Public Works Department Tender

Item Reflective Raised Pavement Marker Providing and fixing of raised pavement markers (Cat Eye) Type x-ASTMD-4956-04 Avery Dennision/3m(USA Make) having moulded body of polycarbonate, ASA, HIPS or ABS able to support a load of 13.635 M.T. tested in accordance with ASTMD 4280 type H and other requirement mentioned in MoRT&H Circular, its reflective lens made of micro prismatic lens (capable of providing total internal reflection of light), electronically welded to the body. The length, height and width of the body shall not exceed 130 mm, 20 mm and 105 mm respectively, The area of each reflective surface shall not be less than 13 Sq. cm . on each side sloping at the angle of 35 + 5 degree to the base to ensure maximum reflectively. it shall comply to specification of Category A of MoRT&H circular no. RW/NH 33023/10/97- DO-III dated 11.06.97 lenses shall be moulded of methyl methecrylate conforming to ASTMD 788 or equivalent. With 7 years warranty. Rate shall be inclusive of all taxes, royalty, etc. All T&P/ machine material and labour required for proper completion of work. Each 195.00 Note : The Composite warranty jointly signed by original manufacturer & authorized converter of at least 7 years shall be furnished on non judicial stamp of required denomination. As per Chapter No. 27 New Item 10

Supplying & installation of delineator (road way indicators,hazard markers ,object marker)80-100 cm .High above grond level ,painted black and white in 15 cm .Wide strip ,fitted with 80 x 100 mm rectanglular or 75 mm dia circular reflectorised panel at the top buried or pressed into the ground and conforming to IRC :79 and the drawing with tricolor - refractive sheet (15 x 3) Rate are inclusive of all taxes, royalty etc. all T & P /machine material and labour required for proper completion of work.As per Chapter No. 27 SI No New Item 10 SOR 2018

Provinding and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, Thickness of 2.5 mm is exclusive applied glass beads as per IRC 35 The Finished surface to level , uniform and free from streak and holes (ch. 27 SI No. 7 new item)

Provinding and laying of hot applied thermoplastic compound 5 mm thick including reflectorising glass beads @ 250 gms per sqm area, Thickness of 5 mm is exclusive applied glass beads as per IRC 35 The Finished surface to level , uniform and free from streak and holes (For Repeated Bar) (ch. 27 SI No. 7 new item)

Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cment conc. 45 cm x 45 cm x 60 cm, 60 cm below ground lvel as per approved drawing(30x90 object Hazard Board) (ch. 27 SI No. 6j)

Supply, fixing and hoisting of 6.00-7.00 m. span Cantilever Structure in position with one vertical post of 6.00 M. clear height from the top of R.C.C. foundation made of 300 mm. dia pipe welded with 10 mm thick MS plate at bottom supported with 10 mm thick MS plate stiffners & two nos. 8 mm thick MS plates at top welded with structure of 40 mm NB (M) pipe comprising of horizontal, vertical & bracing pipe of 32 mm NB (M) as per structural design requirements & approved drawing with vertical & lateral clearance given in clause 802.2 & 802.3 including one coat of primer and two coats of synthetic enamel paint on the whole structure & installed as per clause 802.7 over a designed support system made up of concrete including excavation, lean concrete 1:4:8 cement, coarse sand and approved 20 mm grit and R.C.C. 1:2:4 with cement, coarse sand and approved 20 mm grit complete for fixing the complete structure in position as per direction of E/I charge. With 7 years warranty. Rates include design, fabrication, supply, transportation and erection of the signage structure inclusive of all taxes As per Chapter No. 27 SI No New Item 8

Retro Reflective Signs (Type-IV Sheet) for both sideProviding and fixing retro-reflective signboards comprising of customised modular PU Epoxy Coated MS angle iron frame work, aluminum composite panel (ACP) as base board. micro prismatic retro-reflective sheet and electro cut colored overlay film/latex printing. The horizontal and vertical members including inclined outer members of the MS frame module shall be made of pair MS angle iron. No panel size shall be more than one sqm and each panel shall be braced diagonally (one way only) with MS angle. The MS frame module shall have length not more than 3 mtr. The aluminum composite panel (ACP) shall have a thickness of 4mm with 0.5 mm thick skin of aluminum on both sides. The ACP shall be fixed on the MS frame with pop riveting or with self taping SS screws 5mm dia spaced not more than 300mm centre to centre ensuring that no riveting is seen on either face of the frame. On the front visible face of the ACP, micro prismatic retro-reflective sheet conforming to Type-IV of ASTM: D 4956-09 shall be pressure fixed. The retro-reflective sheeting shall be tested for 3 year outdoor weathering test in Indian conditions as per IRC 67: 2012 & proof of the same in form of government report shall be uploaded with quoting tender. The rate include all materials, labour, equipments, fabrication, transportation, erection, installation and incidentals all complete as per direction of the Engineer-in-Charge. Signage on MS angle frame of (35x35x5)mm As per Chapter No. 27 SI No. 4