Public Works Department Tender

Providing, laying, spreading and compacting stone aggregates of specific sizes (63-45mm) to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming crushable screening to fill up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per Technical specification clause 405

Providing, laying, spreading and compacting stone aggregates of specific sizes(22.4-53mm) to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with 3 wheeled steel/ vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming crushable screening to fill up the interstices of coarse aggregate, watering and compacting to the required density grading 3 as per Technical specification clause 405

Brick edging on both sides of roads of 1st class bricks 8cm (3") wide & 12 cm (4.50") deep laid with mud mortor including labour & suplly of bricks finished to required templete and in proper alignment and also including dressing & ramming the excavated earth including all labour T & P sudries required for completion of work with material.(As per SOR No. 765)

Providing and applying primer coat with bitumen emulsion on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means as per MORD Technical Specification Clause 502 and direction of Engineer-in-charge

Providing and applying tack coat with Bitumen VG-10 using Prassur distributor at the rate of 0.35 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per MORD specification Clause 503 and as per direction of Engineer-in-charge to completion of work.

Providing, laying and rolling of open-graded premix carpet of 20 mm thick compacted composed of 13.2 mm to 5.6 mm aggregates of approved quarry using bitumen (VG-10) to required line, grade and level to serve as wearing course on a previously prepared base, including mixing by Mixol, laying and rolling with a three wheel 80-100 kN static roller, finished to required level and grades as per MORD Specification Clause 508 and as per direction of Engineer-in-charge to completion of work

Providing and laying seal coat Type-C to sealing the voids in a bituminous surface with 6.7 mm aggregates of approved quarry using bitumen (VG-10) to required laid to the specified levels, grade and cross fall as per MORD Specification Clause 510 and as per direction of Engineer-in-charge to completion of work.

Construction of un-reinforced, dowel jointed, at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base with 43 grade cement or any other type as per clause 1501.2.2 M 30 (grade), coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.20 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side form work (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plats including leveling the formwork as drawing), spreading the concrete with shovels, rakes, compacted using needls, screed and plate vibrators and finshed in contunuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approadch to bridge/culvert and construction joints admixtures as approved, curing of concrete slabs for 14days curing compound(where specified) and water finishing to lines and grades as per drawing and Techincal specification clause 1501.

Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.(SOR No. 251)

Providing and laying Cement concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone ballast 40 mm. nominal size) including supply of all materials. Labour and T&P etc. required for proper completion of the work and curing complete also including cost of formwork in foundation and floors.(SOR No. 280)

First class bricks work in 1:3 in cement and coarse sand of 1.25 F.M. mortar in foundation and plinth including supply of all materials, labour and T&P etc. required for proper completion of the work.(SOR No. 307(a)

12 mm thick plaster with cement mortar in proportion of 1:3 cement and coarse sand. (SOR No. 583)

R.C.C work with cement approved course sand and 2 cm {3/4") gauge approved stone ballast in the proportion of 1:2:4 in lintels of doors and windows excluding supply of reinforcement and its bending but including its fixing and bending the same with 24 B.W.G. G.I. binding wire and including neccessary centering and shuttering etc. and also including supply of all materials, labours and T & P etc. required for proper completion of the work. Binding wire cost being included in the item.(SOR No. 284A)

Mild steel or iron in plan work shch as reinforced concrete or reinforced brick work(when not included in overall rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorized overlapping shall be measured up to floor two level.(SOR No. (504)

Excavation in foundation in ordinary soil including lift up to 1.50 m. lead upto 30 m. and including filling ,watering and ramming of excavated earth in to the trenches of foundation and disposal of surplus earth as directed by Engineer in charge. BBK SOR CH.-4, Item no. 251

Providing and laying cement concrete in 1:4:8 (1 cement: 4 fine sand : 8 graded brick aggregate of 40 mm nominal size ) and curing complete, including supply of materials , T & P required for proper completion of work as per direction of Engineer in charge. BBK SOR CH.-5, Item no. 275

First class brick work in 1:3 cement and coarse sand mortar in foundation and plinth including supply of materials T & P required for proper completion of work as per direction of Engineer in charge. BBK SOR CH.-6, Item no. 307a

Providing and laying of 600mm dia hume pipe with collar in position including supply of materials , T & P required for proper completion of work as per direction of Engineer in charge.

Providing and laying of 350mm dia hume pipe with collar in position including supply of materials , T & P required for proper completion of work as per direction of Engineer in charge.

Struck cement pointing on brick work with 1 :3 cement mortar ( 1 cement : 3 fine sand ) including supply of materials , T & P required for proper completion of work as per direction of Engineer in charge. LKO SOR CH.-15, Item no. 13.31.1