black 33% glass-filled nylon-66 and fitted with 5 nos. twin wheel castors. the pedestal should be 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). .twin wheel castors:the twin wheel castors should be injection moulded in black nylon. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Court Rooms for Other Court :Providing and fixing of table from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA,GREENGUARD Certified . size shall be 1665 Width mm x 900 Depth mm x 740 Height mm . The top shall be 25 mm thick PLB with 2 mm thick PVC Edge Beading plus the Understructure shall be having C - Frames 1.6 mm thick MS supporting the top . The Legs shall be of dia. 38.1 x 1.6 mm thick MS ERW tube . The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Court Rooms for Other Court :Providing and fixing of small Almirah from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers & shall have an overall size of 765mm(W)x440mm(D)x1270mm(H) with welded construction. It should have the shelf thickness of 0.7mm, Back thickness of 0.8mm and all other components shall be 0.9mm thick. These components are made of CRCA ‘D’grade high yield strength as per IS:513. The storwel Minor should have a Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting (3 nos.) which shall have a Uniformly Distributed Load capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Court Rooms for Other Court :Providing and fixing of 4 Door Book Case from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers & shall have the configuration of 914mm(W)x320mm(D)x1742mm(H). The unique design provides the right rigidity to the Top hinged doors , which shall facilitate easy use. The Book Case shall be made from prime quality CRCA steel with anti rusting treatment. It shall have a Rigid Knock Down Construction. The Top Pannel, Back Pannel and Side Pannel are made from 0.7mm high yield CRCA and other components from 0.8mm CRCA. Each door shall have a 6 Lever Cam Lock with Common Key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. Scissor Mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. Each door should be provided with plastic side end caps as handle which is easy to grip. Each compartment shall have a storage shelf with a UDL capacity of max 80 Kg. The 2 Door Book Case shall have 18mm PLB Top straight edge with PVC lipping. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Court Rooms for Other Court :Providing and fixing of visitor chair the seat and back from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers . should be made up of 1.2-cm. thick hot-pressed plyOverall Dimensions of Chair-Seat Height - 45.0 cm.Height - 84.0 cm.Width-48.0 cm .Depth- 57.0 cm.wood, upholstered with black leather-cloth (pvc coated cloth) and moulded polyurethane foam. the back foam should be designed with contoured lumbar support for extra comfort. back size: 46.0cm.(vv) x 47.0cm.(h) seat size: 46.0cm.(vv) x 46.0cm.(d) .polyurethane foam: the polyurethane foam should be moulded with density = 45 +/-2 kg/m3 and hardness = 20 +/- 2 on hampden machine at 25% compression. understructure assembly: the assembly should be a welded understructure made of m.s. oval tube 3.5cm x 1.5cm x 16bg thk. and black powder coated. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Court Rooms for Other Court :Providing and fixing of bench from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers . Overall Dimensions of Chair-Seat Height - 44.1 cm.Height - 78.5 cm.Width & Depth of Chair as - Width-169.5cm and Depth-63.8 cm.seat shell : the seat shell should be a welded assembly of seat,back and side frame. the seat and back should be made of 0.12±0.013cm thk cr steel sheet with oblong perforations.they should be welded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk hr steel.the welded assembly should be powder coated ( dft 40-60 microns ). the seat has a front water fall edge to provide popliteal clearance for comfortable seating. it also has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. clean and flat surfaces of seat and back aids in easy maintenance. * seat size : 47.8 cm (w) x 44.6 cm (d) * back size : 41.6 cm (w) x 23.0 cm (h) .understructure assembly: understructure assembly consshould be ts of connecting beam and leg assembly made of m.s. e.r.w. oblong tube of size 7.5±0.03cm x 2.5±0.03cm x 0.2±0.016cm thk.the welded structure assembly should be powder coated ( dft 40-60 microns ).the leg assembly should be fitted with shoes and levellers in nylon. the leg structure should be designed with minimal should be a of contact close to ground providing easy access for cleaning purposes. the shoes fitted to leg assembly help in aligning the structure for back to back arrangements. levellers take cshould be of uneven flooring.connecting beam should be fitted with snap locking end cap.lt also aids in side-by-side understructure alignment arm rest assembly: armrest assembly consshould be ts of armrest frame and armrest pad . the armrest frame should be made up of size 3.175±0.05cm x 0.47±0.027cm thk hr steel and it should be powder coated ( dft 40-60 microns ). armrest pad should be injection molded in nylon and should be fitted onto the armrest frame. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Court Rooms for Other Court :providing and fixing of SEAT/BACK FRAME ASSEMBLY from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers. The seat and back should be made of 0.12 ±0.0096 cm thick CR steel perforated sheets which should be welded to a seat/back frame assembly made of of 0 1.9 ±0.02cm x 0.16 ±0.0128 cm thk MS ERW tube. Connecting Strips made of 0.5 ± 0.05 cm thk HR steel should be welded to the structure for assembly with the connecting beam. The assembly should be powder coated ( DFT 40-60 microns SEAT SIZE: 39.0cm. (W) X 41.5cm. (D) (Approx.).BACK SIZE: 39.0cm. (W) X 21.5cm. (H) (Approx.).ARMREST: It should be made up of oblong tube of size 0.35 ±0.024 cm x 0.15 ±0.015 cm x 0.16 ±0.015 cm Thk. & 0 0.15 ±0.02 cm bright bar welded to seat & back frame assembly.CONNECTING BEAM ASSEMBLY: It should be a U-shaped fabricated assembly made of 0 3.81±0.03 cm. x 0.2 ±0.016 cm thk MS ERW twin tubes. The connecting tubes should be welded together with MS base plates made of 0.25 ±0.025 cm thick CR. Steel and mounting plate made of 0.5 ± 0.05 cm thk HR Steel. Threaded inserts should be provided on both ends of each connecting tube for fixing leg assembly on each side. The connecting beam assembly should be powder coated ( DFT 40-60 microns }.LEG ASSEMBLY: It should be a 2-piece fabricated to form a box section made of 0.16 ±0.0128 cm thk. CR steel. Threaded nuts should be welded to the box section for fixing adjustable glide screws. The leg assembly should be powder coated ( DFT 40-60 microns ).ADJUSTABLE GLIDE: The adjustable glide should be injection moulded in black Nylon 6 and should be used for level adjustment of the beam seating on uneven floor surface. It should be fitted to the leg assembly. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Court Rooms for Other Court :Providing and fixing of stool from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers. Overall dimensions of stool are: Width- 47.3 cm, Depth- 47.3cm, Seat Height-46.5cmseat assembly: li should be circular type 0 30.0±0.5cm and made up of 0.1±0.012cm thk cr steel. it should be welded to the understructure and black powder coated ( dft 40-60 microns )understructure assembly: the understructure should be made of ms tube 0 2.2±0.03cm x 0.16±0.0128cm thk ms erw tube. it should be welded to the ms fabricated circular seat assembly and black powder coated ( dft 40-60 microns ). the understructure should be provided with black pp injection moulded ferrules. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Other P.O. Chambers : Providing and fixing of The Main table from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers & shall be of size 1800 Width mm x 900 mm Depth x 750 mm height. Top surface of the table shall made up of MDF (Medium density fibre ) board duly finished with Veneer and final coating of PU. The Main desk should contain in built key board pull out tray for keeping keyboard of computer. The front modesty panel of the table shall be made up of MDF board of size 1640 mm x 600 mm x 16mm which shall also be duly finished with Veener and PU coating. For personal storage one mobile pedestal (3 drawer unit) shall be provided of size 510 mm Width x 635 mm Height and 445 mm Depth. The storage pedestal shall also be made up of MDF duly finished with veener & final coating of PU. The Side shall be of size 1200mm Width x 445mm Depth x 660 mm Height. The side unit shall be made up of MDF board duly finshed with Veneer and final finish by PU Coating. The design of the side unit shall be such that it can be placed on either side of the main table. The side unit shall contain open space for keeping cpu in extreme right side, one closed storage shutter at extreme left end & open space in the middle with one shelf for keeping files. The thickness of the top of the side unit shall be 25mm. The Size of the Back unit shall be 2215mm width x 410 mm Depth x 2000mm height. The back unit shall be made up of MDF board duly finished with veneer & final finish by PU coating. Below storage shall be provided with wooden shutters & the upper left & right side of the back unit shall also be provided with wooden shutters. The middle 3 door shutters should be of glass of minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H .The Size of the Back unit shall be 2215mm width x 410 mm Depth x 2000mm height. The back unit shall be made up of MDF board duly finished with veneer & final finish by PU coating. Below storage shall be provided with wooden shutters & the upper left & right side of the back unit shall also be provided with wooden shutters. The middle 3 door shutters should be of glass of minimum 5mm thick for display purpose. The hardness of the PU coating shall be 1.5H. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Other P.O. Chambers :Providing and fixing of highback chair SEAT ASSEMBLY from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers : The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. *Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D) .BACK ASSEMBLY: The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette. BACK SIZE: 47.7 cm. (W) x 76.4 cm. (D) . ARMRESTS : The armrest top should be moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W tube having chrome plated finish.The armrest height adjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-SYNCHRO MECHANISM : The adjustable tilting mechanism should be designed with the following features: • 360' revolving type. • Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • Tilt tension adjustment can be operated in seating position. • 5-position Tilt limiter giving option of variable tilt angle to the chair. • Seat/back tilting ratio of 1: 2 • The mechanism housing should be made up of HPDC Aluminium black powder coated. SEAT DEPTH ADJUSTMENT : Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT: The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. PEDESTAL ASSEMBLY: The pedestal should be High Pressure Die cast polished Aluminium and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With castors.) TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Other P.O. Chambers :Providing and fixing of Recliner from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers . Total Length830.Total Height1000.Total Width740 stitching:thread :nylon 40 tkt pitch: gap 2 mm from border + pitch 6 per inch leather/pvc/pu/fabric:full pu leatherette.frame material (tropical wood / pine wood/ rubber wood):rubberwood moisture content :12 – 14 %.seat foam: (density, type) :24 density foam + pocket spring (49 nos. of dia 50 mm / seat) .spring rod dia =1.6mm+ 24 density foam.back foam: (density, type) :24 density foam + polyester fabric (recron).armrest foam: (density, type) :24 density foam belt/ webbing material:na .spring details ( s-spring / pocket spring):3.5 mm thick s spring .leg material:msl angle + leveling bush. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Other P.O. Chambers :Providing and fixing of sofa 3 seater from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers -1320(w) *800(d) *750(h).leather : synthetic.Frame material : tropical solid wood. Seat foam : polyurethane foam with recron layer.Foam density : 18 kg/ cubic cm..Back foam : polyurethane foam with silicon fill.At arms. Foam density : 22 kg/cubic cm. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Other P.O. Chambers :Providing and fixing of Sofa 1 seater from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers -85.5(w) *800(d) *750(h).leather : synthetic.Frame material : tropical solid wood.Seat foam : polyurethane foam with recron layer..Foam density : 18 kg/ cubic cm.Back foam : polyurethane foam with silicon fill.At arms. Foam density : 22 kg/cubic cm. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Other P.O. Chambers :Providing and fixing of Center table from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers . materials &dimension (+/- 2mm)-1100*645*450*440*210*10.table legs meterials&size : metal round tube-l x w x t-dia25x1.2 color : chrome.table top materials &size : (density / type) oval glass-.l x w x t -top: 1100x650x10mm.l x w x t-600x400x8mm.color : partial black.color: full black bottom .finishing: black top and chrome frame and legs . The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Other P.O. Chambers :Providing and fixing of corner table from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers materials & dimension (+/- 2mm)- 550*550*500*440*440*10.table legs meterials & size : metal round tube-l x w x t-dia25x1.2.color : chrome.table top materials & size : (density / type) oval glass-.l x w x t -top: 550x550x10mm.l x w x t-280x280x8mm.color : partial black.color: full black bottom.FINISHING: BLACK TOP AND CHROME FRAME AND LEGS.The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Other P.O. Chambers :Providing and fixing of visitor chair SEAT ASSEMBLY from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. *Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D) (2) BACK ASSEMBLY: The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette. BACK SIZE: 47.7 cm. (W) x 60.1 cm. (D) .Visitor TUBULAR FRAME: The tubular frame should be cantilever type and made of Ø2.54± 0.03 cm X 0.02 ± 0.016cm thick SS 202 tube. The back should be connected to frame through chrome plated high pressure die case connector piece

Other P.O. Chambers :Providing and fixing of Almirah Knockdown from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers. With 4 Shelves shall have an overall size of 900mm(W)x450mm(D)x1830mm(H) . The construction shall be rigid knock down construction and Material used shall be prime quality CRCA steel - panels from 0.6 mm thick & front frame . Shelf shall be 0.8 mm thick .Configuration (Door) shall be full height steel hinged door . Locking shall be Plastic Recessed Handle cum Cam lock with 3 way locking mechanism with shooting bolt arrangement . Height wise adjustable shelf mounting , Uniformly distributed load capacity per each full shelf shall be 80 Kg maximum . For Plain 4 Nos. of adjustable full shelves . The top shall be metal and Epoxy Powder coated finish to the thickness of 50 microns . The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Other P.O. Chambers :Paper Tray A-4 Size for Judgement Box ( APO ) Metal customized item.

Office of Other Courts :Proving & Fixing work station from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers per person - Recta shape with 1500W*600d mm - BIFMA LEVEL 3 CERTIFICATION MODEL Providing MS partiton system of 1200 ht . Overall thickness of partition shall be 57 mm ( +/- 5 mm ). panel based work station partition with flexible construction offering various functional and decorative finishes as well as cable management capacity. All trims made of aluminium extrusions. Blocks made out of a composite construction of MDF and paper honeycomb.Panel Blocks made of Fabric Tackable and white board.Tiles should be slid in to the panels from top before fixing the top horizontal. These tiles should be supported from top & bottom side with clips made from PP co polymer fitted in horizontal extrusion. Bottom tile and leg made of Mild steel with epoxy powder coated.Fabricated bottom frame as a welded structure of steel components. The panels and worktops are supported with MS legs with levelers at various locations depending on the layout requirements. Fabric magnetic tiles are fabric upholstered metal tiles in 0.6 mm thick G.I. Grade.Fabric tack tiles are fabric upholstered metal tiles in 0.6 mm thick G.I. Grade, with P.E. Foam in the tile for tack ability / acoustics. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Plain Metal tiles are made of 0.6 mm thick M.S. CRCA Grade D as per IS: 513 powder coated with Epoxy- Polyester finish.White board tiles are made of 8.0 mm thick particle board laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and having all its edges with minimum 0.5 mm thick PVC edging. Proving & Fixing work station or equivalent – 4 equal block based system – BIFMA level 3 Certified Model. Providing worktop of 600 mm depth . Work top shall be made of 25mm thick Plain Particle board interior grade conforming to IS:3087:1985 . The top shall be laminated with laminate of 1 mm thickness of approved shade as per IS:2046-1995 and glue of PVAC . Bottom shall have a backing laminate of minimum 0.6 mm thickness. All the edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hotmelt EVA glue.Worktop to be suppotred at both end with Peninsular legs.These Legs are made up of M.S. ERW tube of dia 89mm and of 2 mm thickness, pretreated and powder coated with POWDER coating. These are provided with M.S. Level adjuster, for adjustibility upto + 20 mm.Leg base is covered with ABS base cap .Work top shall be mounted onto the partition panels for work stations by means of cantilever brackets made from 2.0 mm thick CRCA grade D steel as per IS:513-1994 duly pretreated and powder coated in black colour.Keyboard Pullout tray shall be of size of 514mm(WIDTH) x 307mm(DEPTH) x 42mm (HEIGHT) made of 0.9 mm thick MS sheet of CRCA Grade ‘D’ as per IS :513-1994 The said tray shall be mounted on zinc electro plated (as per IS:1573-1996) single extension ball slides. CPU Trolley shall of size - L-225-330 mm , W-225 mm , H-330 mm made of MS 14BG Powder coated 50-60 micron DFT. Providing Free Standing 3 Drawer units .Welded Assembled. Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10)..0.8 thk CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, Rear .Side Stiffener & Bottom,1.2 thk CRCA Top Stiffener & Bottom stiffener.All Drawers with Double extension precision ball slide.10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism for ‘Box-File’ & ‘3 Box’ Pedestals.Top and front fascia made of 18 thk Wooden (PLB) Straight Edge Top / PVC Lipping on three Edges.Swiveling non-lockable Castors mounted below the body shell.Fifth roller arrangement mounted below File drawer to avoid toppling of unit when file drawer is pulled out. Size : 390 w x 435 d x 656 ht The rate shall include all materials, hardware and labour etc Make: Godrej/Herman Millar/Haworth/Knoll /steelcase.

Office of Other Courts :Providing and fixing of chairseat/back assembly from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers: the seat and back should be made from 1.2 ±0.1 cm.. thk. hot pressed plywood method described in. and upholstered with fabric and moulded polyurethane foam together with seat and back covers. the back foam should be designed with contoured lumbar support for extra comfort.* seat size: 45.0cm(w) x 42.0cm.(d) back size: 40.0cm(w) x 47.0cm.(h). seat /,back covers: the seat and back covers should be injection moulded in black co-polymer polypropylenehigh resilience (hr) polyurethane foam : the hr polyurethane foam should be moulded with density = 45 +/-21(g/neand_hardness load 16_± 2 kgf for 25%_compression armrest assembly (for 7046r): the one-piece armrests should be injection moulded from black nylon. the armrests should be fitted to the seat with armrest connecting brackets made of 0.5 ± 0.05 cm. thk. hr steel.permanent contact mechanism: the permanent contact mechanism should be designed with the following features• 360° revolving type.• 14° ±2°maximum-back-tilt-only.• upright position locking.• tilt tension adjustment pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm telescopic bellow assembly: the bellow should be .3 piece telescopic type and injection moulded in black polypropylene pedestal assembly: the pedestal should be injection moulded in black 30% glass-filled nylon and fitted with 5 nos. twin wheel castors. the pedestal should be 62.0 ±0.5cm. pitch-centre dia. (72.0 ±1.0cm with castors). twin wheel castors: the twin wheel castors should be injection moulded in black nylonOverall Dimensions of Chair .Seat Height - min 43.0 to max 54.0cm.Height - min87.5 to max 98.5cm. width & Depth of Chair as measured from pedestal - Width-71.0 cm and Depth-71.0 cm.. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Office of Other Courts :Providing and fixing of visitor chair ,seat/back assembly from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers: the seat made from 1.2 ±0.1cm. thk. hot pressed plywood and back should be injection moulded from black co-polymer polypropylene upholstered with fabric and moulded polyurethane foam together with seat and back covers. the back foam should be designed with contoured lumbar support for extra comfort. seat size: 45.ocrn(w) x 42.0cm.(d) back size: 39.0cm(w) x 38.ocm.(h) seat/back covers: the seat and back covers should be injection moulded in black co-polymer polypropylene. )polyurethane foam: the polyurethane foam should be moulded with density = 45 +/-2 kg/m' and hardness = 20 +1- 2 on hampden machine at 25% compression. armrest assembly: the armrests should be made of black integral skin polyurethane wtih 50-70 shore 'a' hardness and reinforced with m.s. insert. the p.u. armrests should be then fixed to black powder-coated ( dft 40-60 microns ) armrest brackets made of of 0.8 ± 0.05 cm thk. hr steel . the rh armrest bracket has provshould be ion for mounting retractable desklet. fixed type mechanism: the fixed type mechanism should be without back tilt. tubular frame: the tubular frame should be made up of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. m.s. e.r.w. tube and black powder coated ( dft 40-60 microns ). )desklet assembly: the desklet should be fixed to a retractable type mechanism & made of 1.8±0.05cm thk medium density fiberboard and membrane formed with black 0.04cm thk. pvc film. the bottom side should be provided with black backing laminate. the retractable mechanism enables the user to fold the desklet on the rh side of the chair when not in use. *approx. size of desklet: 34.5±0.1cm. (w) x 26.5±0.1cm. (d). The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Office of Other Courts :Providing and fixing of Almirah from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers & shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Office of Other Courts :Providing and fixing of rack from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers of size 1800mmx915 X387mm with provision of 5 shelves. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Office of Other Courts :Providing and fixing of stool from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers. Overall dimensions of stool are: Width- 47.3 cm, Depth- 47.3cm, Seat Height-46.5cmseat assembly: li should be circular type 0 30.0±0.5cm and made up of 0.1±0.012cm thk cr steel. it should be welded to the understructure and black powder coated ( dft 40-60 microns )understructure assembly: the understructure should be made of ms tube 0 2.2±0.03cm x 0.16±0.0128cm thk ms erw tube. it should be welded to the ms fabricated circular seat assembly and black powder coated ( dft 40-60 microns ). the understructure should be provided with black pp injection moulded ferrules. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Steno Office Other Courts :Proving & Fixing work station from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers per person - Recta shape with 1500W*600d mm - BIFMA LEVEL 3 CERTIFICATION MODEL Providing MS partiton system of 1200 ht . Overall thickness of partition shall be 57 mm ( +/- 5 mm ). panel based work station partition with flexible construction offering various functional and decorative finishes as well as cable management capacity. All trims made of aluminium extrusions. Blocks made out of a composite construction of MDF and paper honeycomb.Panel Blocks made of Fabric Tackable and white board.Tiles should be slid in to the panels from top before fixing the top horizontal. These tiles should be supported from top & bottom side with clips made from PP co polymer fitted in horizontal extrusion. Bottom tile and leg made of Mild steel with epoxy powder coated.Fabricated bottom frame as a welded structure of steel components. The panels and worktops are supported with MS legs with levelers at various locations depending on the layout requirements. Fabric magnetic tiles are fabric upholstered metal tiles in 0.6 mm thick G.I. Grade.Fabric tack tiles are fabric upholstered metal tiles in 0.6 mm thick G.I. Grade, with P.E. Foam in the tile for tack ability / acoustics. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Plain Metal tiles are made of 0.6 mm thick M.S. CRCA Grade D as per IS: 513 powder coated with Epoxy- Polyester finish.White board tiles are made of 8.0 mm thick particle board laminated with 0.6mm thick white glossy high pressure laminate on outer side & 0.6mm backing laminate on inner surface and having all its edges with minimum 0.5 mm thick PVC edging. Proving & Fixing work station or equivalent – 4 equal block based system – BIFMA level 3 Certified Model. Providing worktop of 600 mm depth . Work top shall be made of 25mm thick Plain Particle board interior grade conforming to IS:3087:1985 . The top shall be laminated with laminate of 1 mm thickness of approved shade as per IS:2046-1995 and glue of PVAC . Bottom shall have a backing laminate of minimum 0.6 mm thickness. All the edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hotmelt EVA glue.Worktop to be suppotred at both end with Peninsular legs.These Legs are made up of M.S. ERW tube of dia 89mm and of 2 mm thickness, pretreated and powder coated with POWDER coating. These are provided with M.S. Level adjuster, for adjustibility upto + 20 mm.Leg base is covered with ABS base cap .Work top shall be mounted onto the partition panels for work stations by means of cantilever brackets made from 2.0 mm thick CRCA grade D steel as per IS:513-1994 duly pretreated and powder coated in black colour..Keyboard Pullout tray shall be of size of 514mm(WIDTH) x 307mm(DEPTH) x 42mm (HEIGHT) made of 0.9 mm thick MS sheet of CRCA Grade ‘D’ as per IS :513-1994 The said tray shall be mounted on zinc electro plated (as per IS:1573-1996) single extension ball slides. CPU Trolley shall of size - L-225-330 mm , W-225 mm , H-330 mm made of MS 14BG Powder coated 50-60 micron DFT. Providing Free Standing 3 Drawer units .Welded Assembled. Epoxy Polyester Powder coated to the thickness of 50 microns (+/-10)..0.8 thk CRCA for Body Shell, Drawer Front & tray, Front Side Stiffener, Rear .Side Stiffener & Bottom,1.2 thk CRCA Top Stiffener & Bottom stiffener.All Drawers with Double extension precision ball slide.10 lever Cam Lock & Central RH locking with actuator & lock channel mechanism for ‘Box-File’ & ‘3 Box’ Pedestals.Top and front fascia made of 18 thk Wooden (PLB) Straight Edge Top / PVC Lipping on three Edges.Swiveling non-lockable Castors mounted below the body shell.Fifth roller arrangement mounted below File drawer to avoid toppling of unit when file drawer is pulled out. Size : 390 w x 435 d x 656 ht The rate shall include all materials, hardware and labour etc..Make: Godrej/Herman Millar/Haworth/Knoll /steelcase.

Steno Office Other Courts :Providing and fixing of midback chair seat/back assembly from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers: the seat and back should be made from 1.2 ±0.1 cm.. thk. hot pressed plywood method described in. and upholstered with fabric and moulded polyurethane foam together with seat and back covers. the back foam should be designed with contoured lumbar support for extra comfort. * seat size: 45.0cm(w) x 42.0cm.(d) back size: 40.0cm(w) x 47.0cm.(h). seat /,back covers: the seat and back covers should be injection moulded in black co-polymer polypropylenehigh resilience (hr) polyurethane foam : the hr polyurethane foam should be moulded with density = 45 +/-21(g/neand_hardness load 16_± 2 kgf for 25%_compression armrest assembly (for 7046r): the one-piece armrests should be injection moulded from black nylon. the armrests should be fitted to the seat with armrest connecting brackets made of 0.5 ± 0.05 cm. thk. hr steel.permanent contact mechanism: the permanent contact mechanism should be designed with the following features• 360° revolving type.• 14° ±2°maximum-back-tilt-only.• upright position locking.• tilt tension adjustment pneumatic height adjustment: the pneumatic height adjustment has an adjustment stroke of 11.0 ±0.3cm telescopic bellow assembly: the bellow should be .3 piece telescopic type and injection moulded in black polypropylene pedestal assembly: the pedestal should be injection moulded in black 30% glass-filled nylon and fitted with 5 nos. twin wheel castors. the pedestal should be 62.0 ±0.5cm. pitch-centre dia. (72.0 ±1.0cm with castors). twin wheel castors: the twin wheel castors should be injection moulded in black nylonOverall Dimensions of ChairSeat Height - min 43.0 to max 54.0cm.Height - min87.5 to max 98.5cm.Width & Depth of Chair as measured from pedestal - Width-71.0 cm and Depth-71.0 cm.. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Steno Office Other Courts :Providing and fixing of visitor chair ,seat/back assembly from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers: the seat made from 1.2 ±0.1cm. thk. hot pressed plywood and back should be injection moulded from black co-polymer polypropylene upholstered with fabric and moulded polyurethane foam together with seat and back covers. the back foam should be designed with contoured lumbar support for extra comfort. seat size: 45.ocrn(w) x 42.0cm.(d) back size: 39.0cm(w) x 38.ocm.(h) seat/back covers: the seat and back covers should be injection moulded in black co-polymer polypropylene. )polyurethane foam: the polyurethane foam should be moulded with density = 45 +/-2 kg/m' and hardness = 20 +1- 2 on hampden machine at 25% compression. armrest assembly: the armrests should be made of black integral skin polyurethane wtih 50-70 shore 'a' hardness and reinforced with m.s. insert. the p.u. armrests should be then fixed to black powder-coated ( dft 40-60 microns ) armrest brackets made of of 0.8 ± 0.05 cm thk. hr steel . the rh armrest bracket has provshould be ion for mounting retractable desklet. fixed type mechanism: the fixed type mechanism should be without back tilt. tubular frame: the tubular frame should be made up of 0 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. m.s. e.r.w. tube and black powder coated ( dft 40-60 microns ). )desklet assembly: the desklet should be fixed to a retractable type mechanism & made of 1.8±0.05cm thk medium density fiberboard and membrane formed with black 0.04cm thk. pvc film. the bottom side should be provided with black backing laminate. the retractable mechanism enables the user to fold the desklet on the rh side of the chair when not in use. *approx. size of desklet: 34.5±0.1cm. (w) x 26.5±0.1cm. (d). The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Steno Office Other Courts :Providing and fixing of Almirah from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers & shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The Storwel Plain should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and shelving options shall be available. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.

Steno Office Other Courts : Providing and fixing of stool from ISO 9001:2015, ISO 14001, OHSAS 18000, BIFMA,AIOTA, Certified Manufacturers. Overall dimensions of stool are: Width- 47.3 cm, Depth- 47.3cm, Seat Height-46.5cmseat assembly: li should be circular type 0 30.0±0.5cm and made up of 0.1±0.012cm thk cr steel. it should be welded to the understructure and black powder coated ( dft 40-60 microns )understructure assembly: the understructure should be made of ms tube 0 2.2±0.03cm x 0.16±0.0128cm thk ms erw tube. it should be welded to the ms fabricated circular seat assembly and black powder coated ( dft 40-60 microns ). the understructure should be provided with black pp injection moulded ferrules. The rate shall include all materials, hardware and labour etc. complete as per instruction of engineer-in charge and consultant. Make: Godrej/Herman Millar/Haworth/Knoll/Steelcase.