Public Works Department Tender

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501. (Including all T&P, Labour, Material, Royalty Tax but excluding GST)

Providing and applying primer coat of Low Porosity with Bitumen emulsion on prepared surface of granular base including cleaning of road surface and spraying primer at rate of 0.70 Kg/Sqm using mechanical means as per Technical Specification Clause 502. (Including all T&P, Labour, Material, Royalty Tax but excluding GST)

Providing and applying tack coat with VG-10 using bitumen distributor at the rate of 0.25 kg per sqm on the prepared granular surfaces treated with primer/Bituminous surface as per Technical Specification Clause 503. (Including all T&P, Labour, Material, Royalty Tax but excluding GST)

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates using VG-10 to required line, grade and level to serve as wearing course on a previously prepared base by manual means, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades as per Technical Specification Clause 508 (By Manual Means) (Including all T&P, Labour, Material, Royalty Tax but excluding GST)

Providing and laying Type "C" seal coat by manual means with VG-10 sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall as per Technical Specification Clause 510 ( By Manual Means) (Including all T&P, Labour, Material, Royalty Tax but excluding GST)

Brick Soling .Laying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross-section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolliing the same with three wheel road roller 80-100 kN as per Technical Specification Clause 412 (Including all T&P, Labour, Material, Royalty Tax but excluding GST)

Excavation for roadway in soil using manual means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per Technical Specification Clause 302.3 (Including all T&P, Labour, Material, Royalty Tax but excluding GST)

Providing concrete for plain/reinforced concrete (P.C.C grade M 10) in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 (Including all T&P, Labour, Material, Royalty Tax but excluding GST)

Providing concrete for plain/reinforced concrete (R.C.C grade M 20) in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 (Including all T&P, Labour, Material, Royalty Tax but excluding GST)

Supplying, fitting and placing HYSD bar reinforcement in foundation complete as per drawings and technical specifications Clauses 1000 and 1202. (Including all T&P, Labour, Material, Royalty Tax but excluding GST) HYSD TATA (SAIL/TATA/JSL)

First Year Maintainance (@0% of Total Work Amount of S.No. 1 to S.No.13)

Second Year Maintainance (@1.5% of Total Work Amount of S.No. 1 to S.No.13)

Third Year Maintainance (@3.0% of Total Work Amount of S.No. 1 to S.No.13)

Fourth Year Maintainance (@4.5% of Total Work Amount of S.No. 1 to S.No.13)

Fifth Year Maintainance (@6.0% of Total Work Amount of S.No. 1 to S.No.13)